Testing water-soluble polymers

There have been numerous communications on the subject of biodegradation test methods, including aerobic compost (30), anaerobic bioreactor (31), general methodology and future directions (32—34), and a fine review article (24). ASTM (22) and MITI (35) have also set forth standard testing protocols for plastics, as shown in Table 2, whereas OECD test methods (29) are more suited to water-soluble polymers. 

When suitably viscosified, TKPP solutions become superior low solids drilling fluids. Many water-soluble polymers were tested to identify satisfactory viscosifiers. Most commercially available polymers were found to be insoluble in TKPP solutions at densities above 11 ppg. Only xanthan gum... 

Amphoteric water-soluble polymers, 20 475 Ampicillin, registered for use in aquaculture in Japan, 3 221t AmpliChip CYP450 Test, 16 392 Amplifiers, optical, 11 145-146 Amrinone, 5 186... 

Within this group, the linear polymers have been most intensively studied and researched. The main area of interest lies in water-soluble polymers. However, there have also been many studies into organic solutions, although there exist problems with odor and toxicity in the case of analytical studies. Among the water-soluble additives, tests were made especially on polyethyleneoxide (PEO), polyacrylamide and the coacrylates (PAAm, PAAm/AAcNa), polyacrylic add (PAA), guar gum (GG), carboxymethylcellulose (CMC) and sodium salts, as well as hydroxyethylcellulose (HEC). From these tests, PEO proved to be the most effective flow improver, followed closely by PAAm, which is somewhat more stable than PEO in turbulent flow. 

The Kirkwood-Buff theory of solutions for ternary mixtures was used to analyze the gas solubility in a mixed binary solvent composed of a high molecular weight and a low molecular weight cosolvent, such as the aqueous solutions of water soluble polymers. A rigorous expression for the composition derivatives of the gas activity coefficient in ternary solution was used to derive the composition dependence of the Henry constant under isobaric and isothermal conditions. The obtained expressions as well as the well-known Kri-chevsky equation were tested for the solubilities of Ar, CH4, C2H6 and C3H8 in the aqueous solutions of PPG-... 

PEG-supported cinchona ammonium salts 54 were applied to the asymmetric alkylation of tert-butyl benzophenone Schiff base derivatives 52 [34]. The use of a water-soluble polymer support allowed the reaction to be conducted in a 1M KOH aqueous solution to give the a-amino acid derivatives 53 in high chemical yields (up to 98%). Ten different types of electrophile have been tested for the reaction, with the best enantioselectivity being obtained with o-chlorobenzylchloride (97% ee) (Scheme 3.15). 

Selective separation and concentration of both cations and anions using water-soluble polymer solutions LM as carriers and hoUow-fiber units (artificial kidneys) as membrane barrier were tested. The authors termed the process as affinity dialysis [74]. Hollow fiber units of Spectrum Medical Industries, Inc. with fibers of 5000 molecular weight cutoff and 150 cm surface area from Spectrapor were used in the experiments. 

A number of hydroxylated water soluble polymers were examined as coreactants with polymer 52 in the absence of calcium alginate, and were judged on the basis of the rate of gel formation and the physical properties of the gel These polymers included sodium alginate, polyvinyl alcohol, and copolymers of HEMA with MAA. Of the polymers tested, best results were obtained with polymer 10a, a copolymer of HEMA with a mole fraction of about 10% MAA, which rapidly produced an elastic gel on exposure to polymer 52 in solution. Simple condensation of the carboxyls in polymer 10a with the epoxide functionality was ruled out as a competing reaction due to the measurable but slow reaction between polymer 52 and poly methacrylic acid. It is, therefore, likely... 

Phthalocyanines with M = Si(OH)2 or Ge(OH)2 were eovalently incorporated into polyesters during the polycondensation of terephthalic acid dimethylester and ethylene glycol [182]. With only lO" molar amounts of dye, the polyesters are intensely blue-colored. Good solubility can be achieved in water by axial substitution at the central metal or with hydrophilic polymers. Phthalocyanines with the tetravalent M = SiCb were reacted with the sodium salt of methoxypoly(oxyethylene) (M = 5000 Da) to give the blue-colored polymer 68 which is soluble in water and some organic solvents [183]. The reaction of phthalocyanines with the trivalent M = AlCl with poly-(oxyethylene) or poly(vinylalcohol) also led to water-soluble polymers having covalent bonds of the polymers at the Al(III) [184]. These water-soluble materials have been tested in the photodynamic therapy of cancer. 

Zimmermann et al. [134] have used cellulose fibrils obtained from sulphite wood pulp to reinforce water soluble polymers such as polyvinyl alcohol (PVA) and hydroxypropyl cellulose (HPC). The mechanical properties of these nanocomposites were measured by tensile tests showing that the addition of fibrils increase the modulus of elasticity (E) up to three times and the tensile strength up to five times compared to the raw polymer. Zimmermann et al. [135] have determined the E values and the hardness of cellulose/HPC nanocomposites using nanoindentation technique. The results showed that the E values measured by nanoindentation were from two to three times higher than the E values measured by means of tensile tests. Stauss et al. [136] have explained that differences between tensile test and indentation results are due to the fact that they do not test the same material volumes and regions. The large volume used in tensile test includes defects such as pores, cracks and impurities. 

---