SUBJECTS titanium

Metals can be precipitated from the Hquid or gas phase. For example, nickel ammonium carbonate gives nickel powder when subjected to hydrogen in an autoclave. Copper, cobalt, molybdenum, and titanium powders can also be formed by precipitation. 

Titanium is resistant to nitric acid from 65 to 90 wt % and ddute acid below 10 wt %. It is subject to stress—corrosion cracking for concentrations above 90 wt % and, because of the potential for a pyrophoric reaction, is not used in red filming acid service. Tantalum exhibits good corrosion resistance to nitric acid over a wide range of concentrations and temperatures. It is expensive and typically not used in conditions where other materials provide acceptable service. Tantalum is most commonly used in appHcations where the nitric acid is close to or above its normal boiling point. 

Analytical and Test Methods. o-Nitrotoluene can be analyzed for purity and isomer content by infrared spectroscopy with an accuracy of about 1%. -Nitrotoluene content can be estimated by the decomposition of the isomeric toluene diazonium chlorides because the ortho and meta isomers decompose more readily than the para isomer. A colorimetric method for determining the content of the various isomers is based on the color which forms when the mononitrotoluenes are dissolved in sulfuric acid (45). From the absorption of the sulfuric acid solution at 436 and 305 nm, the ortho and para isomer content can be deterrnined, and the meta isomer can be obtained by difference. However, this and other colorimetric methods are subject to possible interferences from other aromatic nitro compounds. A titrimetric method, based on the reduction of the nitro group with titanium(III) sulfate or chloride, can be used to determine mononitrotoluenes (32). Chromatographic methods, eg, gas chromatography or high pressure Hquid chromatography, are well suited for the deterrnination of mononitrotoluenes as well as its individual isomers. Freezing points are used commonly as indicators of purity of the various isomers. 

Certification of Colorants. A further distinction between color additives is made relative to whether there is requirement for FDA certification. In general, only synthetic organic colorants are now subject to certification, whereas natural organic and inorganic colorants, such as turmeric and titanium dioxide, are not. The exemption from certification for a particular colorant holds whether the colorant is obtained from natural sources or is synthetically produced, as in the case of natural and synthetic -carotene. 

Metals that depend on a relatively thick protective coating of corrosion product for corrosion resistance are frequently subject to erosion-corrosion. This is due to the poor adherence of these coatings relative to the thin films formed by the classical passive metals, such as stainless steel and titanium. Both stainless steel and titanium are relatively immune to erosion-corrosion in most cooling water environments. 

This example of aluminium illustrates the importance of the protective him, and hlms that are hard, dense and adherent will provide better protection than those that are loosely adherent or that are brittle and therefore crack and spall when the metal is subjected to stress. The ability of the metal to reform a protective him is highly important and metals like titanium and tantalum that are readily passivated are more resistant to erosion-corrosion than copper, brass, lead and some of the stainless steels. There is some evidence that the hardness of a metal is a signihcant factor in resistance to erosion-corrosion, but since alloying to increase hardness will also affect the chemical properties of the alloy it is difficult to separate these two factors. Thus althou copper is highly susceptible to impingement attack its resistance increases with increase in zinc content, with a corresponding increase in hardness. However, the increase in resistance to attack is due to the formation of a more protective him rather than to an increase in hardness. 

Other media in which titanium is subject to pyrophoricity are anhydrous liquid or gaseous chlorine , liquid bromine, hot gaseous fluorine, or oxygen-enriched atmospheres at moderately low pressures. 

Stress-corrosion cracking occurs in titanium alloys in a number of environments, although the number of failures that have occurred under service conditions is very small. Because of the widespread use of titanium alloys in aeroplanes and space vehicles and their increasing use in marine applications it is important that the possibilities of service failures should be removed. As a result a considerable and increasing amount of work has been done on this subject over the last decade as indicated in a recent extensive survey. ... 

The superimposition of a.c. ripple on the d.c. output from a transformer rectifier can under certain circumstances lead to increased platinum consumption rates and has been the subject of considerable researchIndeed, when platinised titanium anodes were first used it was recommended that the a.c. component was limited to 5% of the d.c. voltage . 

Metals which are subject to oxidation or attack by nitrogen can be sprayed in a closed system so that air is exluded. The heat necessary to melt the wire is produced by current generated in the wire itself by high-frequency currents flowing in small water-cooled coils. By this means, titanium, niobium and even uranium, can be sprayed without gaseous contamination. 

For further conversions via the titanium derivative see Section D.l. 3.3.3.8.2.3. The complex of the trimethylsilyl derivative was subjected to an X-ray structure analysis6. 

Nanoparticles of the semicondnctor titanium dioxide have also been spread as mono-layers [164]. Nanoparticles of TiOi were formed by the arrested hydrolysis of titanium iso-propoxide. A very small amount of water was mixed with a chloroform/isopropanol solution of titanium isopropoxide with the surfactant hexadecyltrimethylammonium bromide (CTAB) and a catalyst. The particles produced were 1.8-2.2 nm in diameter. The stabilized particles were spread as monolayers. Successive cycles of II-A isotherms exhibited smaller areas for the initial pressnre rise, attributed to dissolution of excess surfactant into the subphase. And BAM observation showed the solid state of the films at 50 mN m was featureless and bright collapse then appeared as a series of stripes across the image. The area per particle determined from the isotherms decreased when sols were subjected to a heat treatment prior to spreading. This effect was believed to arise from a modification to the particle surface that made surfactant adsorption less favorable. 

All commercial materials are based on calcium hydroxide and liquid alkyl salicylates (Prosser, Grolfman Wilson, 1982) and are supplied as a two-paste pack. Zinc oxide is sometimes added to the calcium hydroxide, as are neutral fillers. A paste is formed from this powder by the addition of a plasticizer examples include A-ethyl toluenesulphonamide (o- orp-) and paraffin oil, with sometimes minor additions of polypropylene glycol. The other paste is based on an alkyl salicylate as the active constituent containing an inorganic filler such as titanium dioxide, calcium sulphate, calcium tungstate or barium sulphate. Alkyl salicylates used include methyl salicylate, isobutyl salicylate, and 1-methyl trimethylene disalicylate. An example of one commercial material, Dycal, is given in Table 9.7, but its composition has been subjected to change over the years. 

Common pollutants in a titanium dioxide plant include heavy metals, titanium dioxide, sulfur trioxide, sulfur dioxide, sodium sulfate, sulfuric acid, and unreacted iron. Most of the metals are removed by alkaline precipitation as metallic hydroxides, carbonates, and sulfides. The resulting solution is subjected to flotation, settling, filtration, and centrifugation to treat the wastewater to acceptable standards. In the sulfate process, the wastewater is sent to the treatment pond, where most of the heavy metals are precipitated. The precipitate is washed and filtered to produce pure gypsum crystals. All other streams of wastewater are treated in similar ponds with calcium sulfate before being neutralized with calcium carbonate in a reactor. The effluent from the reactor is sent to clarifiers and the solid in the underflow is filtered and concentrated. The clarifier overflow is mixed with other process wastewaters and is then neutralized before discharge. 

---