Solvent ethanol-toluene

Anilines, bis(2-amino-4-chlorophenyl)disulfide, naphthylamine, 2- and 3-aminopyridines, 2-aminopyrimidines, 2-, 3-, 5-, 6-, 7-, and 8-aminoquino-lines, 6-aminocoumarin, and 2-aminopyrazine were reacted in the absence or presence of a solvent (ethanol, toluene) with ethyl orthoformate and isopropylidene or 4-heptylidene malonates to give alkylidene (het)aryl-aminomethylenemalonates (442, R = R2 = Me, Pr) in 32-100% yields [69BRP1147759 75USP3907798 88JAP(K)239269]. p-Toluenesulfonic acid monohydrate was sometimes applied as catayst. 

In this scheme L stands for triarylphosphines and S for solvent (ethanol, toluene). The alkene is simply ethene. The first step in this sequence is the dissociation of one ligand L which is replaced by a solvent molecule. Several... 

Solubility in other solvents Ethanol, toluene No data... 

Other derivatives can be prepared by reaction of the alcohol with an acid anhydride. For example, phthalic or 3-nitrophthalic anhydride (I mol) and the alcohol (Imol) are refluxed for half to one hour in a non-hydroxylic solvent, e.g. toluene or alcohol-free chloroform, and then cooled. The phthalate ester crystallises out, is precipitated by the addition of low boiling petroleum ether or is isolated by ev toration of the solvent. It is recrystallised from water, 50% aqueous ethanol, toluene or low boiling petroleum ether. Such an ester has a characteristic melting point and the alcohol can be recovered by acid or alkaline hydrolysis. 

Readily soluble in organic solvents ethanol 51, acetone 77,toluene 63, n-octanol 13, n-hexane 0.53 g per 100 mL Colorless to white solidified melt, no dissociation constant in an accessible pH range, octanol/water partition coefficient (log /Cow) 4.07 at 25 °C. 

Lussier [71] has given an overview of Uniroyal Chemical s approach to the analysis of compounded elastomers (Scheme 2.2). Uncured compounds are first extracted with ethanol to remove oils for subsequent analysis, whereas cured compounds are best extracted with ETA (ethanol/toluene azeotrope). Uncured compounds are then dissolved in a low-boiling solvent (chloroform, toluene), and filler and CB are removed by filtration. When the compound is cured, extended treatment in o-dichlorobenzene (ODCB) (b.p. 180 °C) will usually suffice to dissolve enough polymer to allow its separation from filler and CB via hot filtration. Polymer identification was based on IR spectroscopy (key role), CB analysis followed ASTM D 297, filler analysis (after direct ashing at 550-600 °C in air) by means of IR, AAS and XRD. Antioxidant analysis proceeded by IR examination of the nonpolymer ethanol or ETA organic extracts. For unknown AO systems (preparative) TLC was used with IR, NMR or MS identification. Alternatively GC-MS was applied directly to the preparative TLC eluent. 

Anon., Univ. Safety Assoc., Safety Newsletter, 1982-1984 A solution of the chloride (120 ml) in toluene (750 ml) was treated (apparently without effective stirring) with excess sodium bicarbonate solution to destroy it. When reaction had ceased, the organic layer was poured into a waste solvent drum. Vigorous evolution of sulfur dioxide and hydrogen chloride then ensued from reaction with ethanol (toluene-soluble) in the waste drum. For destruction of solutions of sulfinyl chloride in water-insoluble solvents, extremely good agitation is necessary to ensure proper contact with a basic reagent. Ammonia is more soluble in toluene than is water, so ammonia solution should be used after bicarbonate treatment to ensure complete destruction. 

When 3(4)-substituted thiophenes (e.g., 3-hexylthiophene) are used as monomers, the polymers are partly or completely soluble in low polar organic solvents like toluene, chloroform, dichloromethane, THF. Therefore, after washing with ethanol, the polymer is dried, then dissolved in chloroform and reprecipitated into methanol or acetone to remove low-molecular-weight fractions. The solid is collected by filtration, washed with methanol, and dried in vacuo. 

Soluble in acetone, ethanol, benzene, and ether (Weast, 1986) and many other organic solvents including toluene. 

Rubber A maferial fhaf is capable of recovering from large deformations quickly and forcibly and can be, or already is, modified fo a sfafe in which if is essentially insoluble (but can swell) in boiling solvent such as benzene, methyl ethyl ketone, and ethanol-toluene azeotrope. A rubber in its modified state, free of diluents, retracts within 1 min to less than 1.5 times of its original length after being stretched at room temperature to twice its length and held for 1 min before release. 

The exchange reactions of organyltrialkoxysilanes with THEA mostly require heating of the components in an appropriate inert solvent (benzene, toluene, xylene, anisole, chloroform, methanol, ethanol etc.) for a long time. However, in some cases the reactions can be carried out at room temperature or, if necessary, with cooling. The transetherification rates and silatrane yields increase in the presence of an alkali metal hydroxide or alkoxide as a basic catalyst. 

The synthesis of sildenafil serves as an excellent example of the demands of commercial chemistry. The route described contains all of the desired attributes required in chemical development, namely a safe, robust route, a convergent synthesis and a high yielding process. The authors managed to improve the yield from 7.5 % in the medicinal chemistry to 75.8 % overall from pyrazole 3. The synthesis also has an exceptionally low environmental impact. Only toluene and ethyl acetate are organic waste while the other solvents (ethanol and tert-butanol) can be treated in the water plants. The synthesis has been... 

Aromatic plant material is placed into organic solvents such as acetone (propanone) or hexane, which dissolve out the oils. Other solvents used are methanol, ethanol, toluene and petroleum ether. In some processes the plant material is broken up, to aid penetration of solvent into the tissues, by placing it in a rotating drum with internal blades to ensure thorough mixing. The materials that become dissolved include not only the essential oil but also natural waxes, resinous materials, chlorophyll and other pigments. 

---