Sulfur compounds, protection

Natural gas contains both organic and inorganic sulfur compounds that must be removed to protect both the reforming and downstream methanol synthesis catalysts. Hydrodesulfurization across a cobalt or nickel molybdenum—zinc oxide fixed-bed sequence is the basis for an effective purification system. For high levels of sulfur, bulk removal in a Hquid absorption—stripping system followed by fixed-bed residual clean-up is more practical (see Sulfur REMOVAL AND RECOVERY). Chlorides and mercury may also be found in natural gas, particularly from offshore reservoirs. These poisons can be removed by activated alumina or carbon beds. 

Contaminants in fuels, especially alkali-metal ions, vanadium, and sulfur compounds, tend to react in the combustion zone to form molten fluxes which dissolve the protective oxide film on stainless steels, allowing oxidation to proceed at a rapid rate. This problem is becoming more common as the high cost and short supply of natural gas and distillate fuel oils force increased usage of residual fuel oils and coal. 

The horizontal surfaces should be coated because there is residual water in the ballast and there are water-oil mixtures in the crude oil tanks when ships travel empty and these can cause severe corrosion attack. In the lower part of the tank, up to about 1.5 m from the base, a combination of coating and cathodic protection with special anodes is chosen. Basically the anodes could take over the exclusive protection in this area, but with empty ballast tanks containing residual water or empty crude oil tanks with aggressive oil-water mixtures containing sulfur compounds, they do not prevent corrosion. 

In the manufacture of varnish, heat is necessary for formulation and purificahon. The same may be true of operations preparing paints, shellac, inks, and other protective or decorative coahngs. The compounds emitted to the atmosphere are gases, some with extremely low odor thresholds. Acrolein, with an odor threshold of about 4000 /xg/m, and reduced sulfur compounds, with odor thresholds of 2 are bofh possible emissions... 

It is well established that sulfur compounds even in low parts per million concentrations in fuel gas are detrimental to MCFCs. The principal sulfur compound that has an adverse effect on cell performance is H2S. A nickel anode at anodic potentials reacts with H2S to form nickel sulfide. Chemisorption on Ni surfaces occurs, which can block active electrochemical sites. The tolerance of MCFCs to sulfur compounds is strongly dependent on temperature, pressure, gas composition, cell components, and system operation (i.e., recycle, venting, and gas cleanup). Nickel anode at anodic potentials reacts with H2S to form nickel sulfide. Moreover, oxidation of H2S in a combustion reaction, when recycling system is used, causes subsequent reaction with carbonate ions in the electrolyte [1]. Some researchers have tried to overcome this problem with additional device such as sulfur removal reactor. If the anode itself has a high tolerance to sulfur, the additional device is not required, hence, cutting the capital cost for MCFC plant. To enhance the anode performance on sulfur tolerance, ceria coating on anode is proposed. The main reason is that ceria can react with H2S [2,3] to protect Ni anode. 

The traditional catalyst used for esterification of acids to methyl esters is sulfuric acid. Homogeneous sulfuric acid catalysis has many downsides. When using sulfuric acid, much capital expense is required for Hastalloy and/or other specialty metals of construction. Homogeneous catalysis results in the contamination of the product by sulfur containing species. Therefore, neutralization and removal of acid is required to meet biodiesel specifications and to protect the downstream transesterification reactor. Inevitably, when using sulfuric acid, organic sulfur compounds will be produced. These products will cause the resultant biodiesel to fail specification tests. 

Stability Unstable in air. Protect from water or moisture. Store away horn heat or ignition sources and sulfur compounds. Reacts with sulfur and sulfur compounds, producing highly toxic VX or VX-like compounds. It completely dissolves polymethylmethacrylate. It is incompatible with calcium hypochlorite (HTH), many chlorinated hydrocarbons, selenium, selenium compounds, moisture, oxidants, and carbon tetrachloride. 

Figure 14.2 shows that the production of 99% pure hydrogen requires many catalytic processes. The desulfurization section is used to reduce the sulfur content of the natural gas to 0.01 ppm to protect the SMR and WGS catalysts downstream. A supported cobalt-molybdenum catalyst (CoMoS) converts the sulfur compounds into H2S, which is removed by a ZnO catalyst [5]. 

Both the natural clay and the synthetic types of catalyst undergo normal aging. Abnormal aging, due to sulfur compounds, has been found only with natural clay catalyst the synthetic types are stable under similar conditions. Natural clay catalysts can be protected against abnormal aging from sulfur compounds by hydrating with steam after regeneration. Certain types of iron-free clays and bentonitic clays treated to remove iron do not show sulfur deactivation. 

The petroleum industry has taken the position that oil and gas production can and will be compatible with a high level of public health and environmental protection. The treating facilities at Jay are designed to achieve this goal, particularly regarding the emission of sulfur compounds into the atmosphere. 

As in the case of poly(U), which has been studied as a model system in some detail (Chap. 11.2), there is a relationship of the rate of protection of DNA by thiols and disulfides and the charge of the sulfur compound due to ion condensation (for evidence of this phenomenon, see Smoluk et al. 1988b). As has been measured by following the protection of DNA irradiated in aqueous solution against base release (Zheng et al. 1988), G(base release) follows the equation G0/Gp = 1 + 3[RSH]. The data, compiled in Table 12.16, have been interpreted in terms of electrostatic interaction of thiols of the thiols/disulfides with DNA leading to higher concentrations of cations with respect to neutral thiols/disulfides... 

Table 5.15. Protective tribofilm formation from degradation of molybdenum dithiocarbamate (MoDTC), molybdenum dithiophosphate (MoDDP) and molybdenum amine-ester complex (MoAC) directly and in combination with ZDDPs or sulfur compounds...

Re has recently come to the forefront in liquid phase oxidation catalysis, mainly as a result of the discovery of the catalytic properties of the alkyl compound CH3Re03 [methyltrioxorhenium (MTO)]. MTO forms mono-and diperoxo adducts with H2O2 these species are capable of transferring an oxygen atom to almost any nucleophile, including olefins, allylic alcohols, sulfur compounds, amides, and halide ions (9). Moreover, MTO catalysis can be accelerated by coordination of N ligands such as pyridine (379-381). An additional effect of such bases is that they buffer the strong Lewis acidity of MTO in aqueous solutions and therefore protect epoxides, for example. 

---