Ruhrchemie process catalysts

Eventually, the spent catalyst solution has to leave the oxo loop for work-up. The Ruhrchemie works of Celanese AG in Oberhausen (Germany) operate several rhodium-based oxo processes besides the well-known Ruhrchemie/Rhone-Poulenc process (RCF1/RP, the described low pressure oxo process with TPPTS-modified Rh catalyst), there are the Ruhrchemie process with an unmodified Rh catalyst at high pressure (comparable to the late ICI process [76] this variant is for the benefit of a high iso/n ratio... 

Table V shows the salient features of several Fischer-Tropsch processes. Two of these—the powdered catalyst-oil slurry and the granular catalyst-hot gas recycle—have not been developed to a satisfactory level of operability. They are included to indicate the progress that has been made in process development. Such progress has been quite marked in increase of space-time yield (kilograms of C3+ per cubic meter of reaction space per hour) and concomitant simplification of reactor design. The increase in specific yield (grams of C3+ per cubic meter of inert-free synthesis gas) has been less striking, as only one operable process—the granular catalyst-internally cooled (by oil circulation) process—has exceeded the best specific yield of the Ruhrchemie cobalt catalyst, end-gas recycle process. The importance of a high specific yield when coal is used as raw material for synthesis-gas production is shown by the estimate that 60 to 70% of the total cost of the product is the cost of purified synthesis gas.

Reaction in two-phase liquid-liquid systems. The Ruhrchemie process for the manufacture of butyraldehyde from propylene uses a water-soluble rhodium catalyst, while the product butyraldehyde forms an immiscible organic layer. Separation of the product from the catalyst is thus easily accomplished (see Section 5.2.5). 

The aldolic condensation of butyraldehyde occurs in the presence of caustic soda, which acts as a catalyst (Ruhrchemie process). The system operates in this case between 80 and 130 C and between 03 and 1.106 Pa absolute. The continuous removal of one molecule of water yields 2-ethylhexenal, which is hydrogenated in the presence of a nickel catalyst between 100 and 15IPC and between 5 and 10.10 Pa absolute. 

Weller (81) studied the pressure dependence of the synthesis over a cobalt-thoria-kieselguhr catalyst, at about 1 atmosphere pressure using very short contact times so that the concentration of synthesis products was very low. Under these conditions the synthesis rate increased approximately as the square root of the synthesis gas pressure. The temperature coefficient in Weller s tests corresponded to an activation energy of 26 kcal./ mole. Storch and his coworkers (55) obtained a value of 25 kcal./mole at long contact times corresponding to the Ruhrchemie process. 

Despite the fact that the Shell process operates at lower pressure and higher temperatures than the conventional processes, still higher n/iso ratios of the products formed are observed. Thus, in the hydroformylation of propylene an 88/12 ratio of n- over iso-product is obtained, whereas for comparison the distribution in the Ruhrchemie process is 80/20. This type of modified catalyst is not only a hydroformylation but also a hydrogenation catalyst. Thus, in the SheU process about 10-15 % of the olefin fed is lost through hydrogenation to the paraffin whereas the figures for the conventional 0X0 processes are only about 2-3 %. 

Fig. 13. Flowsheet of medium pressure synthesis, fixed-bed reactor (Lurgi-Ruhrchemie-Sasol) having process conditions for SASOL I of an alkaline, precipitated-iron catalyst, reduction degree 20—25% having a catalyst charge of 32—36 t, at 220—255°C and 2.48 MPa (360 psig) at a fresh feed rate of...

Good rhodium retention results were obtained after several recycles. However, optimized ligand/metal ratios and leaching and decomposition rates, which can result in the formation of inactive catalyst, are not known for these ligands and require testing in continuous mode. As a reference, in the Ruhrchemie-Rhone-Poulenc process, the losses of rhodium are <10 g Rh per kg n-butyraldehyde. 

Although rhodium recovery is efficient it is difficult to separate it from heavies that are formed in small amounts. Over time these heavies tend to result in some catalyst deactivation. One solution to this problem has been developed by Ruhrchemie/Rhone-Poulenc. In this process sulfonated triphenyl phosphine is used as the ligand, which imparts water solubility to the catalyst. The reaction is two-phase, a lower aqueous phase containing the catalyst and an upper organic phase. Fortunately the catalyst appears to sit at the interface enabling reaction to proceed efficiently. At the end of... 

An example of a large scale application of the aqueous biphasic concept is the Ruhrchemie/Rhone-Poulenc process for the hydroformylation of propylene to n-butanal (Eqn. (15)), which employs a water-soluble rhodium(I) complex of trisulphonated triphenylphosphine (tppts) as the catalyst (Cornils and Wiebus, 1996). 

Immobilization of catalysts is an important process design feature (see Chapter 9.9). A recent example of catalyst immobilization is the biphasic approach which seems superior to immobilization on solids, as successfully proven in the Ruhrchemie/Rhone Poulenc process for the hydro-formylation of olefins.286 Supported liquid phase catalysis was devised as a method for the immobilization of homogeneous catalysts on solids. When the liquid phase is water, a water-soluble catalyst may be physically bound to the solid. 

Cobalt carbonyls are the oldest catalysts for hydroformylation and they have been used in industry for many years. They are used either as unmodified carbonyls, or modified with alkylphosphines (Shell process). For propene hydroformylation, they have been replaced by rhodium (Union Carbide, Mitsubishi, Ruhrchemie-Rhone Poulenc). For higher alkenes, cobalt is still the catalyst of choice. Internal alkenes can be used as the substrate as cobalt has a propensity for causing isomerization under a pressure of CO and high preference for the formation of linear aldehydes. Recently a new process was introduced for the hydroformylation of ethene oxide using a cobalt catalyst modified with a diphosphine. In the following we will focus on relevant complexes that have been identified and recently reported reactions of interest. 

RCH/RP [Ruhrchemie/Rhone Poulenc] A variation of the 0X0 process in which the triphenyl phosphine (part of the Wilkinson catalyst) is sulfonated, in order to render the catalyst soluble in water for easier recovery. First commercialized in 1984 for the manufacture of butyraldehyde. 

Aqueous two-phase hydrogenation may be a method of choice for synthetic purposes when no incompatibility problems between water and the substrates, products, or catalyst arise. It has already been proven by the success of the Ruhrchemie-Rhone-Poulenc hydroformylation process, that the catalyst can be retained in the aqueous phase with very high efficiency, and that aqueous-organic biphasic processes using organometallic catalysts are suitable for indus-... 

The synthesis of aldehydes via hydroformylation of alkenes is an important industrial process used to produce in the region of 6 million tonnes a year of aldehydes. These compounds are used as intermediates in the manufacture of plasticizers, soaps, detergents and pharmaceutical products [7], While the majority of aldehydes prepared from alkene hydroformylation are done so in organic solvents, some research in 1975 showed that rhodium complexes with sulfonated phosphine ligands immobilized in water were able to hydroformylate propene with virtually complete retention of rhodium in the aqueous phase [8], Since catalyst loss is a major problem in the production of bulk chemicals of this nature, the process was scaled up, culminating in the Ruhrchemie-Rhone-Poulenc process for hydroformylation of propene, initially on a 120000 tonne per year scale [9], The development of this biphasic process represents one of the major transitions since the discovery of the hydroformylation reaction. The key transitions in this field include [10] ... 

In Chapter 8 we will discuss the hydroformylation of propene using rhodium catalysts. Rhodium is most suited for the hydroformylation of terminal alkenes, as we shall discuss later. In older plants cobalt is still used for the hydroformylation of propene, but the most economic route for propene hydroformylation is the Ruhrchemie/Rhone-Poulenc process using two-phase catalysis with rhodium catalysts. For higher alkenes, cobalt is still the preferred catalyst, although recently major improvements on rhodium (see Chapter 8) and palladium catalysts have been reported [3],... 

The basic solution in water containing NaCo(CO)4 is treated with sulphuric acid in the presence of syn-gas and HCo(CO)4 is regenerated. This can be extracted as is shown in the drawing from water into the substrate, alkene. The catalyst is returned to the reactor dissolved in the alkene. Compared to other schemes (BASF, Ruhrchemie) the elegant detail of the Kuhlmann process is... 

The tppts process has been commercialised by Ruhrchemie (now Celanese), after the initial work conducted by workers at Rhone-Poulenc, for the production of butanal from propene. Since 1995 Hoechst (now Celanese) also operates a hydroformylation plant for 1-butene. The partly isomerised, unconverted butenes are not recycled but sent to a reactor containing a cobalt catalyst. The two-phase process is not suited for higher alkenes because of the... 

Hoechst-Ruhrchemie (now Celanese) reported that no detectable losses of rhodium occur. We assume that propene is stripped from the aldehyde product and finally distillation of the aldehyde is conducted to separate the branched (8%) and linear product (92%). Note that the amounts of water lost in the aldehyde phase have to be replaced. Note also that by-products arising from aldol condensation, if any, are separated from the catalyst together with the product. These heavy ends end up in the bottom of the product distillation, which is advantageous, as the bottom can be sent to an incinerator. In processes such as the Shell process (Figure 7.6), the heavy end is a mixture of... 

A very elegant solution to solve this problem is the introduction of either a permanent or a temporary phase boundary between the molecular catalyst and the product phase. The basic principle of multiphase catalysis has already found implementation on an industrial scale in the Shell higher olefin process (SHOP) and the Ruhrchemie/Rhdne-Poulenc propene hydroformylation process. Over the years, the idea of phase-separable catalysis has inspired many chemists to design new families of ligands and to develop new separation... 

In 1975 Kuntz has described that the complexes formed from various rhodium-containing precursors and the sulfonated phosphines, TPPDS (2) or TPPTS (3) were active catalysts of hydroformylafion of propene and 1-hexene [15,33] in aqueous/organic biphasic systems with virtually complete retention of rhodium in the aqueous phase. The development of this fundamental discovery into a large scale industrial operation, known these days as the Ruhrchemie-Rhone Poulenc (RCH-RP) process for hydroformylation of propene, demanded intensive research efforts [21,28]. Tire final result of these is characterized by the data in Table 4.2 in comparison with cobalt- or rhodium-catalyzed processes taking place in homogeneous organic phases. 

---