Barium hydroxide

When exposed to sunlight, it is converted to a white insoluble resin, disacryl. Oxidized by air to propenoic acid small amounts of hy-droquinone will inhibit this. Bromine forms a dibromide which is converted by barium hydroxide into DL-fructose. The acrid odour of burning fats is due to traces of propenal. It is used in the production of methionine and in controlled polymerization reactions to give acrolein polymers. ... 

Phosphine can be prepared by the reaction of a strong alkali with white phosphorus potassium, sodium and barium hydroxides may be used ... 

Mix 200 g. of adipic acid intimately with 10 g. of finely-powdered, crystallised barium hydroxide. Place the mixture in a 1-litre distilling flask, fitted with a thermometer reaching to within 5 mm. of the bottom connect the flask with a condenser and receiver. Heat the mixture gradually in an air bath (1) to 285-295° during about 90 minutes and maintain it at this temperature mitil only a small amount of dry residue remains in the flask this requires a further 2 hours. The temperature must not be allowed to rise above 300°, since at this temperature the adipic acid distils quite rapidly the best working temperature is 290°. The cycZopentanone distils slowly accompanied by a little adipic acid. Separate the ketone from the water in the distillate, and dry it with anhydrous potassium carbonate this treatment simultaneously removes the traces of adipic acid present. Finally distil from a flask of suitable size and collect the cycZopentanone at 128-131°. The yield is 92 g. 

If the outlet of the siphon tube at the bottom of the Soxhlet apparatus is well plugged with cotton wool so that no finely-divided bariuna hydroxide can pass into the flask, the barium hydroxide may be placed directly into the extractor until the latter is three-quarters full the remaining space is filled with glass wool. 

If crystallised barium hydroxide (Ba(OH) 8H,0) is employed, this becomes dehydrated after one run the anhydrous compound is just as satisfactory and may be used repeatedly. 

Prepare a solution of 41 g. of anhydrous palladium chloride (1) in 10 ml. of concentrated hydrochloric acid and 25 ml. of water (as in A). Add all at once 60 ml. of 6iV-sulphuric acid to a rapidly stirred, hot (80°) solution of 63 1 g. of A.R. crystallised barium hydroxide in 600 ml. of water contained in a 2-htre beaker. Add more 6iV-sulphuric acid to render the suspension just acid to htmus (5). Introduce the palladium chloride solution and 4 ml. of 37 per cent, formaldehyde solution into the hot mechanically stirred suspension of barium sulphate. Render the suspension slightly alkaline with 30 per cent, sodium hydroxide solution, continue the stirring for 5 minutes longer, and allow the catalyst to settle. Decant the clear supernatant hquid, replace it by water and resuspend the catalyst. Wash the catalyst by decantation 8-10 times and then collect it on a medium - porosity sintered glass funnel, wash it with five 25 ml. portions of water and suck as dry as possible. Dry the funnel and contents at 80°, powder the catalyst (48 g.), and store it in a tightly stoppered bottle. 

The most stable protected alcohol derivatives are the methyl ethers. These are often employed in carbohydrate chemistry and can be made with dimethyl sulfate in the presence of aqueous sodium or barium hydroxides in DMF or DMSO. Simple ethers may be cleaved by treatment with BCI3 or BBr, but generally methyl ethers are too stable to be used for routine protection of alcohols. They are more useful as volatile derivatives in gas-chromatographic and mass-spectrometric analyses. So the most labile (trimethylsilyl ether) and the most stable (methyl ether) alcohol derivatives are useful in analysis, but in synthesis they can be used only in exceptional cases. In synthesis, easily accessible intermediates of medium stability are most helpful. 

Tetrahydrofurfuryl alcohol reacts with ammonia to give a variety of nitrogen containing compounds depending on the conditions employed. Over a barium hydroxide-promoted skeletal nickel—aluminum catalyst, 2-tetrahydrofurfur5iarnine [4795-29-3] is produced (113—115). With paHadium on alumina catalyst in the vapor phase (250—300°C), pyridine [110-86-1] is the principal product (116—117) pyridine also is formed using Zn and Cr based catalysts (118,119). At low pressure and 200°C over a reduced nickel catalyst, piperidine is obtained in good yield (120,121). 

The commercial product is a dull yeUow powder containing about 90% Ba02 and about 8.5% active oxygen the remainder is mainly barium carbonate and barium hydroxide. The principal use is in pyrotechnics, but there are also small uses in the curing of polysulftde mbbers and in the production of certain titanium—aluminum alloys. 

Compared to the hydroxides of calcium and strontiuim, barium hydroxide is the most water-soluble and also the strongest base. Additionally, barium hydroxide is more difficult to convert to the oxide by heating than are the corresponding hydroxides of calcium and strontium. Barium oxide is more readily converted to the peroxide than are the oxides of the other alkaline earths. 

Barium acetate [543-80-6] Ba(C2H202)2, crystallines from an aqueous solution of acetic acid and barium carbonate or barium hydroxide. The level of hydration depends on crystallization temperature. At <24.7°C the trihydrate, density 2.02 g/mL is formed from 24.7 to 41 °C barium acetate monohydrate [5908-64-5] density 2.19 g/mL precipitates and above 41 °C the anhydrous salt, density 2.47 g/mL results. The monohydrate becomes anhydrous at 110°C. At 20°C, 76 g of the monohydrate dissolves in 100 g of water. Barium acetate is used in printing fabrics, lubricating grease, and as a catalyst for organic reactions. 

In the hot leaching step, barium metasiUcate is insoluble, and the orthosiUcate yields only one-half of its barium value to give barium hydroxide... 

Barium hydroxide is the strongest base and has the greatest water-solubility of the alkaline-earth elements. Barium hydroxide (barium hydrate, caustic baryta) exists as the octahydrate [12230-71 -6], Ba(OH)2 8H20, the monohydrate [22326-55-2], Ba(OH)2 H20, or as the anhydrous [17194-00-2] material, Ba(OH)2. The octahydrate and monohydrate have sp gr 2.18 and 3.74, respectively. The mp of the octahydrate and anhydrous are 77.9 °C and 407°C, respectively. 

Barium nitrite [13465-94-6] Ba(N02)2, crystallines from aqueous solution as barium nitrite monohydrate [7787-38-4], Ba(N02)2 H2O, which has yellowish hexagonal crystals, sp gr 3.173, solubihty 54.8 g Ba(NO2)2/100 g H2O at 0°C, 319 g at 100°C. The monohydrate loses its water of crystallization at 116°C. Anhydrous barium nitrite, sp gr 3.234, melts at 267°C and decomposes at 270 °C into BaO, NO, and N2. Barium nitrite may be prepared by crystallization from a solution of equivalent quantities of barium chloride and sodium nitrite, by thermal decomposition of barium nitrate in an atmosphere of NO, or by treating barium hydroxide or barium carbonate with the gaseous oxidiation products of ammonia. It has been used in diazotization reactions. 

BaS hydrolyzes to Ba(OH)2 and barium hydrosulfide. Cooling of an aqueous BaS solution can precipitate the double salt barium hydroxide sulfide hydrate [42821-46-3J, Ba(OH)2 Ba(SH)2 -xH O. 

Calcium hydroxide is a better catalyst at 40-90° than barium hydroxide, magnesium hydroxide, sodium hydroxide, and sodium carbonate for preparing pentaerythritol. Corbellini and... 

Di-(/)-chlorophenyl)-acetic acid has been made by the action of alcoholic potassium hydroxide on l,l-di-(/>-chlorophenyl)-2,2-dichloroethane by the action of barium hydroxide on DDT in ethylene glycol and by the condensation of chlorobenzene with glyoxylic acid. ... 

---