Standards, safety requirements

Eliminates or controls worker Site work zones and safety standards safety requirements... 

ANSI A14.5, American National Standard, Safety Requirements for Portable Reinforced Plastic (ALI)... 

EN 60065 European Standard. Safety requirements for mains operated electronic and related apparatus for household and similar general use. 

The Packaging Machinery Manufacturers Institute is the secretariat for the standard Safety Requirements for Packaging and Packaging-Related Converting Machinery. A revision of B 155.1 was approved by ANSI in July 2006 it replaced the version issued in 2000. In part, this is the guidance given on the use of the The Hazard Control Hierarchy, a five-step process ... 

ANSI K61.1, American National Standard Safety Requirements for the Storage and Handling of Anhydrous Ammonia (CGA G-2.1)[14]. 

Further information on appurtenances and markings for these tanks, and on other requirements for nurse tanks and applicator tanks, is given in CGA G-2, Anhydrous Ammonia, [6] See also ANSI K61.1, American National Standard Safety Requirements for the Storage and Handling of Anhydrous Ammonia. [3]... 

Besides reliability, "fail-safe" design and all other standard safety requirements, the magnet power supply shall also meet the following requirements ... 

American Insurance Association (AIA) 85 John Street New York, NY 10038 Handbook of Industrial Safety Standards, AssoersiXionoi Q2LSuS. ty 2iad Surety Companies, New York, 1962. Compilation of industrial safety requirements based on codes and recommendations of the ANSI, the National Eire Protection Association (now part of AIA), the ASME, and several government agencies. 

Exceptions to the preceding requirements would apply where explosionproof equipment is needed building ceiling heights are such that the standard 3.7-m (12-ft) lift is all that wih ever be needed and loads will never exceed 1 to 1.5 tons. Safety requirements for lift trucks are mandated by OSHA, by NIOSH (National Institute of Occupational Safety and Health), by State Depts. of Labor, and often by individual company standards. Among these requirements are backup-movement signals, seat belts, overhead framework for pro-... 

NFPA 70E Standard for Electrical Safety Requirements for Employee Workplaces. 

NASA Engineering Management Council (EMC) 1995 Preliminary NASA Standard, General Requirements for Structural Design and Test Factors of Safety. 1 August (http // amsd-www.larc.nasa.gov/amsd/refs/fac saf.html). 

There are also differing standards between the markets in each of these countries. For instance, the telecom market has vastly different safety requirements than the patient-contact medical market. So, it is important to determine the target market early in the product design process. These market differences will also be included in the lEC standards harmonizing efforts. 

American National Standards Institute (ANSI) Recommendation Z117.1-1989, Safety Requirements of Confined Spaces. ... 

The OSHA standard is required by the Clean Air Aet Amendments, as is the Environmental Proteetion Ageney s Risk Management Plan, whieh was proposed in 1992. Employers who merge the two sets of requirements into their proeess safety management program will better assure full eomplianee with eaeh as well as enhanee their relationship with the loeal eommunity. 

Standards and codes have very speeific safety requirements for Uie design of tanks for flaimiiable liquids or gases and pressurized chemicals such as aimnonia. Overpressure devices and vents are included in Uie design. Tank and vessel supports should be built for the ma.ximum intended load. 

Where the standard is for compliance with a safety requirement, a certificate to this effect should be provided, and may be demanded by insurers. 

Processing equipment has standard procedures to operate and meet safety requirements. Safety information and standards are available from various sources that include the equipment suppliers, Society of Plastics Industry (SPI), and American National Standards Institute (ANSI). For the past century we have observed increasing activity on the... 

While there may be places where a shower is not needed, one or more eyewash stations will almost always be required. Some laboratories, in fact, provide a small eyewash device at every sink. Combination shower and eyewash units are also available. Home-made devices are not satisfactory. A standard safety shower gives off a drenching stream of water of much higher volume than a home-type shower. An eyewash emits a large volume of water at a gentle pressure to prevent eye injury. 

The long-term widespread use of DDT over a number of years demonstrates one typical Soviet trick - abusing loopholes in the rules. DDT was actively used for decades, while not being on lists of permitted substances, a situation condoned by the Health and Epidemiological Services and their on-site agencies. Pesticide use systematically was not in accordance with the permissible standards in the USSR. In 1976 the USSR introduced a System of Labor Safety Standards Harmful Substances, Classification and Overall Safety Requirements, according to which all harmful substances were broken down into four risk classes, taking into account several different indices (table 1.5). 

Establish by a consensus of the national codes and standards development organizations such as the CDO or SDO that will have the lead in the development of codes and standards for establishing safety requirements for specific components, subsystems, and systems (as shown in the templates) and the organizations that will work collaboratively with (or in support of) the lead organization. 

Identify applicable codes and standards (specific safety requirements) and make them more accessible to permitting officials... 

---