Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Wet abrasion

The tendency of the strong, highly crystalline fibers to fibnUate, ie, to develop a hairy surface on wet-abrasion has, for the textile appUcations, been minimized by process changes both in fiber production and fabric manufacture. However, for nonwoven or speciaUty paper appUcations, this property can aUow potential users to develop ceUulosic microfibers during processing. [Pg.352]

The characteristics of interior paints that require testing and analysis include hiding and appearance, package stabiHty, adhesion, spatter resistance, flow and leveling, color and sheen uniformity, touch-up, stain removal, burnish resistance, and block and print resistance. A popular test that assesses the wet abrasion resistance of an interior paint is to measure its scmb resistance. A mechanical device is used to scmb a paint film of a specified thickness with a standard bmsh and abrasive cleanser suspension. The number of scmb cycles (back and forth movements of the weighted bmsh) at various end points (first cut through, or 50% removal of the film) is then recorded. Scmb resistance usually holds steady or decreases slightly as PVC is increased, but drops quickly once the CPVC is exceeded in a paint formulation. [Pg.546]

Cross-linked finishes are not permanent in the tme sense of the word however, under optimum conditions the finish can last for the usehil life of the material. Wet abrasion during laundering is probably the principal cause of gradual removal of the finish. In order to retain antistatic protection for extended use, an excess of finish is often appHed The extent of chemical interaction between the durable antistatic agents and the fiber substrates to which they are appHed is not perfectiy understood. Certain oxidizing agents such as hypochlorite bleaches tend to depolymerize and remove some durable antistatic finishes. Some of the durable finishes have also produced undesirable side effects on textile materials, ie, harsh hand, discoloration, and loss of tensile properties. [Pg.294]

Dry abrasive blast cleaning should be used on new steelwork where the main contaminant is mill scale. For heavily rusted and pitted steelwork, increased durability can be obtained by the use of wet abrasive blasting where this is practicable. The water will be more effective in removing the potentially destructive and corrosive soluble iron-corrosion products that form at the bottom of corrosion pits. [Pg.134]

After major surface contaminants have been removed, e.g. by wet abrasive blasting of hot-rolled structural steel, application of a thin coat of an etch primer greatly reduces the incidence of underfilm corrosion, presumably by eleminating localised areas of poor adhesion. Phosphate pretreatments followed by effective rinsing have a similar effect over cold reduced sheets. [Pg.618]

In the South African mining industry most processes for recovering precious metals, coal, minerals and diamonds are wet methods, involving the suspension of solids in water [1], In the control of such wet abrasive conditions in the pumping of fine particles size slurries, particle size separation in cyclones and in floatation cells, the choice of soft natural rubber lining is the most cost effective. [Pg.41]

Uses Monomer for adhesives, coatings, inks, photoresists, solder masks, photopolymers adhesion promoter on metal Features Difunctional good hardness, pigment wetting, abrasion resist., weatherability, hardness, abrasion resist., metal adhesion, pigment wetting low odor fast cure... [Pg.452]

The wet track abrasion test covers measurement of the wearing qualities of slurry seal under wet abrasion conditions. [Pg.313]

Abrasive treatments consist of scouring, machining, hand sanding, and dry and wet abrasive blasting. The abrasive medium can be fine sandpaper, carborundum or alumina abrasives, metal wools, or abrasive shot. Mechanical abrasion is usually preceded and followed by solvent cleaning. The choice is generally determined by available production facilities and cost. [Pg.442]


See other pages where Wet abrasion is mentioned: [Pg.432]    [Pg.105]    [Pg.135]    [Pg.616]    [Pg.618]    [Pg.638]    [Pg.1150]    [Pg.113]    [Pg.357]    [Pg.91]    [Pg.337]    [Pg.154]    [Pg.304]    [Pg.1211]    [Pg.223]    [Pg.48]    [Pg.40]    [Pg.41]    [Pg.41]    [Pg.230]    [Pg.150]    [Pg.556]    [Pg.574]    [Pg.508]    [Pg.856]    [Pg.856]    [Pg.413]    [Pg.645]    [Pg.647]    [Pg.667]    [Pg.265]    [Pg.865]    [Pg.1064]    [Pg.727]    [Pg.3]    [Pg.3]    [Pg.242]   
See also in sourсe #XX -- [ Pg.3 ]




SEARCH



Wet Abrasive Conditions

Wet abrasive blasting

Wet track abrasion test

© 2024 chempedia.info