Thin crosslinking

The reactions produced a membrane having three distinct zones of increasing porosity 1) the mlcroporous polysulfone support film, 2) a thin, crosslinked polyethylenlmine zone of Intermediate porosity and moderate salt rejection, and 3) the dense polyamide (or polyurea) surface skin which acted as the high retention barrier. ... 

For many applications, especially technical applications, textiles should be protected against physical or chemical assault, for example abrasion, damage by UV radiation and aggressive chemicals. This can be achieved by thin crosslinked layers of inorganic or mixed inorganic-organic polymers on the fibre surface " These special finishes are carried out with common techniques at moderate processing temperatures that do not exceed 150 °C and result in very thin polymer films on the fibre surface. 

In the case of a polymeric amine such as polyethylenimine or polyepiamine, the solubility of the polymer in the organic phase would be very low. Reaction would take place at the interface to form an extremely thin, crosslinked network. This network would block the transport of further polymeric amine from the aqueous phase into the organic phase. Continued buildup of the membrane material on the organic side becomes impossible. Thereafter, the growth in thickness of the barrier layer is controlled by the much slower diffusion of acyl halide or isocyanate into the aqueous phase. As a result, composite membranes made by the NS-100/NS-101 type of approach will naturally tend to have very thin barrier layers-typically 200 to 250 angstroms thick. 

According to these studies the only common prc rty produced by these widely-differing treatments, all of which give high joint strengths, is a thin, crosslinked or gel surface layer. 

In an attempt to determine the applicability of JKR and DMT theories, Lee [91] measured the no-load contact radius of crosslinked silicone rubber spheres in contact with a glass slide as a function of their radii of curvature (R) and elastic moduli (K). In these experiments, Lee found that a thin layer of silicone gel transferred onto the glass slide. From a plot of versus R, using Eq. 13 of the JKR theory, Lee determined that the work of adhesion was about 70 7 mJ/m". a value in clo.se agreement with that determined by Johnson and coworkers 6 using Eqs. 11 and 16. 

Of all the techniques, it is those of Group 1 that are likely to give the most realistic data, simply because they measure transport of charged species only. They are not the easiest experimental techniques to perform on polymeric systems and this probably explains why so few studies have been undertaken. The experimental difficulties associated with the Tubandt-Hittorf method are in maintaining nonadherent thin-film compartments. One way is to use crosslinked films [79], while an alternative has been to use a redesigned Hittorf cell [80]. Although very succesful experimentally, the latter has analytical problems. Likewise, emf measurements can be performed with relative ease [81, 82] it is the necessary determination of activity coefficients that is difficult. 

Very thin films may be also obtained through adsorption of a thin layer from solution [11,71,74] or chemical grafting [98] which is achieved by a polymerization reaction at the surface. A polymer film may also be deposited on the surface by plasma polymerization [99]. It is then, however, usually crosslinked and chemically not well-defined. 

Immobilization of (3-D-glucosidase from almonds on photo-crosslinkable resin prepolymer (ENTP-4000) was carried out by the following procedure. One gram of ENTP-4000 was mixed with 10 mg of a photosensitizer, benzoin ethyl ether, and 110 mg of (3-D-glucosidase from almonds (3.4 units mg ). The mixture was layered on a sheet of transparent polyester film (thickness, ca. 0.5 mm). The layer was covered with transparent thin film and then illuminated with chemical lamps (wavelength range 300 00 nm) for 3 min. The gel film thus obtained was cut into small pieces (0.5 x 5 x 5 mm) and used for bioconversion reaction. 

The predominant RO membranes used in water applications include cellulose polymers, thin film oomposites (TFCs) consisting of aromatic polyamides, and crosslinked polyetherurea. Cellulosic membranes are formed by immersion casting of 30 to 40 percent polymer lacquers on a web immersed in water. These lacquers include cellulose acetate, triacetate, and acetate-butyrate. TFCs are formed by interfacial polymerization that involves coating a microporous membrane substrate with an aqueous prepolymer solution and immersing in a water-immiscible solvent containing a reactant [Petersen, J. Memhr. Sol., 83, 81 (1993)]. The Dow FilmTec FT-30 membrane developed by Cadotte uses 1-3 diaminobenzene prepolymer crosslinked with 1-3 and 1-4 benzenedicarboxylic acid chlorides. These membranes have NaCl retention and water permeability claims. 

When this resin was exposed as a thin film to the UV radiation of a medium pressure mercury lamp (80 W aiH), the crosslinking polymerization was found to develop extensively within a fraction of a second (18). The kinetics of this ultra-fast reaction can be followed quantitatively by monitoring the decrease of the IR absorption at 810 an-1 of the acrylic double bond (CHCH twisting). Figure 8 shows a typical kinetic curve obtained for a 20 pm thick film coated onto a NaCl disk and exposed in the presence of air to the UV radiation at a fluence rate of 1.5 x 10 6 einstein s-1 cm 2. 

Tao, T., Lamkin, M., and Schemer, C. (1984) Studies on the proximity relationships between thin filament proteins using benzophenone-4-maleimide as a site-specific photoreactive crosslinker. Biophys. J. 45,261. 

The crosslinkers examined in this study were aminoplast resins 1-4 selected from melamine-formaldehyde, urea-formaldehyde, benzoguanamine-formaldehyde, and glycoluril-formaldehyde resins, all of which undergo the crosslinking sequence shown in Scheme 1. The response of these crosslinkers to acid catalysis in thin films is compared on a relative basis to the well studied methylated melamine, 1 19-11). 

---