Surface-active substance

Membranes and Osmosis. Membranes based on PEI can be used for the dehydration of organic solvents such as 2-propanol, methyl ethyl ketone, and toluene (451), and for concentrating seawater (452—454). On exposure to ultrasound waves, aqueous PEI salt solutions and brominated poly(2,6-dimethylphenylene oxide) form stable emulsions from which it is possible to cast membranes in which submicrometer capsules of the salt solution ate embedded (455). The rate of release of the salt solution can be altered by surface—active substances. In membranes, PEI can act as a proton source in the generation of a photocurrent (456). The formation of a PEI coating on ion-exchange membranes modifies the transport properties and results in permanent selectivity of the membrane (457). The electrochemical testing of salts (458) is another possible appHcation of PEI. 

Surface-active substances (SAS) are the most widespread contaminants of sewage and natural waters. They translate in small dispertion condition liquid and firm polluting substances - chlororganic, mineral oils, pesticides. Therefore, the SAS contents determination in water solutions is now one of actual tasks of analytical chemistry. 

The potentiometry sensor (ion-selective electrode) controls application for determination of polymeric surface-active substances now gets the increasing value. Potentiometry sensor controls are actively used due to simple instmment registration, a wide range of determined concentrations, and opportunity of continuous substances contents definition. That less, the ionometry application for the cation polymeric SAS analysis in a solution is limited by complexity of polycation charge determination and ion-exchanger synthesis. 

In presence of polyamines the maximum of light absorption of indicated triphenylmethane dyes displaces on 10-30 nm, for azo dyes the shift of the band reaches 50-80 nm. The greatest difference of light absorption of associates and reagents is watched for BKM at pH 5,05, for BPR at pH 4,20, for CPR in an interval pH 5,05-5,45. At these pH dyes are anions, it promotes interaction with a cationic surface-active substance. The ratios between polymer and BKM, BPR, CPR are established by spectroscopy method, its equal 1 20, 1 20 and 1 30 accordingly. 

Last years the polymeric surface - active substances began to use as modifiers of organic reagent properties. In our work the behavior of synthetic polymers (polysulphonilpiperidinilmethylenhydroxide (PSPMH), polyvinylpyrrolidone (PVP), polyamines - polyguanidine and metacide) and natural polymers (starch, gelatin) for various molecular masses are investigated. 

The perspective of using consecutive reactions is grounded on the example of the analysis of isomeric mono-nitrophenols and anion surface-active substances. The variants of systematic analysis of mixtures of tri-, di- and mono-nitrophenols, anion surface-active substances, based on the combination of measurements of consecutively received extracts at different pH values are discussed. 

The polymeric latex obtained in a hydrophobic organic solvent is poorly dispersed in water because of the presence of an emulsifier with a low HLB value. For this reason, a wetting agent is added to water or emulsion prior to the dissolution. The wetting agent (a surface active substance with a high HLB value) facilitates the inversion of latex phases to produce a direct type emulsion. Usually, it belongs to oxyethylated alkylphenols, fatty alcohols, or fatty acids. 

R. C. Schulz, P. R. Pujado, and B. V. Vora, presented at 2nd World Conference on Surface Active Substances, Montreux, Switzerland, 1986. 

L. Cavalli et al., 3rd CESIO World Congress on Surface Active Substances, London, 1992. 

R. Wickbold, Proc. lVth Int. Congress on Surface Active Substances, Vol. 3, Brussels, 1964, pp. 903-912. 

Adsorption of various organic compounds (e.g., cyclohexanol, adamantanol-1, and camphor) has been studied at a renewed Sn + Pb alloy/electrolyte interface.820-824 The time variation of the surface composition depends on the solution composition, the nature and concentration of the surface-active substance, and on E. The " of cyclohexanol for just-renewed Sn + Pb alloys shifts toward more negative E with time, i.e., as the amount of Pb at the Sn + Pb alloy surface increases. 

Carotenoid/ curcumin/porphyrin Water dispersion without using compositions surface-active substance... 

On the basis of this definition, one can determine, for instance, the activity of electrolytic solutions in terms of the real hydrogen ion activity. Rybkin et al. found that the Ax effect may be stabilized by adding surface-active substances in small quantities to the solution. Ac-... 

Adsorption of surface-active substances is attended by changes in EDL structure and in the value of the / -potential. Hence, the effects described in Section 14.2 will arise in addition. When surface-active cations [NR] are added to an acidic solution, the / -potential of the mercury electrode will move in the positive direction and cathodic hydrogen evolution at the mercury, according to Eq. (14.16), will slow down (Fig. 14.6, curve 2). When I ions are added, the reaction rate, to the contrary, will increase (curve 3), owing to the negative shift of / -potential. These effects disappear at potentiafs where the ions above become desorbed (at vafues of pofarization of less than 0.6 V in the case of [NR]4 and at values of polarization of over 0.9 V in the case of I ). 

In the process of passivation, metals usually are found only in one of the two extreme states, active or passive. The transition between these states occurs suddenly and discontinuously. The intermediate state in region BC can only be realized with special experimental precautions. It is in this sense that passivation differs from the inhibition of electrochemical reactions observed during adsorption of a number of surface-active substances, where the degree of inhibition varies smoothly with the concentration of added material. 

Electrokinetic processes are widely used in different fields of science and technology. We had already mentioned the use of electrokinetic processes for research into the electric properties of surface layers of insulating materials. Such measurements are used, in particular, when studying the surface properties of polymeric materials, their behavior in different media, and their interactions with other materials (e.g., with adsorbing surface-active substances). The results of this research are used in textile, cellulose and paper, and other industries. 

The appreciation of the importance of adsorption phenomena at liquid interfaces is probably as old as human history, since it is easily recognized in many facets of everyday life. It is not surprising that liquid interfaces have been a favorite subject of scientific interest since as early as the eighteenth century [3,4], From an experimental point of view, one obvious virtue of the liquid interfaces for studying adsorption phenomena is that we can use surface tension or interfacial tension for thermodynamic analysis of the surface properties. The interfacial tension is related to the adsorbed amount of surface active substances through the Gibbs adsorption equation. 

Thus, the HLB of an ionic surface-active substance is balanced at the standard ion-transfer potential. This is simply a reinterpretation of the definition of Aq P, but is a very important relation, which is valid no matter what the actual form of the adsorption... 

In the electrode-solution interphase, the adsorption of these substances is also affected by the influence of the electric field in the double layer on their dipoles. Substances that collect in the interphase as a result of forces other than electrostatic are termed surface-active substances or surfactants. 

Electroneutral substances that are less polar than the solvent and also those that exhibit a tendency to interact chemically with the electrode surface, e.g. substances containing sulphur (thiourea, etc.), are adsorbed on the electrode. During adsorption, solvent molecules in the compact layer are replaced by molecules of the adsorbed substance, called surface-active substance (surfactant).t The effect of adsorption on the individual electrocapillary terms can best be expressed in terms of the difference of these quantities for the original (base) electrolyte and for the same electrolyte in the presence of surfactants. Figure 4.7 schematically depicts this dependence for the interfacial tension, surface electrode charge and differential capacity and also the dependence of the surface excess on the potential. It can be seen that, at sufficiently positive or negative potentials, the surfactant is completely desorbed from the electrode. The strong electric field leads to replacement of the less polar particles of the surface-active substance by polar solvent molecules. The desorption potentials are characterized by sharp peaks on the differential capacity curves. 

The basic quantity in the study of adsorption is the surface excess of the surface-active substance. In the formation of a monomolecular film of the... 

The fact that the electrocapillary quantities are measured relative to their value in the base electrolyte can also be expressed in the formulation of the Gibbs-Lippmann equation. If quantities referred to the base electrolyte are primed and quantities referred to the studied surface-active substance are denoted by the subscript 1, then... 

Equation (4.3.37) can be used to determine the function = T1(c1), which is the adsorption isotherm for the given surface-active substance. Substitution for c1 in the Gibbs adsorption isotherm and integration of the differential equation obtained yields the equation of state for a monomole-cular film = T jt). 

It is very simple to determine the value of = T/Tm for a strongly adsorbed substance in electrolysis with a dropping mercury electrode. If a much smaller amount of substance is sufficient for complete electrode coverage than available in the test solution, then the surface concentration of the surface-active substance T is determined by its diffusion to the electrode. 

Whiskers are sometimes formed in solutions with high concentrations of surface-active substances. These are long single crystals, growing in only one direction, while growth in the remaining directions is retarded by adsorption of surface-active substances. Whiskers are characterized by quite... 

---