Acyclic alkenes, reaction with

Of course, even in the case of acyclic alkenes reaction enthalpy is not exactly zero, and therefore the product distribution is never completely statistically determined. Table V gives equilibrium data for the metathesis of some lower alkenes, where deviations of the reaction enthalpy from zero are relatively large. In this table the ratio of the contributions of the reaction enthalpy and the reaction entropy to the free enthalpy of the reaction, expressed as AHr/TASr, is given together with the equilibrium distribution. It can be seen that for the metathesis of the lower linear alkenes the equilibrium distribution is determined predominantly by the reaction entropy, whereas in the case of the lower branched alkenes the reaction enthalpy dominates. If the reaction enthalpy deviates substantially from zero, the influence of the temperature on the equilibrium distribution will be considerable, since the high temperature limit will always be a 2 1 1 distribution. Typical examples of the influence of the temperature are given in Tables VI and VII. 

Acyclic S-S dications 51 and 52 also give 1,2-disulfonium salts 90 in reactions with olefins.79 Formation of a mixture of diastereomers is observed in the case of 1,2-disubstituted alkenes. Reaction with conjugated dienes leads exclusively to the product of 1,4-addition 89 as mixtures of E- and Z-products whose ratio depends on steric factors (Scheme 34).79... 

The stereochemistry of 43 (38) is easy to see because the cyclohexane ring cannot rotate about individual C-C bonds. Does this same stereochemical bias occur with acyclic alkenes When an acyclic alkene reacts with a halogen, the product is an acyclic dihalide, and free rotation is possible about those bonds. However, the answer is yes Acyclic alkenes react with the same stereochemical bias because the mechanism of reaction of an alkene and diatomic halogen is the same for both acyclic and cyclic alkenes. This selectivity is demonstrated with the simple acyclic alkene, 2-butene however, an analysis requires an examination of each stereoisomer, cts-2-butene and rans-2-butene (see Chapter 9, Section 9.4). When cts-2-butene reacts with bromine, the product is a racemic mixture, (2S,3iS)-dibromobutane along with (2i2,3i2)-dibromobutane (see 44). Two new stereogenic centers are created by this reaction. (See Chapter 9, Section 9.3, to review absolute configuration.) When rans-2-butene reacts with bromine, however, the product is a racemic mixture of (2S,3i2)-dibromobutane and (2i ,3S)-dibromobutane (see 45), which are drawn a second time as the eclipsed rotamer (Chapter 8, Section 8.1) to show their relationship to 44. Dibromides 44 and 45 are diastereomers (Chapter 9, Section 9.5). 

Enol ethers are more reactive toward formaldehyde and MesAl than simple alkenes. Reaction with dihydropyran gives a 75% yield of a 92 8 mixture of 33 and 34 (See Figure 10). The major product is again formed by cis addition of hydroxymethyl and methyl groups. Quite different results are obtained with acyclic enol ethers. 20 Reaction of ethyl propenyl ether, as a 78 22 cis-trans mixture, with 2 equivalents of paraformaldehyde and 2 equivalents of MesAl at 0 in CH2CI2 gives a 65% yield of an 18 1 mixture of threo- and c yr/ir< -3-ethoxy-2-meAyl-l-butanol (37 and 38). Identical results are obtained from either pure stereoisomer of ethyl propenyl ether. 

Electron deficient carbon-carbon double bonds are resistant to attack by the electrophilic reagents of Section 5.05.4.2.2(t), and are usually converted to oxiranes by nucleophilic oxidants. The most widely used of these is the hydroperoxide ion (Scheme 79). Since epoxidation by hydroperoxide ion proceeds through an intermediate ct-carbonyl anion, the reaction of acyclic alkenes is not necessarily stereospecific (Scheme 80) (unlike the case of epoxidation with electrophilic agents (Section 5.05.4.2.2(f)) the stereochemical aspects of this and other epoxidations are reviewed at length in (B-73MI50500)). 

Cycloaddition reactions also have important applications for acyclic chalcogen-nitrogen species. Extensive studies have been carried out on the cycloaddition chemistry of [NSa]" which, unlike [NOa]", undergoes quantitative, cycloaddition reactions with unsaturated molecules such as alkenes, alkynes and nitriles (Section 5.3.2). ° The frontier orbital interactions involved in the cycloaddition of [NSa]" and alkynes are illustrated in Fig. 4.13. The HOMO ( Tn) and LUMO ( r ) of the sulfur-nitrogen species are of the correct symmetry to interact with the LUMO (tt ) and HOMO (tt) of a typical alkyne, respectively. Although both... 

It has been suggested that these polymers are mainly linear, which may be a consequence of intermolecular metathesis reactions with traces of acyclic alkenes, or of other consecutive reactions 19-22). 

Mutual metathesis of a cyclic and an acyclic alkene provides still more possibilities in synthesizing organic compounds. For instance, cycloalkenes are cleaved by ethene into a,co-dienes. The reaction of 1,5-cyclooctadiene with ethene gives 1,5,9-decatriene (18) norbornene reacts with 2-butene to yield 1,3-dipropenylcyclopentane (30) ... 

The preferred kinetic model for the metathesis of acyclic alkenes is a Langmuir type model, with a rate-determining reaction between two adsorbed (complexed) molecules. For the metathesis of cycloalkenes, the kinetic model of Calderon as depicted in Fig. 4 agrees well with the experimental results. A scheme involving carbene complexes (Fig. 5) is less likely, which is consistent with the conclusion drawn from mechanistic considerations (Section III). However, Calderon s model might also fit the experimental data in the case of acyclic alkenes. If, for instance, the concentration of the dialkene complex is independent of the concentration of free alkene, the reaction will be first order with respect to the alkene. This has in fact been observed (Section IV.C.2) but, within certain limits, a first-order relationship can also be obtained from many hyperbolic models. Moreover, it seems unreasonable to assume that one single kinetic model could represent the experimental results of all systems under consideration. Clearly, further experimental work is needed to arrive at more definite conclusions. Especially, it is necessary to investigate whether conclusions derived for a particular system are valid for all catalyst systems. 

Inverse electron-demand Diels-Alder reaction of (E)-2-oxo-l-phenylsulfo-nyl-3-alkenes 81 with enolethers, catalyzed by a chiral titanium-based catalyst, afforded substituted dihydro pyranes (Equation 3.27) in excellent yields and with moderate to high levels of enantioselection [81]. The enantioselectivity is dependent on the bulkiness of the Ri group of the dienophile, and the best result was obtained when Ri was an isopropyl group. Better reaction yields and enantioselectivity [82, 83] were attained in the synthesis of substituted chiral pyranes by cycloaddition of heterodienes 82 with cyclic and acyclic enolethers, catalyzed by C2-symmetric chiral Cu(II) complexes 83 (Scheme 3.16). 

A more practical, atom-economic and environmentally benign aziridination protocol is the use of chloramine-T or bromamine-T as nitrene source, which leads to NaCl or NaBr as the sole reaction by-product. In 2001, Gross reported an iron corrole catalyzed aziridination of styrenes with chloramine-T [83]. With iron corrole as catalyst, the aziridination can be performed rmder air atmosphere conditions, affording aziridines in moderate product yields (48-60%). In 2004, Zhang described an aziridination with bromamine-T as nitrene source and [Fe(TTP)Cl] as catalyst [84]. This catalytic system is effective for a variety of alkenes, including aromatic, aliphatic, cyclic, and acyclic alkenes, as well as cx,p-unsaturated esters (Scheme 28). Moderate to low stereoselectivities for 1,2-disubstituted alkenes were observed indicating the involvement of radical intermediate. 

Some hydrometalation reactions have been shown to be catalyzed by zirconocene. For instance, CpiZrCf-catalyzed hydroaluminations of alkenes [238] and alkynes [239] with BU3AI have been observed (Scheme 8-34). With alkyl-substituted internal alkynes the process is complicated by double bond migration, and with terminal alkynes double hydrometalation is observed. The reaction with "PrjAl and Cp2ZrCl2 gives simultaneously hydrometalation and C-H activation. Cp2ZrCl2/ BuIi-cat-alyzed hydrosilation of acyclic alkenes [64, 240] was also reported to involve hydrogen transfer via hydrozirconation. 

Reactions with Acylium Ions. Alkenes react with acyl halides or acid anhydrides in the presence of a Lewis acid catalyst to give (3,y-unsaturated ketones. The reactions generally work better with cyclic than acyclic alkenes. 

Reactions with alkenes and nonconjugated dienes have been described in many publications (101, 103, 106-111). Various alkenes, such as cycloalkenes as well as acyclic alkenes, up to tetrasubstituted derivatives, can react with nitroalkenes (42) (110). Only one double bond is involved in the reactions of heterodienes (42) with nonconjugated dienes (111), whereas the second double bond can be used in subsequent transformations of target nitronates (35). The reactions of heterodienes (42) with inactivated alkenes require the presence of LA as catalyst. 

Alkyl Nitronates In spite of the low stability of acyclic alkyl nitronates, these compounds were rather extensively studied in [3 + 2]-addition reactions with various alkenes (9, 18, 28, 49, 300, 301, 306, 307, 338b-354) (Chart 3.11). 

The alkylation of olefinic G-H bonds proceeds when conjugated enones are employed in the ruthenium-catalyzed reaction with alkenes, as shown in Equation (16).1 7 Among the acylcyclohexenes, 1-pivaloyl-l-cyclohexene exhibits a high reactivity and the presence of an oxygen atom at the allylic position in the six-membered ring increases the reactivity of the enones. Some terminal olefins, for example, triethoxyvinylsilane, allyltrimethylsilane, methyl methacrylate, and vinylcyclohexane, are applicable for the alkylation of the olefinic C-H bonds. Acyclic enones also undergo this alkylation. 

The first published report on the use of this catalyst for the cross-metathesis of functionalised acyclic alkenes was by Blechert and co-workers towards the end of 1996 [37]. This report was also noteworthy for its use of polymer-bound alkenes in the cross-metathesis reaction. Tritylpolystyrene-bound AT-Boc N-al-lylglycinol 18 was successfully cross-metathesised with both unfunctionalised alkenes and unsaturated esters (Eq. 17) (Table 1). 

The ring-opening cross-metathesis reaction is similar to the acyclic cross-metathesis reaction discussed above, except that one of the acyclic alkenes is replaced with a strained cyclic alkene (Scheme 5). 

The sterically bulky ruthenium alkylidene 42, formed via ring-opening of the cyclobutene, should react more rapidly with the terminal alkene than with a second molecule of the cyclobutene. This preference for reacting with the acyclic alkene is probably due to a combination of the greater steric hindrance of the cyclic alkene and the ability of the reaction with the terminal alkene to proceed... 

Successful ring-opening cross-metathesis with symmetrical internal acyclic alkenes was, however, achieved by Blechert and Schneider [49]. Reaction of a variety of functionalised norbornene derivatives with fraws-hex-3-ene in the presence of the ruthenium vinylalkylidene catalyst 4 yielded the ring-opened products as predominantly trans-trans isomers (for example Eq. 33). 

A subsequent publication by Blechert and co-workers demonstrated that the molybdenum alkylidene 3 and the ruthenium benzylidene 17 were also active catalysts for ring-opening cross-metathesis reactions [50]. Norbornene and 7-oxanorbornene derivatives underwent selective ring-opening cross-metathesis with a variety of terminal acyclic alkenes including acrylonitrile, an allylsilane, an allyl stannane and allyl cyanide (for example Eq. 34). 

The most selective - and also most general - titanocene catalyst is complex 35 d, also studied by Buchwald and coworkers. This catalyst was used to hydrogenate a variety of functionalized and unfunctionalized cyclic and acyclic alkenes with excellent ee-values in most cases [46]. Enamines could also be hydrogenated with enantiomeric excesses of 80-90% [47]. However, high catalyst loadings (5-8 mol%) and long reaction times were required to drive the reactions to completion. 

Af-Acyliminium ions are known to serve as electron-deficient 4n components and undergo [4+2] cycloaddition with alkenes and alkynes.15 The reaction has been utilized as a useftil method for the construction of heterocycles and acyclic amino alcohols. The reaction can be explained in terms of an inverse electron demand Diels-Alder type process that involves an electron-deficient hetero-diene with an electron-rich dienophile. Af-Acyliminium ions generated by the cation pool method were also found to undergo [4+2] cycloaddition reaction to give adduct 7 as shown in Scheme 7.16 The reaction with an aliphatic olefin seems to proceed by a concerted mechanism, whereas the reaction with styrene derivatives seems to proceed by a stepwise mechanism. In the latter case, significant amounts of polymeric products were obtained as byproducts. The formation of polymeric byproducts can be suppressed by micromixing. 

Using acyclic and cyclic N-tosylated iodomethylaziridines, Taguchi investigated annulation reactions [46]. The reaction with electron-rich alkenes such as enol ethers proceeds smoothly as illustrated in Scheme 18. 

Iodine was found to be an efficient catalyst for the aziridination of alkenes (Scheme 6) utilizing chloramine-T (A-chloro-A-sodio-p-toluenesulfonamide) as the nitrogen source. For example, when 2 equiv. of styrene (45a) were added to chloramine-T in the presence of a catalytic amount of iodine (10mol%) in a 1 1 solvent mixture of acetonitrile and neutral buffer, the corresponding aziridine (46) was obtained in 91% yield. The reaction proved to work with other acyclic and cyclic alkenes, such as oct-l-ene and cyclohexene. The aziridination of para-substituted styrene derivatives (45b-e) demonstrated that, as expected for an electrophilic addition, electron-rich alkenes reacted faster than electron-poor alkenes. However, with 1 equiv. of I2, mainly iodohydrin (47) was formed. A catalytic cycle has been proposed to account for the fact that only a catalytic amount of iodine is required (Scheme 1) ... 

---