Rubber modifiers

Rubber Modifiers. Derivatives of furan and tetrahydrofurfuryl alcohol are used in the polymerization of synthetic mbber to control stereoregularity and otherproperti.es (149,150). 

Fig. 3. Typical creep behavior for rubber-modified styrene polymers.

Rubber-Modified Copolymers. Acrylonitrile—butadiene—styrene polymers have become important commercial products since the mid-1950s. The development and properties of ABS polymers have been discussed in detail (76) (see Acrylonitrile polymers). ABS polymers, like HIPS, are two-phase systems in which the elastomer component is dispersed in the rigid SAN copolymer matrix. The electron photomicrographs in Figure 6 show the difference in morphology of mass vs emulsion ABS polymers. The differences in stmcture of the dispersed phases are primarily a result of differences in production processes, types of mbber used, and variation in mbber concentrations. 

I ew Rubber-Modified Styrene Copolymers. Rubber modification of styrene copolymers other than HIPS and ABS has been useful for specialty purposes. Transparency has been achieved with the use of methyl methacrylate as a comonomer styrene—methyl methacrylate copolymers have been successfully modified with mbber. Improved weatherability is achieved by modifying SAN copolymers with saturated, aging-resistant elastomers (88). 

R. Siebert, "Rubber-Modified Thermoset Resins," in C. K. Riew and J. K. GiUham, eds., ACS Advances in Chemistry Series 208, American Chemical Society, Washington, D.C., 1983, p. 179 W. D. Bascom and D. L. Hunston, "Rubber Toughened Plastic," Adv. Chem. Ser. No. 222, American Chemical Society, Washington, D.C., 1989. 

KESKKULA, H., Chapter entitled Rubber-modified Styrene Polymers in Polyblends and Composites (Ed. bruins, p. f.). Interscience, New York (1970)... 

Polyethylene is sometimes blended with ethylene-propylene rubber (see Chapter 11). In this application it is most commonly used as an additive to the rubber, which in turn is added to polypropylene to produce rubber-modified... 

Table 15.3 Comparison of properties of some rubber-modified polymers with polyimethyl methacrylate)...

Because of such desirable characteristics as low cost, good mouldability, excellent colour range, transparency, rigidity and low water absorption, polystyrene became rapidly developed. For many purposes, however, it was considered to be unacceptably brittle and this led to the development of the rubber-modified high-impact polystyrene (HIPS) and to the complex ABS, AMBS and... 

Elastomers, plastics, fabrics, wood and metals can be joined with themselves and with each other using nitrile rubber/epoxy resin blends cured with amines and/or acidic agents. Ethylene-propylene vulcanizates can also be joined using blends of carboxylated nitrile rubber, epoxy resin and a reactive metal filler (copper, nickel, cobalt). However, one of the largest areas of use of nitrile rubber modified epoxy systems is in the printed circuit board area [12]. 

In the late 1940s, the demand for styrene homopolymers (PS) and styrene-acrylonitrile copolymers (SAN) was drastically reduced due to their inherent brittleness. Thus, the interest was shifted to multiphase high-impact polystyrene (HIPS) and rubber-modified SAN (ABS). In principle, both HIPS and ABS can be manufactured by either bulk or emulsion techniques. However, in actual practice, HIPS is made only by the bulk process, whereas ABS is produced by both methods [132,133]. 

Acrylated rubber Modified chlorinated rubber Bituminous Vinyl tar... 

Thermoplastics may themselves be considered in four sub-classes (a) amorphous thermoplastics, (b) rubber-modified amorphous thermoplastics, (c) plasticised amorphous thermoplastics and (d) crystalline thermoplastics. 

Rubber-modified amorphous polymers The brittleness of amorphous polymers has been a hindrance in their commercial development. Fortunately, for reasons still not fully understood, the addition of rubbery polymers as dispersed droplets, or sometimes in a network form, into the glassy polymer can often lead to substantial increases in impact strength, albeit usually at... 

Styrene maleic anhydride SMA is a copolymer made with or without rubber modifiers. They are sometimes alloyed with ABS and offer good heat resistance, high impact strength and gloss but with little appreciable improvement in weatherability or chemical resistance over other styrene based plastics. 

Rotational casting elastomers, 204 Rubber, urethane, 201 Rubberlike polymers, 18 Rubber-modified blends, 149 Rynite, 21... 

Table 17 provides a list of various polysiloxane-poly(aryl ether) copolymers investigated. Depending on the type, nature and the level of the hard blocks incorporated, physical, thermal and mechanical properties of these materials can be varied over a very wide range from that of thermoplastic elastomers to rubber modified engineering thermoplastics. Resultant copolymers are processable by solution techniques and in some cases by melt processing 22,244). 

---