Aromatic ether-ketone with

Almost simultaneous with the report of the preparation of polyarylether sulfones, aromatic polyether ketones were prepared via the Ni(0) catalyzed polymerization of aromatic ether ketones with chloro groups at each terminus (equation 53) (181). The reaction proceeds rapidly under mild conditions. 

Producing of Crystalline Aromatic Poly ketone with Simple Ether and Sulphide Linkages. Japan Patent Application 62-530. 

The synthesis and characterization of a full aromatic thermotropic liquid crystalline poly (aryl ether ketone) with pendant chlorine group (CIPAEK)... 

In another report, polyether ketones containing carboranes in the backbone of aromatic units were synthesized by the electrophilic condensation between the ether, l,2-(4-PhOC6H4)2-l,2-C2B10H10, and the dicarboxylic acid, l,2-(4-C02HC6H4)2-l,2-C2BioH,o, with trifluoro-methanesulfo-nic acid (Figure 26.21). This phenylene ether carboranylene ketone (PECK) polymer (54) was found to be extremely thermally stable and showed a much smaller mass loss, up to 1000°C, than was observed for conventional aromatic ether-ketones (Mark and Kenneth, 2002). 

J. Lee, C. S. Marvel, Poly aromatic ether-ketone sulfonamides prepared from polydiphenyl ether-ketones by chlorosulfonation and treatment with secondary amines, J. Polym. Sci Polym. Chem. Ed. 22(2), 295-301 (1984). 

Rapid, simple, quaUtative methods suitable for determining the presence of benzene in the workplace or surroundings have been utilized since the 1930s. Many early tests offered methods for detection of aromatics but were not specific for benzene. A straightforward test allowing selective detection of benzene involves nitration of a sample to y -dinitrobenzene and reaction of the resultant ether extract with an ethanoHc solution of sodium hydroxide and methyl ethyl ketone (2-butanone), followed by the addition of acetic acid to eliminate interferences from toluene and xylenes. Benzene imparts a persistent red color to the solution (87). The method is claimed to be sensitive to concentrations as low as 0.27 ppm benzene from 10 mL air samples. 

Polyarylether Ketones. The aromatic polyether ketones are tme thermoplastics. Although several are commercially available, two resins in particular, poly ether ether ketone [31694-16-3] (PEEK) from ICI and poly ether ketone ketone (PEKK) from Du Pont, have received most of the attention. PEEK was first synthesized in 1981 (20) and has been well studied it is the subject of numerous papers because of its potential use in high performance aircraft. Tough, semicrystalline PEEK is prepared by the condensation of bis(4-fiuorophenyl) ketone with the potassium salt of bis(4-hydroxyphenyl) ketone in a diaryl sulfone solvent, such as diphenyl sulfone. The choice of solvent is critical other solvents, such as Hquid HE, promote the reaction but lead to premature low molecular-weight crystals, which do not exhibit sufficient toughness (21). 

Polar acceptors include, in roughly descending order of strength, amines, ethers, ketones, aldehydes and esters (with aromatic materials usually being more powerful than aliphatics). 

The rates of the reactions of several aromatic ketones with alkyllithium reagents have been examined. The reaction of 2,4-dimethyl-4 -(methylthio)benzophenone with methyl-lithium in ether exhibits the rate expression ... 

The 10l -acetoxy group can be red actively removed with zinc and acetic acid or chromous chloride to give I9-norsteroids in high yield. Thermal elimination (boiling tetralin) of acetic acid from the crude 10)5-acetoxy-A -3-ketone or treatment with methanolic alkali leads to aromatization of ring A. Estrone alkyl ethers are formed from 10)5-acetoxy-19-nor-A -androstene-3,17-dione by treatment with alcohols and perchloric acid. Similar aromatizations are observed with 5,10-oxido, 5,10-dihydroxy, 5,10-halohydrins or 5,10-dihalo-3-ketones. ... 

Notable examples of general synthetic procedures in Volume 47 include the synthesis of aromatic aldehydes (from dichloro-methyl methyl ether), aliphatic aldehydes (from alkyl halides and trimethylamine oxide and by oxidation of alcohols using dimethyl sulfoxide, dicyclohexylcarbodiimide, and pyridinum trifluoro-acetate the latter method is particularly useful since the conditions are so mild), carbethoxycycloalkanones (from sodium hydride, diethyl carbonate, and the cycloalkanone), m-dialkylbenzenes (from the />-isomer by isomerization with hydrogen fluoride and boron trifluoride), and the deamination of amines (by conversion to the nitrosoamide and thermolysis to the ester). Other general methods are represented by the synthesis of 1 J-difluoroolefins (from sodium chlorodifluoroacetate, triphenyl phosphine, and an aldehyde or ketone), the nitration of aromatic rings (with ni-tronium tetrafluoroborate), the reductive methylation of aromatic nitro compounds (with formaldehyde and hydrogen), the synthesis of dialkyl ketones (from carboxylic acids and iron powder), and the preparation of 1-substituted cyclopropanols (from the condensation of a 1,3-dichloro-2-propanol derivative and ethyl-... 

The chemistry of indium metal is the subject of current investigation, especially since the reactions induced by it can be performed in aqueous solution.15 The selective reductions of ethyl 4-nitrobenzoate (entry 1), 2-nitrobenzyl alcohol (entry 2), l-bromo-4-nitrobenzene (entry 3), 4-nitrocinnamyl alcohol (entry 4), 4-nitrobenzonitrile (entry 5), 4-nitrobenzamide (entry 6), 4-nitroanisole (entry 7), and 2-nitrofluorenone (entry 8) with indium metal in the presence of ammonium chloride using aqueous ethanol were performed and the corresponding amines were produced in good yield. These results indicate a useful selectivity in the reduction procedure. For example, ester, nitrile, bromo, amide, benzylic ketone, benzylic alcohol, aromatic ether, and unsaturated bonds remained unaffected during this transformation. Many of the previous methods produce a mixture of compounds. Other metals like zinc, tin, and iron usually require acid-catalysts for the activation process, with resultant problems of waste disposal. 

The only other functional group is the conjugated unsaturated ester. This functionality is remote from the stereocenters and the ketone functionality, and does not play a key role in most of the reported syntheses. Most of the syntheses use cyclic starting materials. Those in Schemes 13.4 and 13.5 lead back to a para-substituted aromatic ether. The syntheses in Schemes 13.7 and 13.8 begin with an accessible terpene intermediate. The syntheses in Schemes 13.10 and 13.11 start with cyclohexenone. Scheme 13.3 presents a retrosynthetic analysis leading to the key intermediates used for the syntheses in... 

Metal ketyls are ion-radicals analogous to semiquinone ion radicals and may be considered either oxygen or carbon free radicals. They are readily prepared by treating aromatic ketones with alkali metals in dry ether, benzene, or liquid ammonia under an inert atmosphere.124 125 Benzophenone potassium has been shown to be paramagnetic in the solid state.126... 

The 0/7/fo-alkylation of aromatic ketones with olefins can also be achieved by using the rhodium bis-olefin complex [C5Me5Rh(C2H3SiMe3)2] 2, as shown in Equation (9).7 This reaction is applied to a series of olefins (allyltrimethyl-silane, 1-pentene, norbornene, 2,2 -dimethyl-3-butene, cyclopentene, and vinyl ethyl ether) and aromatic ketones (benzophenone, 4,4 -dimethoxybenzophenone, 3,3 -bis(trifluoromethyl)benzophenone, dibenzosuberone, acetophenone, />-chloroacetophenone, and />-(trifluoromethyl)acetophenone). 

Aromatic poly(aryl ether ketone)s containing 1,4-naphthalene moieties were prepared by the reaction of a bisphenol and 2 in the presence of potassium carbonate in DM Ac at 160°C as depicted in Scheme 3. A typical polymerization was carried out as follows To a 100-ml round-bottom flask was added 8.32 g (O.OlOmol) of2, 3.36g (O.OlOmol) of4,4 -(hexafluoroisopropylidene) diphenol, 51.2 g ofDMAc, and 3.1 g (0.022 mol) of potassium carbonate. The mixture was heated to 160°C with stirring under nitrogen for 18 h. The mixture was allowed to cool to room temperature. The polymer was precipitated by pouring the reaction mixture into a blender containing about 100 ml of water, filtered, washed three times with water and dried to yield 8.1 g (92% yield) as a white powder. 

Compounds 1 and 2 were identified by FTIR and 13C-NMR. The 13C proton decoupled spectra for 1 and 2 are dominated by signals ranging from 62 to 195 ppm. The 13C chemical shift assignments were made based on comparisons with 4,4 -(hexafluoroisopropylidene)diphenol and from calculations based on substituted benzenes and naphthalenes.15 The 13C-NMR spectrum clearly showed that the Friedel-Crafts acylation of 1 by 4-fluorobenzoyl chloride yielded the 1,4-addition product exclusively. The 13C chemical shifts for 2 are listed in Table 8.1. The key structural features in the FTIR spectrum of2 include the following absorptions aromatic C-H, 3074 cnr1, ketone C=0, 1658 cm-1, aromatic ether Ar—0—Ar, 1245 cm-1, and C—F, 1175 cm-1. 

Hexafluoroisopropylidene-unit-containing aromatic poly(ether ketone)s were first synthesized from an alkaline metal salt of Bisphenol AF (1) and 4,4 -difluoro-benzophenone.14 Cassidy and co-workers prepared hexafluoroisopropylidene-unit-containing poly(ether ketone)s by condensing 2,2-bis[4-(4-fluorobenzoyl)-phenyl]-l,l,l,3,3,3-hexafluoropropane (9) and 2,2-bis[4-(4-fluorobenzoyl)-phenyljpropane (10) with Bisphenol AF (1) or Bisphenol A (4) (Scheme 7).15 The reactions are nucleophilic aromatic displacements and were conducted in DMAc at 155- 160°C with an excess of anhydrous potassium carbonate. After 3 to 6 h of reaction, high-molecular-weight poly(ketone)s are obtained in high yields. 

A powerful and efficient method for the preparation of poly(ketone)s is the direct polycondensation of dicarboxylic acids with aromatic compounds or of aromatic carboxylic acids using phosphorus pentoxide/methanesulfonic acid (PPMA)16 or polyphosphoric acid (PPA)17 as the condensing agent and solvent. By applying both of these reagents to the synthesis of hexafluoroisopropylidene-unit-containing aromatic poly(ketone)s, various types of poly(ketone)s such as poly(ether ketone) (11), poly(ketone) (12), poly(sulfide ketone) (13), and poly-... 

To date, much effort has been undertaken to develop new alternatives. For example, sulfonated aromatic polymers, i.e., polymers with the sulfonic acid groups directly attached to the main chain or carrying short pendant side chains with terminal sulfonic acid units, attract increasing interest because of their chemical and thermal stability, and the ease of the sulfonation procedure. Some of the proposed polymers are sulfonated polysulfone (SPSU) [134] sulfonated poly(phenylene oxide) (SPPO) [135] sulfonated poly-(ether ether ketone) (SPEEK) [136] poly(phenylquinoxaline) (PPQ) [137] and poly(benzeneimidazole) (PBI) [138],... 

Aromatic halides react with crown ether-complexed K02 by an electron-transfer mechanism and not by nucleophilic attack, as was shown by Frimer and Rosenthal (1976) using esr spectroscopy. The corresponding phenol is the main reaction product (Yamaguchi and Van der Plas, 1977). Esters are saponified by the K02/18-crown-6 complex in benzene, presumably by an addition-elimination pathway (San Fillippo et al., 1976). The same complex has been used to cleave cr-keto-, or-hydroxy-, and or-halo-ketones, -esters, and -carboxylic acids into the corresponding carboxylic acids in synthetically useful quantities (San Fillippo et al., 1976). 

Another concern for polystyrene- and some aromatic-based PEMs is hydrolysis of fhe sulfonic acid group from aromatic rings as well as hydrolytic cleavage of polymer backbone under fuel cell conditions for aromafic polymers including polyimides, poly(arylene ethers), poly(ether ketones), and poly(ether sulfones). It is well known that the sulfonation of aromafic rings is a reversible process especially at low pH and at elevated temperature (Scheme 3.3). The reversibility of sulfonation, for example, is used in fhe preparafion of trinitrotoluene or picric acid. Por the simplest membrane of the class of arylsulfonic acids (i.e., benzenesulfonic acid), fhe reacfion occurs upon freatment with a stream of superheated steam at 180°C.i ... 

---