Steam propane

Oxygen-Coke-Steam Air-Coke-Steam Oxygen-Coal-Steam Oxygen-Fuel Oil-Steam Propane-Steam... 

Oxygen-coke-steam Air-coke-steam Oxygen-coal-steam Oxygen-fuel oil-steam Propane-steam Methane-oxygen Methane-oxygen-steam Methane-steam... 

Steam dehydrogenation is to increase the equihbrium conversion by decreasing the partial pressure of paraffin, an idea similar to dehydrogenation under vacuum. Using Aspen Plus, the equihbrium conversion under different steam/propane and hydrogen/propane ratio was predicted and the results are shown in Fig. 2.13. 

A two-step process involving conventional nonoxidative dehydrogenation of propane to propylene in the presence of steam, followed by the catalytic ammoxidation to acrylonitrile of the propylene in the effluent stream without separation, is also disclosed (65). 

Olefins are produced primarily by thermal cracking of a hydrocarbon feedstock which takes place at low residence time in the presence of steam in the tubes of a furnace. In the United States, natural gas Hquids derived from natural gas processing, primarily ethane [74-84-0] and propane [74-98-6] have been the dominant feedstock for olefins plants, accounting for about 50 to 70% of ethylene production. Most of the remainder has been based on cracking naphtha or gas oil hydrocarbon streams which are derived from cmde oil. Naphtha is a hydrocarbon fraction boiling between 40 and 170°C, whereas the gas oil fraction bods between about 310 and 490°C. These feedstocks, which have been used primarily by producers with refinery affiliations, account for most of the remainder of olefins production. In addition a substantial amount of propylene and a small amount of ethylene ate recovered from waste gases produced in petroleum refineries. 

Natural gas Hquids represent a significant source of feedstocks for the production of important chemical building blocks that form the basis for many commercial and iadustrial products. Ethyleae (qv) is produced by steam-crackiag the ethane and propane fractions obtained from natural gas, and the butane fraction can be catalyticaHy dehydrogenated to yield 1,3-butadiene, a compound used ia the preparatioa of many polymers (see Butadiene). The / -butane fractioa can also be used as a feedstock ia the manufacture of MTBE. 

Thermal Cracking. / -Butane is used in steam crackers as a part of the mainly ethane—propane feedstream. Roughly 0.333—0.4 kg ethylene is produced per kilogram / -butane. Primary bv-pioducts include propylene (50 57 kg/100 kg ethylene), butadiene (7-8.5 kg/100 kg), butylenes (5-20 kg/WO kg) and aromatics (6 kg/ToO kg). 

Other. Ethylene can be produced by steam cocracking of propylene with ethane and propane. Ethylene and butenes can also be produced by catalytic disproportionation of propylene (108). 

In oil and gas refinery appHcations, titanium is used as protection in environments of H2S, SO2, CO2, NH, caustic solutions, steam, and cooling water. It is used in heat-exchanger condensers for the fractional condensation of cmde hydrocarbons, NH, propane, and desulfurization products using seawater or brackish water for cooling. 

Significant products from a typical steam cracker are ethylene, propylene, butadiene, and pyrolysis gasoline. Typical wt % yields for butylenes from a steam cracker for different feedstocks are ethane, 0.3 propane, 1.2 50% ethane/50% propane mixture, 0.8 butane, 2.8 hill-range naphtha, 7.3 light gas oil, 4.3. A typical steam cracking plant cracks a mixture of feedstocks that results in butylenes yields of about 1% to 4%. These yields can be increased by almost 50% if cracking severity is lowered to maximize propylene production instead of ethylene. 

FeedSa.tura.tlon, When gas feeds like ethane and propane are cracked, dilution steam can be added via direct humidification in towers known as feed saturators. This design reduces the load on the dilution steam system and/or medium pressure (MP) steam level. 

Vaporizing Liquids Certain liquids vaporize with heat (think of steam), and other lit]uids vaporize with a drop in pressure (think of liquid propane or freon). To eontrol vaporizing liquids so they don t change phase in the seal chamber. 

A flare performance chart for the hydrocarbon being flared, should be consulted for additional guidelines on flare tip design. Figure 3 provides a provisional performance chart for propane. The chart defines the design envelop of exit velocities and steam ratios necessary to avoide smoke formation, excessive noise, flame boilover and flame lift-off. 

Higher molecular weight hydrocarbons present in natural gases are important fuels as well as chemical feedstocks and are normally recovered as natural gas liquids. For example, ethane may be separated for use as a feedstock for steam cracking for the production of ethylene. Propane and butane are recovered from natural gas and sold as liquefied petroleum gas (LPG). Before natural gas is used it must be processed or treated to remove the impurities and to recover the heavier hydrocarbons (heavier than methane). The 1998 U.S. gas consumption was approximately 22.5 trillion ft. ... 

Chemicals directly based on propane are few, although as mentioned, propane and LPG are important feedstocks for the production of olefins. Chapter 6 discusses a new process recently developed for the dehydrogenation of propane to propylene for petrochemical use. Propylene has always been obtained as a coproduct with ethylene from steam cracking processes. Chapter 6 also discusses the production of aromatics from LPG through the Cyclar process. ... 

Butane is primarily used as a fuel gas within the LPG mixture. Like ethane and propane, the main chemical use of butane is as feedstock for steam cracking units for olefin production. Dehydrogenation of n-butane to butenes and to butadiene is an important route for the production of synthetic rubber. n-Butane is also a starting material for acetic acid and maleic anhydride production (Chapter 6). 

Like ethylene, propylene (propene) is a reactive alkene that can be obtained from refinery gas streams, especially those from cracking processes. The main source of propylene, however, is steam cracking of hydrocarbons, where it is coproduced with ethylene. There is no special process for propylene production except the dehydrogenation of propane. 

Cracking n-hutane is also similar to ethane and propane, hut the yield of ethylene is even lower. It has been noted that cracking either propane or butanes at nearly similar severity produced approximately equal liquid yields. Mixtures of propane and butane LPG are becoming important steam cracker feedstocks for C2-C4 olefin production. It has been forecasted that world LPG markets will grow from 114.7 million metric tons/day in 1988 to 136.9 MMtpd in the year 2000, and the largest portion of growth will be in the chemicals field. 

A major use of propane recovered from natural gas is the production of light olefins by steam cracking processes. However, more chemicals can be obtained directly from propane by reaction with other reagents than from ethane. This may be attributed to the relatively higher reactivity of propane than ethane due to presence of two secondary hydrogens, which are easily substituted. 

---