Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Tubing,treatment

Test Tube No. Contents of Tube Treatment Conclusion... [Pg.41]

If both As and Sb are present, the relative positions of the deposits establishes their identity the lower thermal stability of SbH3 means that it decomposes before ASH3 in the tube. Treatment of the residues with aqueous NaOCl also distinguishes them since only arsenic dissolves ... [Pg.397]

Figure 13.26 models the structure of the SWNT (52). Each hexagon represents a six-membered aromatic ring. While this drawing shows the end of the nanotube closed, it is not known for sure if or how they are closed. The end structure may vary with method of synthesis or tube treatments. [Pg.725]

The first function of a wellsite is to accommodate drilling operations. However, a wellsite must be designed to allow access for future operations and maintenance activity, and in many cases provide containment in the event of accidental emission. Production from a single wellhead or wellhead cluster is routed by pipeline to a gathering station, often without any treatment. In such a case the pipeline effectively becomes an extension of the production tubing. If a well is producing naturally or with assistance from a down... [Pg.260]

Keywords production decline, economic decline, infill drilling, bypassed oil, attic/cellar oil, production potential, coiled tubing, formation damage, cross-flow, side-track, enhanced oil recovery (EOR), steam injection, in-situ combustion, water alternating gas (WAG), debottlenecking, produced water treatment, well intervention, intermittent production, satellite development, host facility, extended reach development, extended reach drilling. [Pg.351]

Glass can be machined to a very limited extend only. Treatment of glass for the production of tubes is delicate and requires lots of special tools. The shape of the vacuum envelope can t be simply changed. Glass is more suitable for mass production of simple shaped goods. [Pg.533]

It is important to realize that the preceding treatment is the limiting one for sufficiently small tubes and that significant departures from the limiting Eq. II-10 occur for r/a values as small as O.OS. More realistically, the situation is as shown in Fig. II-9, and the maximum pressure may not be reached until is considerably greater than 90°. [Pg.17]

The simple treatment of this and of other electrokinetic effects was greatly clarified by Smoluchowski [69] for electroosmosis it is as follows. The volume flow V (in cm /sec) for a tube of radius r is given by applying the linear velocity V to the body of liquid in the tube... [Pg.185]

In order to save the cost of the distilling-flask (which after the above treatment is useless for further work), the mixture may be distilled from a small retort made by blowing a suitable bulb on the end of a rather thick-walled tube of about 8-10 mm. internal diameter the tube is then bent through almost 90° a few cm. above the bulb, cut to a suitable length, and the Open end fitted into the boiling ube as before. [Pg.213]

Fire retardant treatments Fire-tube furnace Fireworks... [Pg.403]

Shirakawa techmqi Shirlan Shirley Non-Lint AnalyZ Shi take mushroom Shock absorbers Shock absorption Shocking Shockley defects Shock treatment Shock tubes Shock waves Shoe components Shoe products Shoes... [Pg.883]

Other Continuous Processes. Various pasteurization heat treatments ate identified by names such as quick time, vacuum treatment (vacreator), modified tubular (Roswell), small-diameter tube (MaHotizer), and steam injection. The last three methods are ultrahigh temperature (UHT) processes (see Fig. 3). Higher treatment temperatures with shorter times, approaching two seconds, are preferred because the product has to be cooled quickly to prevent deleterious heat effects. [Pg.359]

Spent Fuel Treatment. Spent fuel assembhes from nuclear power reactors are highly radioactive because they contain fission products. Relatively few options are available for the treatment of spent fuel. The tubes and the fuel matrix provide considerable containment against attack and release of nucHdes. To minimi2e the volume of spent fuel that must be shipped or disposed of, consoHdation of rods in assembhes into compact bundles of fuel rods has been successfully tested. Alternatively, intact assembhes can be encased in metal containers. [Pg.229]


See other pages where Tubing,treatment is mentioned: [Pg.135]    [Pg.341]    [Pg.334]    [Pg.359]    [Pg.245]    [Pg.578]    [Pg.249]    [Pg.584]    [Pg.438]    [Pg.117]    [Pg.135]    [Pg.341]    [Pg.334]    [Pg.359]    [Pg.245]    [Pg.578]    [Pg.249]    [Pg.584]    [Pg.438]    [Pg.117]    [Pg.259]    [Pg.355]    [Pg.2066]    [Pg.18]    [Pg.418]    [Pg.164]    [Pg.963]    [Pg.156]    [Pg.108]    [Pg.401]    [Pg.420]    [Pg.95]    [Pg.461]    [Pg.573]    [Pg.111]    [Pg.98]    [Pg.98]    [Pg.196]    [Pg.223]    [Pg.64]    [Pg.190]    [Pg.194]    [Pg.194]    [Pg.119]    [Pg.5]    [Pg.7]    [Pg.324]   
See also in sourсe #XX -- [ Pg.134 , Pg.143 ]




SEARCH



© 2024 chempedia.info