Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Rotating table

Figure 3 gives a view of a bucket on the rotation table in front of the shutter of the image intensifier. [Pg.454]

An important variation of this filter is based on replacing the rigid outer waU necessary for containing the feed and the cake on the rotating table by an endless mbber belt. The belt is held under tension and rotates with the table. It is in contact with the table rim except for the sector where the discharge screw is positioned, and where the belt is deflected away from the table to aUow the soHds to be pushed off the table. The cloth can also be washed in this section by high pressure water sprays. This filter, recendy developed in Belgium, is avaUable in sizes up to 250 m, operated at speeds of 2 minutes per revolution, and cake thicknesses up to 200 mm. [Pg.395]

A series of fixed trapezoidal cells that form a rotating table and each connected to a stationary valve in the center of the filter. The cell is designed with steep sloped bottom for fast evacuation of the filtrate. [Pg.231]

Modem apparatus are equipped with a rotating table to accommodate the TLC plate above the base of the reaction chamber This means that microwaves can penetrate the TLC plate from below through the glass plate or plastic film Aluminium foil backings are not suitable They reflect the radiation and high potentials are built up between the aluminium foil and the wall of the reaction chamber, these result in electrical discharges... [Pg.98]

Close the blind rams, open the rotating head to release the 3 in. stripper rubber, pull the rotating table bushings and raise the last joint of drill collar, remove the bit, and lay this Joint down (remove the 3in. stripper rubber from this drill collar Joint for later use). [Pg.851]

The discharge rate of solid particles is usually controlled by the size of the orifice or the aperture at the base of the hopper, though sometimes screw feeders or rotating table feeders may be incorporated to encourage an even flowrate. [Pg.27]

The rate of feed of solids may be controlled using screw feeders, rotating tables or vibrating feeders, such as magnetically vibrated troughs. Volumetric rates may be controlled by regulating the speeds of rotation of star feeders or rotary vaned valves. [Pg.29]

Fro. 1. Suite of three rotating-table glove-boxes. [Pg.204]

The nmr data for this type of motion are direct and the motion clearly involves rotation about bonds in the millisecond time scale range. However. less direct evidence for motion comes from other techniques such as fluorescence depolarization, 02 diffusion, hydrogen exchange kinetics, and nmr relaxation times (see Ref. 4). The extent of this motion is not yet easy to define, but this evidence points to motion in the nanosecond time scale range. It is tempting to see the motion in this time scale as bond oscillations rather than rotations. To put it in a different way, on this time scale the side chains have some freedom to move with respect to each other but not normally to undergo substantial bond rotation. Table IV summarizes some references for motion of different types. Additionally, nmr relaxation studies suggest that the backbone or main chain of a protein is more restricted than that of the side chains. [Pg.74]

In Germany a machine of the Niepmann type has been adapted for cartridging dynamite [7]. A schematic view of its operation is shown in Fig. 179. The explosive supplied through funnel (/) is pushed out through worm (2) into conduits (4) and (5), from which it is ejected by pistons (5). The empty paper cases are fed by conveyer ( ) into slots on the rotating table (7). When the cases reach position (8), a charge of plastic material, extruded from the orifice (6), is slipped into them. Further rotation severs the rods of dynamite while the cases, already filled, are passed to... [Pg.517]

Pseudocercosperella herpotrichoides in a trial of two different seven year rotations (Table 3.5) was interpreted by Baeumer (1992) as a response to the replacement of sugar beet and oats by grass-clover, the interruption of the infection chain from wheat to wheat, and the decrease of the cereal proportion from 57% to 43%. Although these results were not obtained in organic farming systems, they are of direct relevance. [Pg.61]

As expected, the largest portion of the cycle time is the cooling of the blow molded container in the mold cavity. Most machines work with multiple molds in order to increase production. Rotary molds are often used in conjunction with vertical or horizontal rotating tables (Fig. 3.59 [14]). [Pg.154]

Figure 3.59 Schematic of an extrusion blow molder with a rotating table. Figure 3.59 Schematic of an extrusion blow molder with a rotating table.
Prepolymers heated in a microwave oven, even using a rotating table, will have uneven temperatures, and the material needs to be mixed well before taking a temperature reading. [Pg.164]

Different extrusion profile processes can be used such as a robotic profile. A robot delivers the hot melt over or around a substrate. This robotic extrusion process can uses a flexible, heated, high-pressure hose that is connected to the extruder s die exit. The hot melt travels through the hose. At the end of the hose is a nozzle the tip of this nozzle is, in effect the actual profile die. A computer-regulated multiaxis robot controls the positioning of the profile nozzle die. The nozzle/die is guided by the robot to deposit the profile s hot melt on, as an example, a substrate that is on a multi-station rotating table supporting other substrates to be covered. [Pg.257]

The basic unit of any tablet press is tooling consisting of two punches and a die, called a station. The upper and lower punches come together in the die that contains the tablet formulation. Principally, two different types of machines are used, the eccentric and the rotary press. The eccentric press produces about 50-130 tablets per minute. The rotary press has a multiplicity of stations arranged on a rotating table with the dies. A few or many thousands of tablets can be produced per minute. There are numerous models of presses, manufactured by a number of companies, ranging in size, speed, and capacity. [Pg.978]

Heat-stable colors are added at this point as cubes or paste. The colored candy base is transferred to a cold stainless-steel cooling plate for the mixing operation. Mixing can be manual or mechanical, using a series of plows and rollers, or a mixer consisting of two arms, a plunger, and a slowly rotating table top. [Pg.2233]

Rotating table in tabletting machines carrying the tooling. [Pg.18]

German Patent 158 023, press with rotating table and punches... [Pg.225]


See other pages where Rotating table is mentioned: [Pg.308]    [Pg.383]    [Pg.436]    [Pg.142]    [Pg.80]    [Pg.10]    [Pg.109]    [Pg.116]    [Pg.129]    [Pg.436]    [Pg.204]    [Pg.58]    [Pg.308]    [Pg.383]    [Pg.86]    [Pg.391]    [Pg.201]    [Pg.274]    [Pg.334]    [Pg.13]    [Pg.16]    [Pg.92]    [Pg.211]    [Pg.273]    [Pg.142]    [Pg.472]    [Pg.425]    [Pg.562]    [Pg.128]    [Pg.225]   


SEARCH



Rotating Table Fiber

Rotational barriers table

Rotational collision numbers, table

Specific rotation table

Table, circular rotating sample

© 2024 chempedia.info