Atmospheric Pressure Apparatus

Several simplifying modifications have been added to this basic system. In one, a stopcock was placed at the bottom of the burette through which the liquid could be titrated into the burette from a raised leveling bulb. The other was the attachment to the manifold of a shorter U-tube which could be isolated from the system by a stopcock. Filling this with water or a similar liquid provides 

While these reactors are commonly used under ambient conditions, temperature control of the reaction can be accomplished by using jacketed reaction flasks such as that pictured in Fig. 6.8 with a thermostatted liquid pumped through the jacket. 

---

Atmospheric pressure apparatus. Isomerization experiments at atmospheric pressure were carried out in an all-glass system equipped with greaseless values, a flow meter, a U-shaped silica reactor, a double TCD system recording the pressure of reactant (provided by a saturator) before the reactor and the pressure of the products after the reactor, a system to extract the products for GC analysis and a needle valve to regulate gas flow. The catalyst was placed on a silica fritted disc and the reactor was operated as a fixed bed at constant pressure and temperature. Hydrocarbons were introduced at a set pressure and hydrogen was used as complement to the atmospheric pressure on the catalyst. 

Chill the concentrated solution of the amine hydrochloride in ice-water, and then cautiously with stirring add an excess of 20% aqueous sodium hydroxide solution to liberate the amine. Pour the mixture into a separating-funnel, and rinse out the flask or basin with ether into the funnel. Extract the mixture twice with ether (2 X25 ml.). Dry the united ether extracts over flake or powdered sodium hydroxide, preferably overnight. Distil the dry filtered extract from an apparatus similar to that used for the oxime when the ether has been removed, distil the amine slowly under water-pump pressure, using a capillary tube having a soda-lime guard - tube to ensure that only dry air free from carbon dioxide passes through the liquid. Collect the amine, b.p. 59-61°/12 mm. at atmospheric pressure it has b.p. 163-164°. Yield, 18 g. 

If a vacuum-distillation apparatus is not available for the above preparation, the crude product may be distilled at atmospheric pressure and the acetoacetate collected as the fraction boiling at i75 -i85 . A pure preparation cannot be obtained in this way, however, because the ester decomposes slightly when distilled at atmospheric pressure. 

Carrying out a combustion. The apparatus (Fig. 85, p. 469) will have been left with the bottle W connected to the beak of the combustion tube via the guard tube V and with all the taps shut, the combustion tube, which is dways allowed to cool down while connected to the oxygen source, will therefore be full of oxygen at slightly above atmospheric pressure, thus preventing any leaking in of carbon dioxide or water vapour from the air. 

When the volume of mother liquor is large and the amount of crystals small, the apparatus of Fig. II, 32, 1 may be used. The large pear-shaped receiver is supported on a metal ring attached to a stand. When the receiver is about two-thirds fuU, atmospheric pressure is restored by suitably rotating the three-way stopcock the filtrate may then be removed by opening the tap at the lower end. The apparatus is again exhausted and the filtration continued. 

II, 36, 1 is almost self explanatory two ground glass joints are used, but these may be replaced by rubber stoppers, if desired. The crude substance is placed in the flask A. Stopcocks 1 and 2 are closed, and the apparatus is exhausted through tap 3 the indifferent gas is then allowed to enter the apparatus to atmospheric pressure. The evacuation and filling with inert gas are repeated several times. The solvent is added through the tap funnel B. 

Vinylacetic acid. Place 134 g. (161 ml.) of allyl cyanide (3) and 200 ml. of concentrated hydrochloric acid in a 1-htre round-bottomed flask attached to a reflux condenser. Warm the mixture cautiously with a small flame and shake from time to time. After 7-10 minutes, a vigorous reaction sets in and the mixture refluxes remove the flame and cool the flask, if necessary, in cold water. Ammonium chloride crystallises out. When the reaction subsides, reflux the mixture for 15 minutes. Then add 200 ml. of water, cool and separate the upper layer of acid. Extract the aqueous layer with three 100 ml. portions of ether. Combine the acid and the ether extracts, and remove the ether under atmospheric pressure in a 250 ml. Claisen flask with fractionating side arm (compare Fig. II, 13, 4) continue the heating on a water bath until the temperature of the vapour reaches 70°. Allow the apparatus to cool and distil under diminished pressure (compare Fig. II, 20, 1) , collect the fraction (a) distilling up to 71°/14 mm. and (6) at 72-74°/14 mm. (chiefly at 72 5°/ 14 mm.). A dark residue (about 10 ml.) and some white sohd ( crotonio acid) remains in the flask. Fraction (6) weighs 100 g. and is analytically pure vinylacetic acid. Fraction (a) weighs about 50 g. and separates into two layers remove the water layer, dry with anhydrous sodium sulphate and distil from a 50 ml. Claisen flask with fractionating side arm a further 15 g. of reasonably pure acid, b.p. 69-70°/12 mm., is obtained. 

Diphenyl is reduced comparatively slowly to di Wohexyl at atmospheric pressure a pressure of 3-6 atmospheres is recommended (uae the apparatus shown in Fig, Vly 4 1),... 

The apparatus required is similar to that described for Diphenylmelhane (Section IV,4). Place a mixture of 200 g. (230 ml.) of dry benzene and 40 g. (26 ml.) of dry chloroform (1) in the flask, and add 35 g. of anhydrous aluminium chloride in portions of about 6 g. at intervals of 5 minutes with constant shaking. The reaction sets in upon the addition of the aluminium chloride and the liquid boils with the evolution of hydrogen chloride. Complete the reaction by refluxing for 30 minutes on a water bath. When cold, pour the contents of the flask very cautiously on to 250 g. of crushed ice and 10 ml. of concentrated hydrochloric acid. Separate the upper benzene layer, dry it with anhydrous calcium chloride or magnesium sulphate, and remove the benzene in a 100 ml. Claisen flask (see Fig. II, 13, 4) at atmospheric pressure. Distil the remaining oil under reduced pressure use the apparatus shown in Fig. 11,19, 1, and collect the fraction b.p. 190-215°/10 mm. separately. This is crude triphenylmethane and solidifies on cooling. Recrystallise it from about four times its weight of ethyl alcohol (2) the triphenylmethane separates in needles and melts at 92°. The yield is 30 g. 

Liberate the free base by adding to the phenylhydrazine hydrochloride 125 ml. of 25 per cent, sodium hydroxide solution. Extract the phenyl-hydrazine with two 40 ml. portions of benzene, dry the extracts with 25 g. of sodium hydroxide pellets or with anhydrous potassium carbonate thorough drying is essential if foaming in the subsequent distillation is to be avoided. Most of the benzene may now be distilled under atmospheric pressure, and the residual phenylhydrazine under reduced pressure. For this purpose, fit a small dropping funnel to the main neck of a 100 ml. Claisen flask (which contains a few fragments of porous porcelain) and assemble the rest of the apparatus as in Fig. II, 20, 1, but do not connect the Perkin triangle to the pump. Run in about 40 ml. of the benzene, solution into the flask, heat the latter in an air bath (Fig. II, 5, 3) so that... 

Ethyl phenylethylmalonate. In a dry 500 ml. round-bottomed flask, fitted with a reflux condenser and guard tube, prepare a solution of sodium ethoxide from 7 0 g. of clean sodium and 150 ml. of super dry ethyl alcohol in the usual manner add 1 5 ml. of pure ethyl acetate (dried over anhydrous calcium sulphate) to the solution at 60° and maintain this temperature for 30 minutes. Meanwhile equip a 1 litre threenecked flask with a dropping funnel, a mercury-sealed mechanical stirrer and a double surface reflux condenser the apparatus must be perfectly dry and guard tubes should be inserted in the funnel and condenser respectively. Place a mixture of 74 g. of ethyl phenylmalonate and 60 g. of ethyl iodide in the flask. Heat the apparatus in a bath at 80° and add the sodium ethoxide solution, with stirring, at such a rate that a drop of the reaction mixture when mixed with a drop of phenolphthalein indieator is never more than faintly pink. The addition occupies 2-2 -5 hoius continue the stirring for a fiuther 1 hour at 80°. Allow the flask to cool, equip it for distillation under reduced pressure (water pump) and distil off the alcohol. Add 100 ml. of water to the residue in the flask and extract the ester with three 100 ml. portions of benzene. Dry the combined extracts with anhydrous magnesium sulphate, distil off the benzene at atmospheric pressure and the residue under diminished pressure. C ollect the ethyl phenylethylmalonate at 159-160°/8 mm. The yield is 72 g. 

XII,2. SOME TYPICAL OPERATIONS ON THE SEMIMICRO SCALE 1. Distillation at atmospheric pressure.—A simple apparatus is shown in Fig. XII, 2, 1 the pear-shaped distilling flask with long side... 

Sublimation.—This is a valuable means for the purification of many organic substances and is admirably adapted for small scale work since losses are generally small. Sublimation may be carried out either at atmospheric pressure or under reduced pressure. The apparatus shown in Fig. XII, 2, 20 is simple and effective the sublimate is collected on the cold finger condenser. 

A solution of 4,4-dimethyl-5a-androst-l-en-3-one (128, 14 mg) in cyclohexane (3 ml) is stirred in a microhydrogenation apparatus in the presence of 10 % palladium-on-charcoal (15 mg) at atmospheric pressure and room temperature. The uptake of one eq of deuterium (1.15 ml) is complete in about 1 min and no more deuterium is consumed. After 5 min the catalyst is removed by filtration, and the solvent evaporated under reduced pressure. The resulting l<, 2< -d2-4,4-dimethyl-5a-androstan-3-one (129, 13 mg, 93%), mp 120-122°, exhibits 87% isotopic purity and 13% d species. ... 

Dicyclopentadiene (50 g, 0.38 mole) is dissolved in 100 ml of anhydrous ether. Platinum oxide (0.25 g) is added, and the mixture is hydrogenated in a Parr apparatus at an initial pressure of 50 psi. Initially the reaction mixture becomes warm. The absorption of 2 mole equivalents of hydrogen takes 4-6 hours. The mixture is filtered by suction to remove the catalyst, and the filtrate is distilled at atmospheric pressure through a short fractionating column. 

In a short path distilling apparatus is placed 3-5 g of 1,1-cyclohexanedicarboxylic acid. The flask is heated in an oil, sand, or metal bath to 160-170° until all the effervescence stops then the temperature of the bath is raised to 210°. Cyclobutanecarboxylic acid distills over at 191 -197°. It may be purified by redistillation at atmospheric pressure, bp 195-196°. 

When a solid compound possesses a relatively high vapor pressure below its melting point, it may be possible to purify it by sublimation. Selenium dioxide, for example, is easily purified prior to use by sublimation at atmospheric pressure (Chapter 1, Section XI). More commonly, the method of choice is sublimation at reduced pressure, which allows more ready evaporation of solids with limited volatility. A convenient vacuum sublimation apparatus is shown in Fig. A3.19. The impure sample is placed in the... 

D-1160 is run under vacuum (one millimeter of mercury). The results are converted to atmospheric pressure, using standard cor relations. Some newer apparatuses have built-in software that performs the conversion automatically. D-1160 is limited to a maximum EP temperature of about 1,000°F (538°C) at atmospheric pressure. Above this temperature, the sample begins to crack thermally. 

---