Solvents liquid electrolytes

Electrolytes, whether solid or liquid, are comprised of the following components an electrolyte salt, which can furnish ions for charge transport and an electrolyte medium, such as a solvent (liquid electrolyte) or polymer or other matrix (solid electrolyte). For nonaqueous liquid electrolytes, solvents such as acetonitrile. 

The pyridinium- and the imidazolium-based chloroaluminate ionic liquids share the disadvantage of being reactive with water. In 1990, Mike Zaworotko (Eigure 1.4) took a sabbatical leave at the Air Eorce Academy, where he introduced a new dimension to the growing field of ionic liquid solvents and electrolytes. 

Interest in using ionic liquid (IL) media as alternatives to traditional organic solvents in synthesis [1 ], in liquid/liquid separations from aqueous solutions [5-9], and as liquid electrolytes for electrochemical processes, including electrosynthesis, primarily focus on the unique combination of properties exhibited by ILs that differentiate them from molecular solvents. 

Of course these requirements cannot be fulfilled simultaneously. For example, a low vapor pressure of the liquid electrolyte is obtained only by using more viscous dipolar aprotic solvents such as propylene carbonate, but high solvent viscosity generally entails a low conductivity. Nevertheless, a large number of useful solvents and electrolytes is available, allowing a sufficiently good approximation to an ideal electrolyte. 

As electrochemists, our interest is attracted by the electrochemical properties of materials based on conducting polymers. The study of these properties requires putting a dry material inside an electrolyte. Since most of the electrolytes employed are based on a salt that is first dissolved in a solvent, we will refer to liquid electrolytes. At the end of this chapter we... 

The prototype DSCs used liquid electrolytes, typically L/I2 in an organic solvent such as propylene carbonate. The electron generation/collection problem in this cell has been discussed analytically with the help of intensity-modulated photocurrent and photovoltage spectroscopy [314]. A particularly challenging issue has been the replacement of the liquid electrolyte with a solid charge-transport material... 

For interfaces between liquid electrolytes, we can distinguish three cases (1) interfaces between similar electrolytes, (2) interfaces between dissimilar but miscible electrolytes, and (3) interfaces between immiscible electrolytes. In the first case the two electrolytes have the same solvent (medium), but they differ in the nature and/or concentration of solutes. In the second case the interface separates dissimilar media (e.g., solutions in water and ethanol). An example for the third case is a system consisting of salt solutions in water and nitrobenzene. The interface between immiscible dissimilar liquid electrolytes is discussed in more detail in Chapter 32. 

Polymer gels and ionomers. Another class of polymer electrolytes are those in which the ion transport is conditioned by the presence of a low-molecular-weight solvent in the polymer. The most simple case is the so-called gel polymer electrolyte, in which the intrinsically insulating polymer (agar, poly(vinylchloride), poly(vinylidene fluoride), etc.) is swollen with an aqueous or aprotic liquid electrolyte solution. The polymer host acts here only as a passive support of the liquid electrolyte solution, i.e. ions are transported essentially in a liquid medium. Swelling of the polymer by the solvent is described by the volume fraction of the pure polymer in the gel (Fp). The diffusion coefficient of ions in the gel (Dp) is related to that in the pure solvent (D0) according to the equation ... 

Reactions (5.5.30) and (5.5.31) proceed prevailingly during intercalation from solid or polymer electrolytes (cf. Section 2.6) or melts. When using common liquid electrolyte solutions, a co-insertion of solvent molecules (and/or intercalation of solvated ions) very often occurs. The usual products of electrochemical intercalation are therefore ternary compounds of a general composition ... 

Very recently, we reported liquid imidazole-borane complexes (scheme 5)57 that are air stable. Judging from their polarity and viscosity (Table 3), they are expected to be a new class of solvent or electrolyte. Preparation of polymer homo-logues of imidazole-alkylborane complexes will also be reported elsewhere in the near future. 

Due to easier handling, liquid electrolyte additives and solvents have found more interest than gaseous additives. Among these components, organic sulfites [14-19] (Fig. 11), partially fluorinated aprotic solvents [12, 20-25], and vinylene additives [24, 26-32] have found particular attention. 

The local compostion model is developed as a symmetric model, based on pure solvent and hypothetical pure completely-dissociated liquid electrolyte. This model is then normalized by infinite dilution activity coefficients in order to obtain an unsymmetric local composition model. Finally the unsymmetric Debye-Huckel and local composition expressions are added to yield the excess Gibbs energy expression proposed in this study. 

We then adopt the pure solvent as the reference state for the solvent, and a hypothetical pure completely-dissociated liquid electrolyte as the reference state for the electrolyte. The reference Gibbs energies per mole are then ... 

Other references in Table in discuss applications in precipitation of metal.compounds, gaseous reduction of metals from solution, equilibrium of copper in solvent extraction, electrolyte purification and solid-liquid equilibria in concentrated salt solutions. The papers by Cognet and Renon (25) and Vega and Funk (59) stand out as recent studies in which rational approaches have been used for estimating ionic activity coefficients. In general, however, few of the studies are based on the more recent developments in ionic activity coefficients. 

Solvent Liquid range CC) Dielectric constant Viscosity Supporting (cP) electrolytes ... 

Molar conductivity measurements are equally applicable to both solid and liquid electrolytes. In contrast, the measurement of current flowing through an electrochemical cell on a time scale of minutes or hours while the cell is perturbed by a constant dc potential is only of value for solid solvents (Bruce and Vincent, 1987) where convection is absent. Because of the unique aspects of dc polarisation in a solid solvent this topic is treated in some detail in this chapter. Let us begin by considering a cell of the form ... 

Solid polymer and gel polymer electrolytes could be viewed as the special variation of the solution-type electrolyte. In the former, the solvents are polar macromolecules that dissolve salts, while, in the latter, only a small portion of high polymer is employed as the mechanical matrix, which is either soaked with or swollen by essentially the same liquid electrolytes. One exception exists molten salt (ionic liquid) electrolytes where no solvent is present and the dissociation of opposite ions is solely achieved by the thermal disintegration of the salt lattice (melting). Polymer electrolyte will be reviewed in section 8 ( Novel Electrolyte Systems ), although lithium ion technology based on gel polymer electrolytes has in fact entered the market and accounted for 4% of lithium ion cells manufactured in 2000. On the other hand, ionic liquid electrolytes will be omitted, due to both the limited literature concerning this topic and the fact that the application of ionic liquid electrolytes in lithium ion devices remains dubious. Since most of the ionic liquid systems are still in a supercooled state at ambient temperature, it is unlikely that the metastable liquid state could be maintained in an actual electrochemical device, wherein electrode materials would serve as effective nucleation sites for crystallization. 

Another important merit of the in situ gellification , rarely mentioned by various authors in the literature, is that the limitation on electrolyte composition can be relaxed. In the traditional process of making a GPE, the liquid electrolyte has to be heated with the polymer host to form the gel, during which the thermal instability of the lithium salt (LiPFe or LiBF4) and the volatility of the solvents (DMC, EMC, etc) could possibly cause the resultant GPE to deviate from the desired composition or even to degrade. It is for this reason that in most of the literature on GPE the liquid electrolytes have to be based on Lilm, LiBeti as salts, and EC/PC as solvents. In Bellcore technology, on the contrary, the state-of-the-art electrolytes, the typical of which is LiPFe/EC/DMC, could be used, since gellification occurs only after the cells are assembled. ... 

Apparently, the formation of the microporous structure within the PVdF—HFP copolymer was of critical importance to the success of Bellcore technology, and the ion conductivity was proportional to the uptake of the liquid electrolyte. To achieve the desired porosity of PVdF film, Bellcore researchers prepared the initial polymer blend of PVdF with a plasticizer dibutylphthalate (DBP), which was then extracted by low boiling solvents after film formation. Thus, a pore-memory would be left by the voids that were previously occupied by DBP. However, due to the incomplete dissolution of such high-melting DBP during the extraction process, the pore-memory could never be restored at 100% efficiency. Beside the total volume of pores thus created by the plasticizer. 

Abraham et al. were the first ones to propose saturating commercially available microporous polyolefin separators (e.g., Celgard) with a solution of lithium salt in a photopolymerizable monomer and a nonvolatile electrolyte solvent. The resulting batteries exhibited a low discharge rate capability due to the significant occlusion of the pores with the polymer binder and the low ionic conductivity of this plasticized electrolyte system. Dasgupta and Ja-cobs patented several variants of the process for the fabrication of bonded-electrode lithium-ion batteries, in which a microporous separator and electrode were coated with a liquid electrolyte solution, such as ethylene—propylenediene (EPDM) copolymer, and then bonded under elevated temperature and pressure conditions. This method required that the whole cell assembling process be carried out under scrupulously anhydrous conditions, which made it very difficult and expensive. 

Solvents, base electrolytes As solvents for the organic phase, liquids with relative dielectric constants above 10 are suitable. So far, nitrobenzene has been used almost exclusively, but dichloroethane can also be employed [7]. Tetra-butylammonium tetraphenylborate [ 1 ] is the most commonly used base... 

The method of complete electrolysis is also important in elucidating the mechanism of an electrode reaction. Usually, the substance under study is completely electrolyzed at a controlled potential and the products are identified and determined by appropriate methods, such as gas chromatography (GC), high-performance liquid chromatography (HPLC), and capillary electrophoresis. In the GC method, the products are often identified and determined by the standard addition method. If the standard addition method is not applicable, however, other identification/determination techniques such as GC-MS should be used. The HPLC method is convenient when the product is thermally unstable or difficult to vaporize. HPLC instruments equipped with a high-sensitivity UV detector are the most popular, but a more sophisticated system like LC-MS may also be employed. In some cases, the products are separated from the solvent-supporting electrolyte system by such processes as vaporization, extraction and precipitation. If the products need to be collected separately, a preparative chromatographic method is use-... 

---