Sodium estimation

Usually prepared by the action of NaCN on benzaldehyde in dilute alcohol. It is oxidized by nitric acid to benzil, and reduced by sodium amalgam to hydrobenzoin PhCHOHCHOHPh by tin amalgam and hydrochloric acid to des-oxybenzoin, PhCH2COPh and by zinc amalgam to stilbene PhCH = CHPh. It gives an oxime, phenylhydrazone and ethanoyl derivative. The a-oxime is used under the name cupron for the estimation of copper and molybdenum. 

Fehling s solution A solution of copper sulphate, sodium potassium tartrate and NaOH used for estimating and detecting reducing sugars. 

C12H9N3O4. A brownish-red powder, soluble in sodium hydroxide. Used for the detection and estimation of magnesium, with which it forms a blue lake in alkaline solutions. 

An indirect estimate of surface tension may be obtained from the change in lattice parameters of small crystals such as magnesium oxide and sodium chloride owing to surface tensional compression [121] however, these may represent nonequilibrium surface stress rather than surface tension [68]. Surface stresses may produce wrinkling in harder materials [122]. 

The excess heat of solution of sample A of finely divided sodium chloride is 18 cal/g, and that of sample B is 12 cal/g. The area is estimated by making a microscopic count of the number of particles in a known weight of sample, and it is found that sample A contains 22 times more particles per gram than does sample B. Are the specific surface energies the same for the two samples If not, calculate their ratio. 

Sodium thiosulphate is an important reducing agent used in volumetric analysis for the estimation of iodine ... 

Addition of calcium nitrate solution to a fluoride gives a white precipitate of calcium fluoride, CaFj. If the latter is precipitated slowly, it can be filtered off and weighed to estimate the fluoride. Fluoride can also be determined by the addition of sodium chloride and lead nitrate which precipitate lead chlorofluoride, PbClF. This is filtered off and weighed. 

The reaction provides a method of estimating copper(Il) since the liberated iodine may be titrated with sodium thiosulphate ... 

Note. (1) Most sulphur compounds are completely oxidised if the tube is heated under the conditions described for the estimation of halogens. Sul-phonic acids and sulphones are more difficult to oxidise completely and the tube should be slowly heated to 300 and maintained at this temperature for at least 6 hours. The oxidation may be facilitated by adding a few crystals of sodium or potassium bromide to the organic material in the small tube, so that bromine shall be present to intensify the oxidation during the heating. 

Principle. An organic compound which contains chlorine is mixed with sodium peroxide and ignited in a closed metal bomb. The chlorine is thus converted to sodium chloride, and after acidification the chloride is estimated by the Volhard volumetric method. Bromine and iodine, when constituents of organic compounds similarly treated, are converted largely into sodium bromate and iodate respectively these ions are therefore subsequently reduced by hydrazine to bromide and iodide ions, and estimated as before. 

Into a 750 ml. round-bottomed flask furnished with a reflux condenser place a solution of 34 g. (18-5 ml.) of concentrated sulphuric acid in 100 ml, of water add 33 g. of di-n-butyl cyanamide and a few fragments of porous porcelain. Reflux gently for 6 hours. Cool the resulting homogeneous solution and pour in a cold solution of 52 g. of sodium hydroxide in 95 ml. of water down the side of the flask so that most of it settles at the bottom without mixing with the solution in the flask. Connect the flask with a condenser for downward distillation and shake it to mix the two layers the free amine separates. Heat the flask when the amine with some water distils continue the distillation until no amine separates from a test portion of the distillate. Estimate the weight of water in the distillate anp add about half this amount of potassium hydroxide in the form of sticks, so that it dissolves slowly. 

Predict the products formed when each of the following isotopically substituted denvatives of chlorobenzene is treated with sodium amide in liquid ammonia Estimate as quantitatively as possible the composition of the product mixture The astensk ( ) in part (a) designates C and D in part (b) is... 

The reduction potentials for the actinide elements ate shown in Figure 5 (12—14,17,20). These ate formal potentials, defined as the measured potentials corrected to unit concentration of the substances entering into the reactions they ate based on the hydrogen-ion-hydrogen couple taken as zero volts no corrections ate made for activity coefficients. The measured potentials were estabhshed by cell, equihbrium, and heat of reaction determinations. The potentials for acid solution were generally measured in 1 Af perchloric acid and for alkaline solution in 1 Af sodium hydroxide. Estimated values ate given in parentheses. 

Sodium Bicarbonate. Many soda ash plants convert a portion of their production to sodium bicarbonate [144-55-8], NaHCO. Soda ash is typically dissolved, carbonated, and cooled to crystallize sodium bicarbonate. The mother Hquor is heated and recycled. The soHd bicarbonate is dried in flash or tray driers, screened, and separated into various particle size ranges. Bicarbonate markets include food, pharmaceuticals, catde feed, and fire extinguishers. U.S. demand was approximately 320,000 t in 1989 world demand was estimated at one million metric tons. 

The concentration of aqueous solutions of the acid can be deterrnined by titration with sodium hydroxide, and the concentration of formate ion by oxidation with permanganate and back titration. Volatile impurities can be estimated by gas—Hquid chromatography. Standard analytical methods are detailed in References 37 and 38. 

Naphthalenesulfonic Acid—Formaldehyde Condensates. The sodium salts of the condensation products of naphthalenesulfonic acid with formaldehyde constitute an important class of compounds which are mainly used in the area of concrete additives (32,33), agricultural formulations, mbber formulations, and synthetic tanning agents. They are also used in photographic materials (34). Hampshire Chemical Co. and Henkel of America, Inc., are the largest suppHers of naphthalene sulfonate in concrete additives (superplasticizer) and reportedly hold 75—80% of this market. It was estimated that naphthalene sulfonate demand from U.S. producers would reach approximately... 

The U.S. domestic capacity of ammonium perchlorate is roughly estimated at 31,250 t/yr. The actual production varies, based on the requirements for soHd propellants. The 1994 production ran at about 11,200 t/yr, 36% of name plate capacity. Environmental effects of the decomposition products, which result from using soHd rocket motors based on ammonium perchlorate-containing propellants, are expected to keep increasing pubHc pressure until consumption is reduced and alternatives are developed. The 1995 price of ammonium perchlorate is in the range of 1.05/kg. Approximately 450 t/yr of NH ClO -equivalent cell Hquor is sold to produce magnesium and lithium perchlorate for use in the production of batteries (113). Total U.S. domestic sales and exports for sodium perchlorate are about 900 t/yr. In 1995, a solution containing 64% NaClO was priced at ca 1.00/kg dry product was also available at 1.21/kg. 

Anhydrous sodium tripolyphosphate is slow to hydrate in contact with the atmosphere under normal ambient conditions and generally remains free-flowing. If the relative humidity is below a critical relative humidity, which is different for both anhydrous forms of STP and dependent on temperature, hydration does not take place. For prolonged storage at room temperature, relative humidities above ca 60% in the air result in water absorption. For shorter periods, high levels of humidity can be tolerated. However, even at higher humidities, the amount of water absorbed is small. The heats evolved from vapor hydration of STP-I and -II have been estimated at 343 and 334 kj /mol (82.0 and 79.9 kcal/mol), respectively (25). 

Analysis. Dilute aqueous solutions of hydroxyhydroquiaone turn blue-green temporarily when mixed with ferric chloride. The solutions darken upon addition of small amounts, and turn red with additions of larger amounts of sodium carbonate. Derivatives used for identification are the picrate, which forms orange-red needles (mp of 96°C), and the triacetate (mp 96—97°C). Thin-layer chromatography and Hquid chromatography are well suited for the quahtative and quantitative estimation of hydroxyhydroquiaone (93,94). 

Production figures for sodium alumiaate are not released by manufacturers ia the United States. There are approximately eight commercial U.S. producers and total production was estimated at 120,000 metric tons ia 1990. Prices for large quantities of sodium alumiaate are ia the range of 0.22/kg to 0.43/kg for Hquids, depending upon concentration, location, and volume purchased. 

Alkali sihcates are used as components, rather than reactants, in many appHcations. In many cases they only contribute partially to overall performance. Utility factors are generally not as easy to identify. Their benefit usually depends on the surface and solution chemical properties of the wide range of highly hydrophilic polymeric siUcate ions deUverable from soluble sihcate products or their proprietary modifications. In most cases, however, one or two of the many possible induences of these complex anions cleady express themselves in final product performance at a level sufficient to justify their use (102). Estimates of the 1995 U.S. consumption of sodium sihcates are shown in Table 6. 

U.S. sodium bromide demand accounts for 8—10% of total bromine production. In 1994 demand is estimated to have been 13,600—17,200 metric tons (5). At mid-1996, the price for technical-grade sodium bromide iu tmckload quantities was 1.54/kg ( 0.70/lb) (6). Manufacturers of sodium bromide iuclude Albemarle, Great Lakes Chemical, Rhc )ne-Poulenc, and Whittaker Corporation. 

---