Test methods sample

Use of DPS, WURST and HS pulses (for 41 testing methods). Sample with fast spin relaxation. 

Test Method Sample Amount Cost Number of Transcripts Advantages Disadvantages Comment... 

Test method Sample size, in Position of sample Ignition source, flame, in Time and limit of exposure, s Value reported, in/min Usual material application... 

Section 12(d) of the National Technology Transfer and Advancement Act of 1995 (NTTAA), Public Law No. 104-113, 12(d) (15 U.S.C. 272 note), directs EPA to use voluntary consensus standards in its regulatory activities unless to do so would be inconsistent with applicable law or otherwise impractical. Voluntary consensus standards are technical standards (e.g., materials specifications, test methods, sampling procedures, and business practices) that are developed or adopted by voluntary consensus standards bodies. 

The NCMS project developed a large data set of the mechanical properties of lead-free solder alloys. For three Pb-free solder alloys and eutectic Sn Pb, these include creep data, constitutive equations, and microstructural data, as well as detailed descriptions of test methods, sample geometries, and material data for the components and boards used in the experimental testing, as listed in Table 15. Partial datasets for 75 additional solder alloys were generated and are included in the NCMS CDROM [2]. 

Penetrability is the depth, expressed in tenths of a millimeter, a standard steel needle penetrates into a bitumen sample at 25°C. The needle carries a weight of 100 g and the test is applied for five seconds. The corresponding test method is relatively difficult to carry out and is defined in France by the standard NF T 66-004, and in the USA by the method ASTM D 583. Penetration is related to the viscosity. 

Measuring surface crack depth is performed by calibration samples made of the same material like the object being tested. Calibration samples are the plates having narrow grooves like slits of various depth 0.2 mm, 0.5 mm, 1.0 mm, 2.0 mm, 3.0 mm, 4.0 mm, 5.0 mm and made by electric erosion method. The samples have dimensions 50 mm X 150 mm x 6 mm and 25 mmx 150 mm x 6 mm and are made of magnetic... 

Fire test methods attempt to provide correct information on the fire contribution of a product by exposing a small sample to conditions expected in a fire scenario. Methods can be viewed in two ways the first entails the strategy of the fire test, ignition resistance or low flammabiUty once ignited the second addresses the test specimen, a sample representative of the product or a sample of a material that might be used in the product. Fire science has progressed markedly since the older test methods were developed and it is known that the basis for many of these tests is doubthil. Results from older tests must be used with great care. 

Another ASTM test method. Potential Gum (D873), combines the existent gum and the oxidation stabihty tests to measure potential gum. A sample of gasoline is subjected to the oxidation stabihty test for 960 min, filtered to remove particulates, and then subjected to an existent gum test. The potential gum is expressed as the total (unwashed) gum in this test. 

One advantage of the impedance tube test methods is the small (usually <10 cm (4 ia.) dia) size of the test samples. For these tests sound impinges on the test sample only at normal iacidence to the surface, and the sound-absorption coefficients derived ia this manner are vaUd only at this angle. 

L bor toiyMethods. The laboratory test method for determining the sound-transmission loss performance of constmctions is defined in ASTM E90-90 (11). The sample is installed in an opening between two highly reverberant rooms that are acoustically well isolated from each other. 

The test methods used by industry to determine if a sample of maleic anhydride is within specifications (165) ate ASTM methods D2930, D1493, and D3366. These methods describe procedures for the determination of maleic acid content, the crystallization point, and the color properties of the maleic anhydride sample, respectively. By quantitative deterrnination of these properties, a calculation of the overall purity of the maleic anhydride sample can be made. 

The free maleic acid content in maleic anhydride is determined by direct potentiometric titration (166). The procedure involves the use of a tertiary amine, A/-ethylpipetidine [766-09-6J, as a titrant. A tertiary amine is chosen as a titrant since it is nonreactive with anhydrides (166,167). The titration is conducted in an anhydrous solvent system. Only one of the carboxyhc acid groups is titrated by this procedure. The second hydrogen s dissociation constant is too weak to titrate (166). This test method is not only used to determine the latent acid content in refined maleic acid, but also as a measure of the sample exposure to moisture during shipping. 

Analytical and Test Methods. Measurement of the sohdification point using a highly sensitive thermometer and of APHA color by comparison of molten samples to APHA standards is straightforward. Specific impurities are measured by gas chromatography. A nonaqueous titration is used to determine phthahc acid content. 

Analytical and Test Methods. The acid number of terephthahc acid discussed above is a titration of a sample dissolved in pyridine, using a sodium or potassium hydroxide titrant. However, specifications on certain impurities are so strict that this test caimot, as a practical matter, be failed. Its use has been discontinued by some manufacturers. 

Analytical and Test Methods. Ash in isophthahc acid refers to the residue left after combustion of the sample. Ash consists of oxides of trace metals that are deterrnined individually by atomic absorption or inductively coupled plasma. A Kad Fischer titration is specific for the water content. 

Test Methods. In addition to that provided by proper sampling and rephcation of analysis, a test method also has a significant impact on the accuracy and precision of the results. Preferred methods are those which are accepted in the chemical industry such as those from the American Society of Testing Materials (ASTM), Association of Official Analytical Chemists (AO AC), or from compendia such as the United States Pharmacopoeia (USP) or the Pood Chemical Codex (FCC) (36). The use of such methods eliminates the need for method vahdation. 

ASTM D5147, Standard Test Methods for Sampling and Testing Modified Bitumen Sheet Materials, ASTM, Philadelphia, Pa. 

U. S. EPA Regulations on Standards ofPeformanceforNeir Stationay Sources, 40 CER 60, Appendix A, Reference Methods, Washington, D.C., 1993. ASTM D3685-92, Standard Test Methodfor Sampling and Determination of Particulate Matter in Stack Gases, American Society for Testing Materials, Philadelphia, Pa., 1992. 

Water resistance test methods include AATCC 127 (hydrostatic pressure test), AATCC 42 (impact penetration test), and AATCC 35 (rain test). In the hydrostatic pressure test, a sample is subjected to a column of increasing water pressure until leakage occurs. The impact penetration test requires water to be sprayed on the taut surface of a fabric sample from a height of two feet. The fabric is backed by a blotter of predeterrnined weight, which is reweighed after water penetration. The rain test is similar in principle to the impact penetration test. 

Rotating Beam Fatigue Test for Steel Cords. The purpose of this test method is to evaluate steel cord for pure bending fatigue (121). The test sample consists of a 3-mm diameter mbber embedded with steel cord. Different bending stress levels are appHed and the time to failure is recorded. The test stops at 1.44 million cycles. The fatigue limit is calculated from S—N (stress—number of cycles) curve. 

---