Viscoelastic properties, temperature

In other work, the impact of thermal processing on linewidth variation was examined and interpreted in terms of how the resist s varying viscoelastic properties influence acid diffusion (105). The authors observed two distinct behaviors, above and below the resist film s glass transition. For example, a plot of the rate of deprotection as a function of post-exposure processing temperature show a change in slope very close to the T of the resist. Process latitude was improved and linewidth variation was naininiized when the temperature of post-exposure processing was below the film s T. 

Tensile Testing. The most widely used instmment for measuring the viscoelastic properties of soHds is the tensile tester or stress—strain instmment, which extends a sample at constant rate and records the stress. Creep and stress—relaxation can also be measured. Numerous commercial instmments of various sizes and capacities are available. They vary greatiy in terms of automation, from manually operated to completely computer controlled. Some have temperature chambers, which allow measurements over a range of temperatures. Manufacturers include Instron, MTS, Tinius Olsen, Apphed Test Systems, Thwing-Albert, Shimadzu, GRC Instmments, SATEC Systems, Inc., and Monsanto. 

For a fiber immersed in water, the ratio of the slopes of the stress—strain curve in these three regions is about 100 1 10. Whereas the apparent modulus of the fiber in the preyield region is both time- and water-dependent, the equiUbrium modulus (1.4 GPa) is independent of water content and corresponds to the modulus of the crystalline phase (32). The time-, temperature-, and water-dependence can be attributed to the viscoelastic properties of the matrix phase. 

Tackifying resins enhance the adhesion of non-polar elastomers by improving wettability, increasing polarity and altering the viscoelastic properties. Dahlquist [31 ] established the first evidence of the modification of the viscoelastic properties of an elastomer by adding resins, and demonstrated that the performance of pressure-sensitive adhesives was related to the creep compliance. Later, Aubrey and Sherriff [32] demonstrated that a relationship between peel strength and viscoelasticity in natural rubber-low molecular resins blends existed. Class and Chu [33] used the dynamic mechanical measurements to demonstrate that compatible resins with an elastomer produced a decrease in the elastic modulus at room temperature and an increase in the tan <5 peak (which indicated the glass transition temperature of the resin-elastomer blend). Resins which are incompatible with an elastomer caused an increase in the elastic modulus at room temperature and showed two distinct maxima in the tan <5 curve. 

In a fundamental sense, the miscibility, adhesion, interfacial energies, and morphology developed are all thermodynamically interrelated in a complex way to the interaction forces between the polymers. Miscibility of a polymer blend containing two polymers depends on the mutual solubility of the polymeric components. The blend is termed compatible when the solubility parameter of the two components are close to each other and show a single-phase transition temperature. However, most polymer pairs tend to be immiscible due to differences in their viscoelastic properties, surface-tensions, and intermolecular interactions. According to the terminology, the polymer pairs are incompatible and show separate glass transitions. For many purposes, miscibility in polymer blends is neither required nor de-... 

Thermal and thermomechanical analyses44 are very important for determining die upper and lower usage temperature of polymeric materials as well as showing how they behave between diose temperature extremes. An especially useful thermal technique for polyurethanes is dynamic mechanical analysis (DMA).45 Uiis is used to study dynamic viscoelastic properties and measures die ability to... 

Dynamic mechanical measurements for elastomers that cover wide ranges of frequency and temperature are rather scarce. Payne and Scott [12] carried out extensive measurements of /a and /x" for unvulcanized natural mbber as a function of test frequency (Figure 1.8). He showed that the experimental relations at different temperatures could be superposed to yield master curves, as shown in Figure 1.9, using the WLF frequency-temperature equivalence, Equation 1.11. The same shift factors, log Ox. were used for both experimental quantities, /x and /x". Successful superposition in both cases confirms that the dependence of the viscoelastic properties of rubber on frequency and temperature arises from changes in the rate of Brownian motion of molecular segments with temperature. 

Investigation of the linear viscoelastic properties of SDIBS with branch MWs exceeding the critical entanglement MW of PIB (about -7000 g/mol ) revealed that both the viscosity and the length of the entanglement plateau scaled with B rather than with the length of the branches, a distinctively different behavior than that of star-branched PIBs. However, the magnitude of the plateau modulus and the temperature dependence of the terminal zone shift factors were found to... 

In the molten state polymers are viscoelastic that is they exhibit properties that are a combination of viscous and elastic components. The viscoelastic properties of molten polymers are non-Newtonian, i.e., their measured properties change as a function of the rate at which they are probed. (We discussed the non-Newtonian behavior of molten polymers in Chapter 6.) Thus, if we wait long enough, a lump of molten polyethylene will spread out under its own weight, i.e., it behaves as a viscous liquid under conditions of slow flow. However, if we take the same lump of molten polymer and throw it against a solid surface it will bounce, i.e., it behaves as an elastic solid under conditions of high speed deformation. As a molten polymer cools, the thermal agitation of its molecules decreases, which reduces its free volume. The net result is an increase in its viscosity, while the elastic component of its behavior becomes more prominent. At some temperature it ceases to behave primarily as a viscous liquid and takes on the properties of a rubbery amorphous solid. There is no well defined demarcation between a polymer in its molten and rubbery amorphous states. 

An example of the utility of these expressions is given in Figure 1 where the log (real modulus) is plotted against temperature for two test specimens of EPDM. The first test specimen is represented by o s, while the second specimen is represented by the dashed lines, which are 95% confidence limits calculated from the expressions in Table II and it viscoelastic properties. The measurements were made three weeks apart. 

Suppose one wanted to compare the behavior of two polymers and their blends. Let us define the signal as the difference between the logarithims of the viscoelastic quantities and the noise as the error calculated for a specific set of viscoelastic properties associated with a specific composition. The signal to noise ratio would have the appearance of the three curves shown in Figure 2 for a PMMA/Hytrel blend >3/1. Selection of the optimum conditions for comparison is apparent in that figure. Emphasis should be placed at those temperatures with high signal/noise ratios. 

The SAS data files that wera created as a results of the operations noted earlier have the important property that all three viscoelatic properties have either been measured or interpolated to the same temperature. Therefore one can merge data sets for different polymers by temperature (a SAS data set manipulation) and then perform blend calculations on the data quite simply in SAS. For example, one can calculate the expected viscoelastic properties of a blend from the pure components and their volume fraction using the equations of Uemura and Takaynagi (8). 

In contrast to the mature instrumental techniques discussed above, a hitherto nonexistent class of techniques will require substantial development effort. The new instruments will be capable of measuring the thermal (e.g., glass transition temperatures for amorphous or semicrystalline polymers and melting temperatures for materials in the crystalline phase), chemical, and mechanical (e.g., viscoelastic) properties of nanoscale films in confined geometries, and their creation will require rethinking of conventional methods that are used for bulk measurements. 

Since the viscoelastic properties of the solid undergo a significant change as the solid undergoes a transition from the amorphous to rubbery states (due to elevation of temperature at constant moisture content or to an increase in moisture content at constant temperature), one also expects marked changes in the processing properties of these solids as this transition occurs. Some properties that are likely to be affected include tablet compaction [76], gelatin capsule... 

For quality cured thermoset resins, approximately one percent of the mass is soluble when subjected to long-term leaching with tetrahydrofuran. Equilibrium is approached in two weeks resin swell is not visually noticeable. The monomeric, chemical structures are such that the hydrocarbon resins exhibit more pronounced viscoelastic properties whereas, the epoxy resins are similar to elastic bodies when subjected to tensile testing at room temperature. Therein, LRF 216 is less sensitive to flaws and is more nonlinear in tensile or compressive stress-strain analysis. 

The understanding of the temperature and conversion dependence of the crosslinking kinetics is one of the prerequisites for understanding the changes in viscosity and viscoelastic properties as a function of reaction time and reaction temperature ( ). Three main factors determine these relations the reaction kinetics determined by temperature and conversion, the changes in structure determined primarily by conversion and the changes in Tg determined primarily also by conversion. 

Polymers are viscoelastic materials meaning they can act as liquids, the visco portion, and as solids, the elastic portion. Descriptions of the viscoelastic properties of materials generally falls within the area called rheology. Determination of the viscoelastic behavior of materials generally occurs through stress-strain and related measurements. Whether a material behaves as a viscous or elastic material depends on temperature, the particular polymer and its prior treatment, polymer structure, and the particular measurement or conditions applied to the material. The particular property demonstrated by a material under given conditions allows polymers to act as solid or viscous liquids, as plastics, elastomers, or fibers, etc. This chapter deals with the viscoelastic properties of polymers. 

According to the more widely used Williams, Landel, and Ferry (WLF) equations, all linear, amorphous polymers have similar viscoelastic properties at Tg and at specific temperatures above Tg, such as Tg + 25 K, and the constants Ci and C2 related to holes or free volume, the following relationship holds ... 

Williams, Landel, and Ferry equation (WLF) Used for predicting viscoelastic properties at temperatures above Tg when these properties are known for one specific temperature, yield point Point on a stress-strain curve below which there is reversible recovery. 

---