Solid equipment

Equation (11-48) is applicable to burdens in the solid, liquid, or gaseous phase, either static or in laminar motion it is apphcable to solidification equipment and to divided-solids equipment such as metal belts, moving trays, stationaiy vertical tubes, and stationaiy-shell fluidizers. 

Dispersed solids equipment is generally operated in a batch mode, contacting solvent and the raw plant material together for sufficient time that equilibrium concentration in the extract is approached. A mass balance on the system gives the following ... 

Drying refers to the removal of water from a substance through a whole range of processes, including distillation, evaporation, and even physical separations such as with centrifuges. Here, consideration is restricted to the removal of moisture from solids and liquids into a gas stream (usually air) by heat, namely, thermal drying. Some of the types of equipment for removal of water also can be used for removal of organic liquids from solids. 

The selection of equipment for the treatment of solid particle emissions to the atmosphere depends on a number of factors ... 

A wide range of equipment is available for the control of emissions of solid particles. These methods are classified in broad terms in Table 11.1. ... 

Kipp s apparatus Equipment for the production of a gas by interaction of a liquid and a solid. It consists of three receptacles, the top is reservoir for the liquid and is connected to the bottom. The middle contains the solid and a tap for the gas. When gas is released the liquid rises and reacts with the solid, when the tap is closed the back pressure returns the liquid lo the lower reservoir and reaction cease . Once widely used for the production of H.S (HCl and FeS) and C O (HCl and CaC(3,<). 

Posgay, G. and Imre, L. Detection of Stresses Using Multiplex Barkhausen Noise Measuring Equipment Proc. 8 th DAS on Experimental Methods in Solid Mechanics, Godollo, 1991, Edited 1.. Huszdr, pp. 19-19/2... 

This chapter and the two that follow are introduced at this time to illustrate some of the many extensive areas in which there are important applications of surface chemistry. Friction and lubrication as topics properly deserve mention in a textbook on surface chemistiy, partly because these subjects do involve surfaces directly and partly because many aspects of lubrication depend on the properties of surface films. The subject of adhesion is treated briefly in this chapter mainly because it, too, depends greatly on the behavior of surface films at a solid interface and also because friction and adhesion have some interrelations. Studies of the interaction between two solid surfaces, with or without an intervening liquid phase, have been stimulated in recent years by the development of equipment capable of the direct measurement of the forces between macroscopic bodies. 

This chapter simnnarizes the interactions that affect the spectrum, describes the type of equipment needed and the perfomiance that is required for specific experiments. As well as describing the basic experiments used in solid-state NMR, and the more advanced teclmiques used for distance measurement and correlation, some emphasis is given to nuclei with spin / > dsince the study of these is most different from liquid-state NMR. 

We are all familiar with tire tliree states of matter gases, liquids and solids. In tire 19tli century the liquid crystal state was discovered [1 and 2] tliis can be considered as tire fourtli state of matter [3].The essential features and properties of liquid crystal phases and tlieir relation to molecular stmcture are discussed here. Liquid crystals are encountered in liquid crystal displays (LCDs) in digital watches and otlier electronic equipment. Such applications are also considered later in tliis section. Surfactants and lipids fonn various types of liquid crystal phase but this is discussed in section C2.3. This section focuses on low-molecular-weight liquid crystals, polymer liquid crystals being discussed in tire previous section. 

The experimental conditions for conducting the above reaction in the presence of dimethylformamide as a solvent are as follows. In a 250 ml. three-necked flask, equipped with a reflux condenser and a tantalum wire Hershberg-type stirrer, place 20 g. of o-chloronitrobenzene and 100 ml. of diinethylform-amide (dried over anhydrous calcium sulphate). Heat the solution to reflux and add 20 g. of activated copper bronze in one portion. Heat under reflux for 4 hours, add another 20 g. portion of copper powder, and continue refluxing for a second 4-hour period. Allow to cool, pour the reaction mixture into 2 litres of water, and filter with suction. Extract the solids with three 200 ml. portions of boiling ethanol alternatively, use 300 ml. of ethanol in a Soxhlet apparatus. Isolate the 2 2- dinitrodiphenyl from the alcoholic extracts as described above the 3ueld of product, m.p. 124-125°, is 11 - 5 g. 

Concurrently with the preparation of the phenyldiazonium chloride solution, prepare a cold suspension of sodium arsenite. Place 250 ml. of water in a 3-htre round-bottomed flask equipped with a mechanical stirrer. Heat the water to boding, add 125 g. of anhydrous sodium carbonate, and, as soon as the carbonate has dissolved, introduce 62 5 g. of pure arsenious oxide and 3 g. of crystallised copper sulphate with stirring. When all the solids have dissolved, cool the solution with stirring under a stream of tap water until the temperature has fallen to 15°. 

Equip a I litre three-necked flask with a mechanical stirrer and a thermometer, and immerse the flask in a bath of ice and salt. Place 306 g. (283 ml.) of acetic anhydride, 300 g. (285 ml.) of glacial acetic acid and 25 g. of p-nitrotoluene in the flask, and add slowly, with stirring, 42 5 ml. of concentrated sulphuric acid. When the temperature has fallen to 5°, introduce 50 g. of A.R. chromic anhydride in small portions at such a rate that the temperature does not rise above 10° continue the stirring for 10 minutes after all the chromium trioxide has been added. Pour the contents of the flask into a 3 litre beaker two-thirds filled with crushed ice and almost fill the beaker with cold water. Filter the solid at the pump and wash it with cold water until the washings are colourless. Suspend the product in 250 ml. of cold 2 per cent, sodium carbonate solution and stir mechanically for 10-15 minutes filter (1), wash with cold water, and finally with 10 ml. of alcohol. Dry in a vacuum desiccator the yield of crude p-nitrobenzal diacetate is 26 g. (2),... 

In a 500 ml. wide-mouthed reagent bottle place a cold solution of 25 g. of sodium hydroxide in 250 ml. of water and 200 ml. of alcohol (1) equip the bottle with a mechanical stirrer and surround it with a bath of water. Maintain the temperature of the solution at 20-25°, stir vigorously and add one-half of a previously prepared mixture of 26-5 g. (25 -5 ml.) of purebenzaldehyde (Section IV,115) and 7 -3 g. (9-3 ml.) of A.R. acetone. A flocculent precipitate forms in 2-3 minutes. After 15 minutes add the remainder of the benzaldehyde - acetone mixture. Continue the stirring for a further 30 minutes. Filter at the pump and wash with cold water to eliminate the alkali as completely as possible. Dry the solid at room temperature upon filter paper to constant weight 27 g. of crude dibenzalacetone, m.p. 105-107°, are obtained. Recrystallise from hot ethyl acetate (2-5 ml. per gram) or from hot rectified spirit. The recovery of pure dibenzalacetone, m.p. 112°, is about 80 per cent. 

---