Sodium nitrite diazonium

They are prepared by the action of HNO2 on aromatic amines. The amine is dissolved in excess of mineral acid and sodium nitrite is added slowly until a slight excess of HNO2 is present. The reaction is usually carried out in ice-cold solution. The solution then contains the diazonium salt of the mineral acid used, anhydrous diazonium salts of unpredictable stability may be precipitated with complex anions like PF , SnCl6 BF4 . 

The solution of the aniline hydrochloride should be cooled to 5°C., and this temperature maintained throughout the addition of the sodium nitrite solution. External cooling has to be maintained, otherwise the heat of the reaction would cause the temperature to rise, with the consequent decomposition of the diazonium chloride and the production of phenol. If, on the other hand, the temperature is reduced to about o , diazotisation becomes extremely slow and unchanged nitrous acid may remain in the solution for an impracticably long time. 

Sufficient sodium nitrite must be added to diazotise all the aniline present, otherwise the unchanged aniline will react with the diazonium chloride to give diazoaminobenzene (p. 187) ... 

Dissolve 15 ml. (15-4 g.) of aniline in a mixture of 40 ml. of concentrated hydrochloric acid and 40 ml. of water contained in a 250 ml. conical flask. Place a thermometer in the solution, immerse the flask in a mixture of ice and water, and cool until the temperature of the stirred solution reaches 5°. Dissolve I2 5 g. of powdered sodium nitrite in 30 ml. of water, and add this solution in small quantities (about 2-3 ml. at a time) to the cold aniline hydrochloride solution, meanwhile keeping the latter well stirred by means of a thermometer. Heat is evolved by the reaction, and therefore a short interval should be allowed between consecutive additions of the sodium nitrite, partly to allow the temperature to fall again to 5°, and partly to ensure that the nitrous acid formed reacts as completely as possible with the aniline. The temperature must not be allowed to rise above 10°, otherwise appreciable decomposition of the diazonium compound to phenol will occur on the other hand, the temperature... 

When hydrochloric acid is cautiously added to an aqueous solution containing both sodium nitrite and the sodium salt of sulphanilic acid, NaOsSCgH NH, the amino group of the latter undergoes normal diazotisation, giving the diazonium chloride (A). The latter, however, ionises in solution, giving sodium and chloride ions and the internal salt (B), which possesses two opposite charges and is therefore neutral this internal salt is stable under... 

Azo-dye formation. Dissolve 2-3 drops of aniline in 1 ml. of cone. HCl and add 3 ml. of water. Shaike to dissolve any hydrochloride which may have separated and cool in ice. Add a few drops of 20% sodium nitrite solution. Add this cold diazonium solution to a cold solution of the phenol in an excess of aqueous NaOH solution. Solutions or precipitates of azo-dyes ranging in colour from orange through scarlet to dark red, according to the phenol used, are obtained. Note in particular that i-naphthol gives a brownish-red, 2-naphthol a scarlet precipitate. Catechol decomposes. 

Diazotisation. Dissolve 0 2 g. of anthranilic acid in about 4 ml. of dil. HCl and cool in ice-water. To this solution, add slowly about I ml. of cold 20% sodium nitrite. solution and divide the cold diazonium solution thus prepared into two portions A and B. 

Diazotisation. Dissolve 0 2 g. of the substance in about 5 ml. of dil. HCl, warming if necessary. Cool in ice-water and add sodium nitrite solution drop by drop the end of the diazotisation is marked by the complete decolorisation of the solution. Pour the diazonium solution into a cold solution of 2-naphthol in a considerable excess of NaOH solution a brilliant red dye is produced. 

Note on the laboratory preparation of monoethylaniline. Although the laboratory preparation of monomethyl- or monoethyl-aniline is hardly worth whUe, the following experimental details may be useful to those who wish to prepare pure monoethylaniline directly from amline. In a flask, fitted with a double surface reflux condenser, place 50 g. (49 ml.) of aniline and 65 g. of ethyl bromide, and boU gently for 2 hours or until the mixture has almost entirely sohdified. Dissolve it in water and boil off the small quantity of unreacted ethyl bromide. Render the mixture alkaUne with concentrated sodium hydroxide solution, extract the precipitated bases with three 50 ml. portions of ether, and distil off the ether. The residual oil contains anihne, mono- and di-ethylaniline. Dissolve it in excess of dilute hydrochloric acid (say, 100 ml. of concentrated acid and 400 ml. of water), cool in ice, and add with stirring a solution of 37 g. of sodium nitrite in 100 ml. of water do not allow the temperature to rise above 10°. Tnis leads to the formation of a solution of phenyl diazonium chloride, of N-nitrosoethylaniline and of p-nitrosodiethylaniline. The nitrosoethylaniline separates as a dark coloured oil. Extract the oil with ether, distil off the ether, and reduce the nitrosoamine with tin and hydrochloric acid (see above). The yield of ethylaniline is 20 g. 

The experimental conditions necessary for the preparation of a solution of a diazonium salt, diazotisation of a primary amine, are as follows. The amine is dissolved in a suitable volume of water containing 2 5-3 equivalents of hydrochloric acid (or of sulphuric acid) by the application of heat if necessary, and the solution is cooled in ice when the amine hydrochloride (or sulphate) usually crystallises. The temperature is maintained at 0-5°, an aqueous solution of sodium nitrite is added portion-wise until, after allowing 3-4 minutes for reaction, the solution gives an immediate positive test for excess of nitrous acid with an external indicator—moist potassium iodide - starch paper f ... 

An interesting application of the diazo reaction is to the preparation of the otherwise difficultly accessible o- and />-dinitrobenzenes o- or p-rutrophenyl-diazonium fluoborates react with sodium nitrite in the presence of copper powder to yield o- or p-dinitrobenzene ... 

Dissolve 36 g. of p-toluidine in 85 ml. of concentrated hydrochloric acid and 85 ml. of water contained in a 750 ml. conical flask or beaker. Cool the mixture to 0° in an ice-salt bath with vigorous stirring or shaking and the addition of a httle crushed ice. The salt, p-toluidine hydrochloride, will separate as a finely-divided crystalline precipitate. Add during 10-15 minutes a solution of 24 g. of sodium nitrite in 50 ml. of water (1) shake or stir the solution well during the diazotisation, and keep the mixture at a temperature of 0-5° by the addition of a httle crushed ice from time to time. The hydrochloride wUl dissolve as the very soluble diazonium salt is formed when ah the nitrite solution has been introduced, the solution should contain a trace of free nitrous acid. Test with potassium iodide - starch paper (see Section IV,60). 

Chlorobenzene. Prepare a solution of phenyldiazonium chloride from 31 g. (30 -5 ml.) of aniUne, 85 ml. of concentrated hydrochloric acid, 85 ml, of water, and a solution of 24 g. of sodium nitrite in 50 ml. of water (for experimental details, see Section IV,60). Prepare cuprous chloride from 105 g. of crystallised copper sulphate (Section 11,50,1), and dissolve it in 170 ml. of concentrated hydrochloric acid. Add the cold phenyl diazonium chloride solution with shaking or stirring to the cold cuprous chloride solution allow the mixture to warm up to room temperature. Follow the experimental details given above for p-chlorotoluene. Wash the chlorobenzene separated from the steam distillate with 40 ml. of 10 per cent, sodium hydroxide solution (to remove phenol), then with water, dry with anhydrous calcium chloride or magnesium sulphate, and distil. Collect the chlorobenzene (a colourless liquid) at 131-133° (mainly 133°), The yield is 29 g. 

Dissolve 46-5 g. (45-5 ml.) of aniUne in a mixture of 126 ml. of concentrated hydrochloric acid and 126 ml. of water contained in a 1-htre beaker. Cool to 0-5° in a bath of ice and salt, and add a solution of 36-5 g. of sodium nitrite in 75 ml. of water in small portions stir vigorously with a thermometer (1) and maintain the temperature below 10°, but preferably at about 5° by the addition of a httle crushed ice if necessary. The diazotisation is complete when a drop of the solution diluted with 3-4 drops of water gives an immediate blue colouration with potassium iodide - starch paper the test should be performed 3-4 minutes after the last addition of the nitrite solution. Prepare a solution of 76 g. of sodium fluoborate (2) in 150 ml. of water, cool, and add the chilled solution slowly to the diazonium salt solution the latter must be kept well stirred (1) and the temperature controlled so that it is below 10°. Allow to stand for 10 minutes with frequent stirring. Filter... 

Difluorodiphenyl. Bis-diazotise a solution of 46 g. of benzidine (Section IV,88) in 150 ml. of concentrated hydrochloric acid and 150 ml. of water by means of a solution of 35 g. of sodium nitrite in 60 ml. of water add about 200 g. of crushed ice during the process (compare p-Fbtorotoluene above). Filter the solution and add it to a filtered solution of 85 g. of sodium borofluoride in 150 ml. of water. Stir for several minutes, collect the precipitated bis-diazonium borofluoride by suction filtration, wash with 5 ml. of ice-cold water, and dry at 90-100°. Place the dry salt in a flask fitted with an air condenser, immerse the flask in an oil bath, and slowly raise the temperature to 150° (Fume Cupboard ). When decomposition of the salt is complete, steam distil the mixture collect the 4 4 difluoro-diphenyl which passes over and recrystallise it from ethanol. The yield is 21 g., m.p. 92-93°. 

Dissolve 34 g. of o-nitroaniline in a warm mixture of 63 ml. of concentrated hydrochloric acid and 63 ml. of water contained in a 600 ml. beaker. Place the beaker in an ice - salt bath, and cool to 0-5° whilst stirring mechanically the o-nitroaniline hydrochloride will separate in a finely-divided crystalline form. Add a cold solution of 18 g. of sodium nitrite in 40 ml. of water slowly and with stirring to an end point with potassium iodide - starch paper do not allow the temperature to rise above 5-7 . Introduce, whilst stirring vigorously, a solution of 40 g. of sodium borofluoride in 80 ml. of water. Stir for a further 10 minutes, and filter the solid diazonium fluoborate with suction on a sintered glass funnel. Wash it immediately once with 25 ml. of cold 5 per cent, sodium borofluoride solution, then twice with 15 ml. portions of rectified (or methylated) spirit and several times with ether in each washing stir... 

Dissolve 200 g. of sodium nitrite in 400 ml. of water in a 2-litre beaker provided with an efficient mechanical stirrer, and add 40 g. of copper powder (either the precipitated powder or copper bronze which has been washed with a little ether). Suspend the fluoborate in about 200 ml. of water and add it slowly to the well-stirred mixture. Add 4-5 ml. of ether from time to time to break the froth. The reaction is complete when all the diazonium compound has been added. Transfer the mixture to a large flask and steam distil until no more solid passes over (about 5 litres of distillate). Filter off" the crystalline solid in the steam distillate and dry upon filter paper in the air this o-dinitrobenzene (very pale yellow crystals) has m.p. 116° (t.c., is practically pure) and weighs 29 g. It may be recrystallised from alcohol the recrystallised solid melts at 116-5°. 

Grind 25 g. of anthraniUc acid with 46 ml. of concentrated hydrochloric acid and 75 ml. of water in a glass mortar, and transfer the suspension to a 500 ml. round-bottomed flask which is provided with a mechanical stirrer. Cool the contents of the flask in an ice bath to 0-5°, and add a solution of 13-2 g. of sodium nitrite in 175 ml. of water from a dropping fimnel during about 20 minutes. Keep the diazonium solution below 6° and, if it is not clear, filter it by suction through a chilled Buchner funnel immediately before use. 

Attention has previously (see Diazonium Sails) been drawn to the fact that unless an excess of hydrochloric (or mineral) acid is used in the diazotisation process, coupling occurs between the diazonium salt and the amine to give diazoamino compounds. Thus phenyldiazonium chloride and aniline yield diazoaminobenzene. This substance may be conveniently prepared by dissolving two equivalents of aniline in three equivalents of hydrochloric acid, and adding one equivalent of sodium nitrite in aqueous solution followed by two equivalents of sodium acetate ... 

Chlorodiphenyl. Diazotise 32 g. of o-chloroaniline (Section IV,34) in the presence of 40 ml. of concentrated hydrochloric acid and 22 -5 ml. of water in the usual manner (compare Section IV,61) with concentrated sodium nitrite solution. Transfer the cold, filtered diazonium solution to a 1 5 htre bolt-head flask surrounded by ice water, introduce 500 ml. of cold benzene, stir vigorously, and add a solution of 80 g. of sodium acetate trihydrate in 200 ml. of water dropwise, maintaining the temperature at 5-10°. Continue the stirring for 48 hours after the first 3 hours, allow the reaction to proceed at room temperature. Separate the benzene layer, wash it with water, and remove the benzene by distillation at atmospheric pressure distil the residue under reduced pressure and collect the 2-chlorodiphenyl at 150-155°/10 mm. The yield is 18 g. Recrystalliae from aqueous ethanol m.p. 34°. 

Triiodobeiizoic acid. Dissolve 6-8 g. of 3 5-diiodo-4-aminobenzoic acid in 30 ml. of cold concentrated sulphuric acid, add a large excess (3 0 g.) of powdered sodium nitrite, and allow the mixture to stand at 0° for 2 hours. Treat the cold diazonium solution with a solution of 17 0 g. of potassium iodide in 40 ml. of water a dark red precipitate separates. Warm the mixture on a water bath until the evolution of nitrogen ceases, and remove any residual iodine with a little... 

Nitrosation (Section 22 15) Nitrosation of amines occurs when sodium nitrite is added to a solution containing an amine and an acid Primary amines y e d alkyl diazonium salts Alkyl diazonium salts are very unstable and yield carbo cation derived products Aryl diazonium salts are exceedingly useful synthetic in termediates Their reactions are de scribed in Table 22 7... 

Fluoroaromatics are produced on an industrial scale by diazotization of substituted anilines with sodium nitrite or other nitrosating agents in anhydrous hydrogen fluoride, followed by in situ decomposition (fluorodediazoniation) of the aryldiazonium fluoride (21). The decomposition temperature depends on the stabiHty of the diazonium fluoride (22,23). A significant development was the addition of pyridine (24), tertiary amines (25), and ammonium fluoride (or bifluoride) (26,27) to permit higher decomposition temperatures (>50° C) under atmospheric pressure with minimum hydrogen fluoride loss. 

Synthesis. Almost without exception, azo dyes ate made by diazotization of a primary aromatic amine followed by coupling of the resultant diazonium salt with an electron-rich nucleophile. The diazotization reaction is carried out by treating the primary aromatic amine with nitrous acid, normally generated in situ with hydrochloric acid and sodium nitrite. The nitrous acid nitrosates the amine to generate the N-nitroso compound, which tautomerizes to the diazo hydroxide. 

Amino-6-chloro-4-methyl- and 3-amino-6-chloro-5-methyl-pyridazine and 3-amino-6-methylpyridazin-4(l//)-one are transformed with sodium nitrite in the presence of acid into the corresponding oxo compounds. If concentrated hydrochloric acid is used, in some instances the corresponding chloro derivatives are obtained as side products. On the other hand, 3-, 4-, 5- and 6-aminopyridazine 1-oxides and derivatives are transformed into stable diazonium salts, which can easily be converted into the corresponding halo derivatives. In this way 3-, 4-, 5- and 6-bromopyridazine 1-oxides, 5-chloropyridazine 1-oxide, 3,4,5-trichloropyridazine 1-oxide and 6-chloropyridazine 1-oxide can be obtained. 

The 4-chloroben2enediazon1um chloride solution Is prepared as follows finely powdered 4-chloroaniline (5.65 g, 0.044 mol) is suspended in 18 ml of 24% aqueous hydrochloric acid and cooled to O C. Sodium nitrite (3.2 g, 0.045 mol) in water (7 ml) is added dropwise during 45 min at 0-5°C to give a pale yellow solution of the diazonium salt. 

Heavily fluonnated aminobenzenes, pyridines, and pyrimidines are diazotized in strong-acid media Solid sodium nitrite added directly to the fluonnated amine dissolved in 80% hydrofluonc acid, anhydrous hydrogen fluoride, or (1 1 wt/wt) 98% sulfuric acid in (86 14 wt/wt) acetic and propionic acids affords the electrophilic fluoroarenediazonium ion Addition of an electron rich aromatic to the resultant diazonium solution gives the fluoroareneazo compound [10 II] (equa tions 9 and 10)... 

---