Sulfide utilization

Sinha S. N. and Baneijee R. D. (1997) Ecological role of thiosulfate and sulfide utilizing purple nonsulfur bacteria of a riverine ecosystem. FEMSMicrobiol. Ecol. 24(3), 211-220. 

The basic flow sheet for the flotation-concentration of nonsulfide minerals is essentially the same as that for treating sulfides but the family of reagents used is different. The reagents utilized for nonsulfide mineral concentrations by flotation are usually fatty acids or their salts (RCOOH, RCOOM), sulfonates (RSO M), sulfates (RSO M), where M is usually Na or K, and R represents a linear, branched, or cycHc hydrocarbon chain and amines [R2N(R)3]A where R and R are hydrocarbon chains and A is an anion such as Cl or Br . Collectors for most nonsulfides can be selected on the basis of their isoelectric points. Thus at pH > pH p cationic surfactants are suitable collectors whereas at lower pH values anion-type collectors are selected as illustrated in Figure 10 (28). Figure 13 shows an iron ore flotation flow sheet as a representative of high volume oxide flotation practice. 

Molecular Sieve Treatment. Molecular sieve treaters can be designed to remove H2S, organic sulfur compounds (including carbonyl sulfide), and water in one step. SoHd-bed units are utilized and regeneration occurs in the same manner as simple, soHd-bed dehydrators. 

Solid-Bed Caustic Treatment. SoHd-bed caustic units utilizing methanol [67-56-1] injection into the LPG feed stream can be used for carbonyl sulfide removal. The methanol—caustic solution must be drained periodically from the beds and discarded. When the soHd bed is exhausted, the spent caustic must be discarded and replaced. The LPG from the treater has a low enough water content to meet the propane specification. 

The neat resin preparation for PPS is quite compHcated, despite the fact that the overall polymerization reaction appears to be simple. Several commercial PPS polymerization processes that feature some steps in common have been described (1,2). At least three different mechanisms have been pubUshed in an attempt to describe the basic reaction of a sodium sulfide equivalent and -dichlorobenzene these are S Ar (13,16,19), radical cation (20,21), and Buimett s (22) Sj l radical anion (23—25) mechanisms. The benzyne mechanism was ruled out (16) based on the observation that the para-substitution pattern of the monomer, -dichlorobenzene, is retained in the repeating unit of the polymer. Demonstration that the step-growth polymerization of sodium sulfide and /)-dichlorohenzene proceeds via the S Ar mechanism is fairly recent (1991) (26). Eurther complexity in the polymerization is the incorporation of comonomers that alter the polymer stmcture, thereby modifying the properties of the polymer. Additionally, post-polymerization treatments can be utilized, which modify the properties of the polymer. Preparation of the neat resin is an area of significant latitude and extreme importance for the end user. 

An important aspect of this is the splitting of the polymer chain with thiol (eq. 5) or mercaptide ion (thiol + base catalyst). In fact, sodium sulfide or organic monothiols, eg, mercaptoethanol or decyhnercaptan, are utilized to lower the molecular weight of polysulftdes or to limit the extent of curing reactions. 

Polymers, metals, ceramics, and glasses may be utilized as biomaterials. Polymers (see Ppolymerprocessing), an important class of biomaterials, vary gready in stmcture and properties. The fundamental stmcture may be one of a carbon chain, eg, in polyethylene or Tedon, or one having ester, ether, sulfide, or amide bond linkages. PolysiHcones, having a —Si—O—Si— backbone, may contain no carbon. 

Silver sulfate decomposes above 1085°C into silver, sulfur dioxide, and oxygen. This property is utilized ia the separation of silver from sulfide ores by direct oxidation. Silver sulfate is reduced to silver metal by hydrogen, carbon, carbon monoxide, zinc, and copper. 

Diethanolamine (DEA) has replaced MEA as the most widely used amine solvent. High load DEA technologies, such as that developed by Elf Aquitaine, permit the use of high (up to 40 wt % DEA) concentration solutions. The Elf Aquitaine—DEA process allows lower cinculation rates, and has consequent reductions ia capital and utility expenses. DEA tends to be more resistant to degradation by carbonyl sulfide and carbon disulfide than MEA. DEA is, however, susceptible to degradation by carbon dioxide. 

Free-Radical-Initiated Synthesis. Free-radical-initiated reactions of hydrogen sulfide to alkenes are commonly utilized to prepare primary thiols. These reactions, where uv light is used to initiate the formation of hydrosulfuryl (HS) radicals, are utilized to prepare thousands of metric tons of thiols per year. The same reaction can be performed using a radical initiator, but is not as readily controlled as the uv-initiated reaction. These types of reactions are considered to be anti-Markownikoff addition reactions. 

Coal ash is derived from the mineral content of coal upon combustion or utilization. The minerals are present as discrete particles, cavity fillings, and aggregates of sulfides, sulfates, chlorides, carbonates, hydrates, and/or oxides. The key ash-forming elements and compounds are (4,5) ... 

Sodium sulfide may be conveniently recrystallized from ethanol. Unrecrystallized material may be utilized. However, significantly lower yields will result if the ensuing minor modification is not followed. 

Blowdown systems utilize a series of flash drums and condensers to separate the blowdown into its vapor and liquid components. The liquid is typically composed of mixtures of water and hydrocarbons containing sulfides, ammonia, and other contaminants, which are sent to the wastewater treatment plant. 

It is interesting to note that Kulstad and Malmsten have utilized yet another method for introducing nitrogen into the crown precursors. They utilize sodium azide in DMSO to displace halogen from triethylene glycol dichloride. The bis-azide is then reduced using hydrogen sulfide in ethanol. ... 

At about the same time Pedersen s work was underway, Bradshaw and his coworkers had undertaken the systematic preparation of numerous mono- and polysulfur macrocycles The syntheses were carried out in a fashion similar to that shown in Eq. (6.3). The two principal sources of sulfur in the first paper from this groupwere sodium sulfide and 1,2-ethanedithiol. The latter was utilized in the presence of sodium hydroxide base. Ethanol was generally used as solvent and the reactions were conducted at high dilution. Products were purified either by vacuum distillation or recrystallization as appropriate. The yields were generally in the 5—30% range. 

Another reagent system that has been recently employed in the Paal synthesis of thiophenes is the combination of bis(trialkyltin)- or bis(triaryltin) sulfides with boron trichloride. Known as the Steliou reagent,it has been utilized in the transformation of 1,4-diketone 11 to thiophene 12. Higher yields are obtained in shorter reaction times in contrast to the use of Lawesson s reagent. Additionally, others have noted the relative ease of the work-up procedure using the Steliou conditions, and the fact that the tributyltinchloride byproduct of the reaction is reusable. Similarly, the combination of the bis(trimethylsilyl)sulfide has been used in conjunction with trimethylsilyltriflate for the preparation of thiophenes in an analogous manner. ... 

Depolarization of the cathode by SRB. SRB contain an enzyme called hydrog-enase, which allows the utilization of hydrogen to reduce sulfate to sulfide ... 

Diethanolamine is a favored absorbent due to its lower corrosion rate, smaller amine loss potential, fewer utility requirements, and minimal reclaiming needs. Diethanolamine also reacts reversibly with 75% of carbonyl sulfides (COS), while the mono- reacts irreversibly with 95% of the COS and forms a degradation product that must be disposed of. 

---