Aqueous ethanol

Glutelins. Also insoluble in water and in 7% aqueous ethanol. Soluble in acids and alkalis. Also found in cereals. 

To prepare acetic acid, aqueous ethanol is added gradually to a hot mixture of aqueous sodium dichromate and sulphuric acid. The oxidising mixture is now always in excess, and therefore the oxidation proceeds as far as possible moreover, the reaction is carried out under reflux, so that any acetaldehyde which volatilises is returned to the oxidising mixture. Hence the final product contains only a small amount of acetaldehyde. 

Prepare a mixture of 30 ml, of aniline, 8 g. of o-chloro-benzoic acid, 8 g. of anhydrous potassium carbonate and 0 4 g. of copper oxide in a 500 ml. round-bottomed flask fitted with an air-condenser, and then boil the mixture under reflux for 1 5 hours the mixture tends to foam during the earlier part of the heating owing to the evolution of carbon dioxide, and hence the large flask is used. When the heating has been completed, fit the flask with a steam-distillation head, and stcam-distil the crude product until all the excess of aniline has been removed. The residual solution now contains the potassium. V-phenylanthrani-late add ca. 2 g. of animal charcoal to this solution, boil for about 5 minutes, and filter hot. Add dilute hydrochloric acid (1 1 by volume) to the filtrate until no further precipitation occurs, and then cool in ice-water with stirring. Filter otT the. V-phcnylanthranilic acid at the pump, wash with water, drain and dry. Yield, 9-9 5 g. I he acid may be recrystallised from aqueous ethanol, or methylated spirit, with addition of charcoal if necessary, and is obtained as colourless crystals, m.p. 185-186°. 

Many aromatic aldehydes (having the -CHO group joined directly to the benzene ring) undergo polymerisation when heated with a solution of potassium cyanide in aqueous ethanol. Thus benzaldehyde gives benzoin, a compound of double function, since it contains both a secondary alcoholic and a ketonic... 

Dissolve 8 8 g. (9 0 ml.) of cyclohexanone in 50 ml. of glacial acetic acid, add 8 ml. of phenylhydrazine, and boil the solution under reflux for 5 minutes. Cool the solution, when the tetrahydrocarbazole will crystallise out. Filter at the pump, drain well, and recrystallise either from aqueous ethanol or (better) from aqueous acetic acid. The recrystallisation should be performed rapidly, for the tetrahydrocarbazole undergoes atmO" spheric oxidation in hot solutions after recrystallisation, the compound should be dried in a vacuum desiccator and not in an oven. Repeated recrystallisation should be avoided. The tetrahydrocarbazole, after thorough drying, is obtained as colourless crystals, m.p. 118° yield of recrystallised material, 11 g. 

B) Phenacyl and p-Bromophenacyl esters. The sodium salt of an acid in aqueous-ethanolic solution will react with phenacyl bromide, CjHjCOCHgBr, and with p-bromophenacyl bromide, BrC,H4COCH2Br... 

Example. Dissolve 0 3 g. of />-chlorobenzoic ncid in a small quantity of warm ethanol (about 10 ml.), and ctlrefully add 5 o aqueous sodium hydroxide drop- wise until the solution is just pink to phenolphthalein. Evaporate to dryness on a water-bath. Dissolve the sodium -chlorobenzoate in a minimum of water, add a solution of 0-5 g. of phenacyl bromide in ethanol (about 5 ml.), and boil the mixture under reflux for i hour, and then cool. The phenacyl ester usually ciy stallises on cooling if it does not, add water dropnise with stirring to the chilled solution until separation of the ester just begins. Filter the ester, wash on the filter with water, drain and recrystallise from ethanol m.p. 90 . The /)-bromophenacyl ester is similarly prepared, and after recrystallisation from aqueous ethanol has m.p. 128 . (M.ps., pp. 543-545.)... 

C) Phenacyl and p-Bromophenacyl esters. Ammonium salts in aqueous-ethanolic solution do not however usually condense satisfactorily with phenacyl and />-bromophenacyl bromide. The aqueous solution of the ammonium salt should therefore be boiled with a slight excess of sodium hydroxide to remove ammonia, and the solution then cooled, treated with hydrochloric acid until just alkaline to phenol-phthalein, and then evaporated to dryness. The sodium salt is then treated as described (p. 349) to give the ester. Filter the ester, and wash with water to remove senium halide before recrystallisation. 

Sulphonamides. Mix together 1 0 g. of the dry acid or 1 - 2 g. of the anhydrous salt with 2 5 g. of phosphorus pentachloride f and heat under a reflux condenser in an oil bath at 150° for 30 minutes. Cool the mixture, add 20 ml. of dry benzene, warm on a steam bath and stir the solid mass well to extract the sulphonyl chloride filter. Add the benzene solution slowly and with stirring to 10 ml. of concentrated ammonia solution. If the sulphonamide precipitates, separate it by filtration if no solid is obtained, evaporate the benzene on a steam bath. Wash the sulphonamide with a little cold water, and recrystallise from water, aqueous ethanol or ethanol to constant m.p. 

Chlorodiphenyl. Diazotise 32 g. of o-chloroaniline (Section IV,34) in the presence of 40 ml. of concentrated hydrochloric acid and 22 -5 ml. of water in the usual manner (compare Section IV,61) with concentrated sodium nitrite solution. Transfer the cold, filtered diazonium solution to a 1 5 htre bolt-head flask surrounded by ice water, introduce 500 ml. of cold benzene, stir vigorously, and add a solution of 80 g. of sodium acetate trihydrate in 200 ml. of water dropwise, maintaining the temperature at 5-10°. Continue the stirring for 48 hours after the first 3 hours, allow the reaction to proceed at room temperature. Separate the benzene layer, wash it with water, and remove the benzene by distillation at atmospheric pressure distil the residue under reduced pressure and collect the 2-chlorodiphenyl at 150-155°/10 mm. The yield is 18 g. Recrystalliae from aqueous ethanol m.p. 34°. 

Indole (I) condenses with formaldehyde and dimethylamine in the presence of acetie acid (Mannich reaction see Section VI,20) largely in the 3-position to give 3 dimethylaminomethylindole or gramine (II). The latter reaets in hot aqueous ethanol with sodium cyanide to give the nitrile (III) upon boiling the reaction mixture, the nitrile undergoes hydrolysis to yield 3-indoleaeet-amide (IV), part of which is further hydrolysed to 3-indoleacetic acid (V, as sodium salt). The product is a readily separable mixture of 20 per cent, of (IV) and 80 per cent, of (V). 

Breslow studied the dimerisation of cyclopentadiene and the reaction between substituted maleimides and 9-(hydroxymethyl)anthracene in alcohol-water mixtures. He successfully correlated the rate constant with the solubility of the starting materials for each Diels-Alder reaction. From these relations he estimated the change in solvent accessible surface between initial state and activated complex " . Again, Breslow completely neglects hydrogen bonding interactions, but since he only studied alcohol-water mixtures, the enforced hydrophobic interactions will dominate the behaviour. Recently, also Diels-Alder reactions in dilute salt solutions in aqueous ethanol have been studied and minor rate increases have been observed Lubineau has demonstrated that addition of sugars can induce an extra acceleration of the aqueous Diels-Alder reaction . Also the effect of surfactants on Diels-Alder reactions has been studied. This topic will be extensively reviewed in Chapter 4. 

We chose benzyli dene acetone (4.39, Scheme 4.11) as a model dienophile for our studies. The uncatalysed Diels-Alder reaction of this compound with cyclopentadiene is slow, justifying a catalytic approach. Reaction of 4.39 with paraformaldehyde and dimethyl amine under acidic conditions in an aqueous ethanol solution, following a literature procedure, produced the HCl salt of 4.42 (Scheme 4.11). The dienophile was liberated in situ by adding one equivalent of base. 

In another attempt to achieve efficient coordination, we have used a strongly chelating diamine (4.43) in the Mannich reaction with 4.39 (Scheme 4.12). The reaction was performed in aqueous ethanol, producing 4.44-2HC1 in 64% yield. 

Finally, in the last step, the chelating auxiliary had to be removed Ideally, one would like to convert 4.54 into ketone 4.55 via a retro Mannich reaction. Unfortunately, repeated attempts to accomplish this failed. These attempts included refluxing in aqueous ethanol under acidic and basic conditions and refluxing in a 1 1 acetone - water mixture in the presence of excess paraformaldehyde under acidic conditions, in order to trap any liberated diamine. Tliese procedures were repeated under neutral conditions in the presence of copper(II)nitrate, but without success. 

A single organic product was obtained when 1 bromo 3 chloro propane was allowed to react with one molar equivalent of sodium cyanide in aqueous ethanol What was this product j... 

Under conditions of photochemical chlorination (CH3)3CCH2C(CH3)3 gave a mixture of two monochlorides in a 4 1 ratio The structures of these two products were assigned on the basis of their SnI hydrolysis rates in aqueous ethanol The major product (compound A) underwent hydrolysis much more slowly than the minor one (compound B) Deduce the structures of com pounds A and B... 

When 1 2 dibromodecane was treated with potassium hydroxide m aqueous ethanol it yielded a mixture of three isomenc compounds of molecular formula CioHi9Br Each of these compounds was converted to 1 decyne on reaction with sodium amide m dimethyl sulfoxide Men tify these three compounds... 

As actually carried out the mixed aldol condensation product 1 3 diphenyl 2 propen 1 one has been isolated in 85% yield on treating benzaldehyde with ace tophenone in an aqueous ethanol solution of sodium hydroxide at 15-30°C... 

Difluoroethanol [359-13-7], F2CHCH2OH, is a colorless Hquid with an alcohol-like odor mp, 28.2°C, bp, 96°C d[, 1.3084 n], 1.3320 heat of combustion, —1026 kJ/mol(—245.3 kcal/mol). It is stable to distillation and miscible with water and many organic solvents. As expected, its acidity Hes between that of 2-fluoroethanol and 2,2,2-trifluoroethanol both ia the gas phase (25) and ia 50% aqueous ethanol solution (26), where its of 1.0 x 10 is about 4.8 times smaller than that of trifluoroethanol. 

Lead nitrate [10099-74-8] Pb(N02)2, mol wt 331.23, sp gr 4.53, forms cubic or monoclinic colorless crystals. Above 205°C, oxygen and nitrogen dioxide are driven off, and basic lead nitrates are formed. Above 470°C, lead nitrate is decomposed to lead monoxide and Pb O. Lead nitrate is highly soluble in water (56.5 g/100 mL at 20°C 127 g/100 mL at 100°C), soluble in alkalies and ammonia, and fairly soluble in alcohol (8.77 g/100 mL of 43% aqueous ethanol at 22°C). Lead nitrate is readily obtained by dissolving metallic lead, lead monoxide, or lead carbonate in dilute nitric acid. Excess acid prevents the formation of basic nitrates, and the desired lead nitrate can be crystallized by evaporation. 

In some instances a carbon-carbon bond can be formed with C-nucleophiles. For example, 3-carboxamido-6-methylpyridazine is produced from 3-iodo-6-methylpyridazine by treatment with potassium cyanide in aqueous ethanol and l,3-dimethyl-6-oxo-l,6-dihydro-pyridazine-4-carboxylic acid from 4-chloro-l,3-dimethylpyridazin-6-(lH)-one by reaction with a mixture of cuprous chloride and potassium cyanide. Chloro-substituted pyridazines react with Grignard reagents. For example, 3,4,6-trichloropyridazine reacts with f-butyl-magnesium chloride to give 4-t-butyl-3,5,6-trichloro-l,4-dihydropyridazine (120) and 4,5-di-t-butyl-3,6-dichloro-l,4-dihydropyridazine (121) and both are converted into 4-t-butyl-3,6-dichloropyridazine (122 Scheme 38). 

Only 2-alkylthiopyrimidines are made by the Principal Synthesis, using 5-alkylthiourea as one component. For example, ethoxymethylenemalononitrile (877) and 5-benzylthiourea in aqueous acetone at 20 °C give 4-amino-2-benzylthiopyrimidine-5-carbonitrile (878) (61JOC79) and ethyl 2-allyl-2-formylacetate and 5-methylthiourea in aqueous ethanolic alkali give 5-allyl-2-methylthiopyrimidin-4(3H)-one (6UOC4425). 

Rate data are also available for the solvolysis of l-(2-heteroaryl)ethyl acetates in aqueous ethanol. Side-chain reactions such as this, in which a delocalizable positive charge is developed in the transition state, are frequently regarded as analogous to electrophilic aromatic substitution reactions. In solvolysis the relative order of reactivity is tellurienyl> furyl > selenienyl > thienyl whereas in electrophilic substitutions the reactivity sequence is furan > tellurophene > selenophene > thiophene. This discrepancy has been explained in terms of different charge distributions in the transition states of these two classes of reaction (77AHC(21)119>. 

Dimethyl sulfate in basic medium Methyl iodide in a sealed tube Methyl iodide in aqueous ethanolic potash Dimethyl sulfate in basic medium... 

Sodium or potassium hydrogen sulfite reacts with several thiiranes to give disulfides of /3-mercaptosulfonic acid salts (76EGP122086). Potassium thiocyanate in dimethylformamide or aqueous ethanol isomerizes thiiranes (Scheme 84) (72CJC3930). 1,2-Dithiols are obtained by treatment of thiiranes with NaBH2S3 obtained from sodium borohydride and sulfur (73TL1401). 

Benzyl-5-(2-hydroxyethyl)-4-inethyl-l,3-thia2ol1iim chloride. The product was isolated by pouring the ethanolic solution into well-stirred, ice-cold water, filtering, and recrystallizing from aqueous ethanol. The solutions should be ice-cold for the isolation of the low-melting acyloins. The products may also be Isolated by extraction as described for butyroin. 

Since the pure material melts at 144°, the product needs no further purification for ordinary purposes. It has a faint odor, which can be removed by recrystallization from aqueous ethanol (suitably by solution in 8-10 ml. of ethanol per gram of material and the addition of water just short of precipitation from the hot solution). The loss in rccrystallization is only about 5% the melting point is unchanged. 

Hydrolysis of the ester is achieved by refluxing in aqueous N or 2N NaOH solution until the insoluble ester dissolves. The solution is then cooled, and the alcohol is extracted into a suitable solvent, e.g. ether, toluene or alcohol-free chloroform. The extract is dried (CaS04, MgS04) and distilled, then fractionally distilled if liquid or recrystallised if solid. (The p-nitrobenzoic acid can be recovered by acidification of the aqueous layer.) In most cases where the alcohol to be purified can be readily extracted fi-om ethanol, the hydrolysis of the ester is best achieved with N or 2N ethanolic NaOH or 85% aqueous ethanolic N NaOH. The former is prepared by dissolving the necessary alkali in a minimum volume of water and diluting with absolute alcohol. The ethanolic solution is refluxed for one to two hours and hydrolysis is complete when an aliquot gives a clear solution on dilution with four or five times its volume of water. The bulk of the ethanol is distilled off and the residue is... 

---