Amine, tris ethyl

In this case furoin crystallized from the ethanolic solution upon cooling. The following somewhat simpler procedure may also be used. A solution of 13.4 g (0.05 mol) of catalyst, 96.1 g (1.0 moll of 2-furaldehyde, 300 mL of absolute ethanol, and 30.3 g (0.3 mol) of tri ethyl amine is stirred at room temperature for 12 hr. The product (84.5 g, 88%) crystallizes directly from solution and is isolated by filtration. 

C. Thiete 1,1-dioxide. A sample of 3-chlorothietane l,l-d1ox1de (8.0 g, 0.057 mol) Is dissolved In dry toluene (300 ml) (Note 7) In a 500-mL, twonecked, round-bottomed flask equipped with a reflux condenser, magnetic stirrer, heating mantle (or silicone oil bath), and thermometer. The reaction Is heated to 60° C and tri ethyl amine (28.7 g, 0.28 mol, 39,5 ml) Is added through the condenser. The reaction mixture Is stirred for 4 hr and triethyl-amine hydrochloride is removed by filtration and washed with toluene (100 mL), Toluene is removed on a rotary evaporator and the residue is recrystallized from diethyl ether-ethanol (Note 8) to give a white solid (4.5-4.8 g, 75-81 ) mp 49-50°C (llt mp 52-54°C). 

Zincate reagents can add to imines with or without Lewis acid catalysis. Alkylimines require BF3 but imines of pyridine-2-carboxaldehyde react directly. If the imines are derived from chiral amines, diastereoselectivity is observed. Both a-phenylethyl amine and ethyl valinate have been tried. Higher enantioselectivity was observed with mixed magnesium reagents.175... 

Isomerization of the epoxide (IV) with pyrrolidine was carried out as described by Sih (8) and consistently gave yields of 35-60% rather than the 73% reported. Changes in experimental conditions including longer reaction times at lower temperatures, use of freshly distilled pyrrolidine, use of NaOH dried pyrrolidine, and use of distilled epoxide (IV) had little effect on the yield. The only variation that improved the yield was to allow the reaction to proceed at ambient temperature for a longer period of time than the recommended 3 hours. Allowing the reaction to proceed for 40 hours provided a maximum 67.5% yield. Other bases such as sodium carbonate, tri ethyl amine, diethylamine l,5-diazabicyclo[4.3.0]non-5-ene(DBN), and sodium methoxide all gave lower yields of distilled product than pyrrolidine. It is important to use the hydroxyaldehyde (V) as soon as possible since it is a very unstable material. 

Amine Tris-[2-pentafluoroethoxy-tetrafluoro-ethyl]- ElOa, 49 (Toxicity)... 

The silyl enol ether may be obtained from the Fluka Chemical Corp., 255 Oser Avenue, Hauppauge, NY 11788. Alternatively, it may be prepared by the following modification of the procedure of Walshe and co-workers.2 The Walshe procedure is followed exactly with 36 g (0.30 mol) of acetophenone, 41.4 g (0.41 mol) of tri ethyl amine, 43.2 g (0.40 mol) of chlorotri-methylsilane, 60 g (0.40 mol) of sodium iodide, and 350 nt of acetonitrile. After extraction, the organic layer is dried over potassium carbonate and then concentrated with a rotary evaporator under reduced pressure. The crude product is a mixture of 97% of the desired silyl enol ether and 3% of acetophenone, as shown by gas chromatography. The crude product is distilled in a Claisen flask at a pressure of about 40 mm. After a small forerun (ca. 3... 

The procedure may be conducted on a larger scale in which case the proportion of catalyst and base are reduced. The submitters report that they obtained 169 g (78%) of butyroln from 216.3 g (3.0 mol) of butyraldehyde, 26.8 (0.1 mol) of thiazolium catalyst, 60.6 g (0.6 mol) of tri ethyl amine, and 600 mL of absolute ethanol. Although the scale may be increased further, appropriate precautions should be taken to control the reaction. For example, the aldehyde may be added in portions or the flask may be cooled initially. 

Bisphenol A (chemically similar to MDA but having -OH groups rather than amine groups) was identified in the water and 3% acetic extracts from Sample 2. Bisphenol A was not detected in the extracts from Sample 1. Infrared transmission spectra recorded through Samples 1 and 2 showed that the MDl isocyanate was slower to react in Sample 2 and so the bisphenol A could possibly relate to the laminating adhesive. As a result, LC-MS tests were undertaken later in the research, on extracts from Sample 3 (laminated with the same adhesive) specifically looking for bisphenol A - none was detected. Tri-ethyl phosphate, thought to be used as a cure catalyst, was identified in the extracts from both Sample 1 and Sample 2. 

UDMH is known to be miscible with the following wafer, benzene, triethyl benzene, toluene, kerosene, ethyl alcohol, isobutyl alcohol, n-butyl ether, n-amyl ether, n-hexyl ether, diethyl ether, petroleum ether, petroleum naphtha, n-heptane, n-hexane, n-octane, n-decane, n-dodecane, n hexadecane, cyclohexane, 1,2-dimethyl cyclohexane, phenyl cyclohexane, n-tetradecane, trichloroethylene, dichloroethylene, perch oroethylene, 1,1,1 -t richloroe thane, tri-ethyl amine, ethylenediamine, diethylene triamine, acetonitrile, aniline, cumene, tetra-hydronaphtnaiene, tetraethylene pentamine, ethylene glycol and hydrazine (Ref 4)... 

We report here the syntheses of the symmetric type 1 ligands tris[2-(diphen-ylphosphino)ethyl]amine, tris[2-(diphenylarsino)ethyl]amine, and tris[2-(meth-ylthio)ethyl]amine. 

The photoreactions of ethyl acetoacetate in water have been studied. " Irradiation of the butanethioates (249) yields products via various free radical paths.Electron-transfer-induced coupling has been reported in the reactions of tertiary amines (tri-n-propyl or tri-n-butyl) with tris(pentane-2,4-dionate)cobalt(iii). ° The products obtained in moderate to good yields from the reaction were identified as the dihydrofurans (250). Analogous products were obtained using the enamines (251), thereby indicating the possible involvement of such species in the initial reaction. 

Amino-5-carboxypyrazine in anhydrous dimethylformamide with triethyl-amine and ethyl chloroformate and then diethyl glutamate and stirred at room temperature gave 2-amino-5-(l, 3 -diethoxycarbonylpropyl)carbamoylpyrazine (24) (1244). Similarly a mixture of 2-carboxypyrazine and triethylamine in methylene dichloride with ethyl chloroformate and morpholine gave 2-( -morpholinocarbonyl)-pyrazine (1351). 2-Carboxy-3-hydroxypyrazine refluxed with phosphorus tris(A-methylanilide) in toluene gave 2-hydroxy-3-(A-methyl-A-phenyIcarbamoyl)pyrazine (1055), and 2-hydroxy-3-(A -methyl-A -p-tolylcarbamoyl)pyrazine was prepared similarly (1055). Tetracarboxypyrazine heated with sulfur tetrafluoride (SF4) at 150° gave tetra(trifluoromethyl)pyrazine (899). 

This is achieved by using monomers of the corresponding nature (nitroethylene and vinylidene cyanide are polymerized only anionically, whereas acrylonitrile and methyl methacrylate polymerize by both anionic and free-radical mechanisms) and by carrying out polymerization in solvents whose molecules contain electron-donating groups (atoms) or an unshared electron pair (dimethyl formamide, tri ethyl amine, isopropylamine, tetrahydrofuran, acetone, ethylpropyl ketone, etc.). 

---