Reverse osmosis rejection

Extraction of Surfactant. The influence of surfactant on the physical properties of the fiber require its removal prior to the establishment of the reverse osmosis rejection membrane. Surfactant is removed in a pressure extraction apparatus by the recirculation of hot aqueous alcohol. Surfactant is removed to concentrations less than 2% on the weight of dry fiber. 

Species Nanofiltration Rejection (%) Reverse Osmosis Rejection (%)... 

Finding 4-1. The documentation for secondary waste streams made available to the committee failed to identify reverse osmosis rejectate brine, supercritical water oxidation (SCWO) filtrate solid waste, SCWO titanium tank hners, venturi scrubber particulate filters, or filters from the ener-... 

It should be expected that calculated values of 6jjp correlate better with equilibrium properties of the membranes in aqueous solution than with transport properties. Che of the few such equilibrium measurements that have been published is by Anderson et al (.2J). Their measured partition coefficients (K), diffusion coefficients (D), and reverse osmosis rejection (R) of the organic solutes are shown in Table III for cellulose acetate membranes. Their data for cellulose acetate butyrate was similar and is not shown here. Aqueous solutions of the organic solutes, usually at concentrations of about 10 g 1 , were used in the measurement of partition coefficients by UV absorption. In Table III,... 

Reverse osmosis is a high-pressure membrane separation process (20 to 100 bar) which can be used to reject dissolved inorganic salt or heavy metals. The concentrated waste material produced by membrane process should be recycled if possible but might require further treatment or disposal. 

In other areas, POD has been used to improve the wear resistance of a mbber latex binder by incorporation of 25% of Oksalon fibers. Heat-resistant laminate films, made by coating a polyester film with POD, have been used as electrical insulators and show good resistance to abrasion and are capable of 126% elongation. In some instances, thin sheets of PODs have been used as mold release agents. For this appHcation a resin is placed between the two sheets of POD, which is then pressed in a mold, and the sheets simply peel off from the object and mold after the resin has cured. POD-based membranes exhibit salt rejection properties and hence find potential as reverse osmosis membranes in the purification of seawater. PODs have also been used in the manufacturing of electrophotographic plates as binders between the toner and plate. These improved binders produce sharper images than were possible before. 

Interfdci l Composite Membra.nes, A method of making asymmetric membranes involving interfacial polymerization was developed in the 1960s. This technique was used to produce reverse osmosis membranes with dramatically improved salt rejections and water fluxes compared to those prepared by the Loeb-Sourirajan process (28). In the interfacial polymerization method, an aqueous solution of a reactive prepolymer, such as polyamine, is first deposited in the pores of a microporous support membrane, typically a polysulfone ultrafUtration membrane. The amine-loaded support is then immersed in a water-immiscible solvent solution containing a reactant, for example, a diacid chloride in hexane. The amine and acid chloride then react at the interface of the two solutions to form a densely cross-linked, extremely thin membrane layer. This preparation method is shown schematically in Figure 15. The first membrane made was based on polyethylenimine cross-linked with toluene-2,4-diisocyanate (28). The process was later refined at FilmTec Corporation (29,30) and at UOP (31) in the United States, and at Nitto (32) in Japan. 

The first reverse osmosis modules made from cellulose diacetate had a salt rejection of approximately 97—98%. This was enough to produce potable water (ie, water containing less than 500 ppm salt) from brackish water sources, but was not enough to desalinate seawater efficiently. In the 1970s, interfacial composite membranes with salt rejections greater than 99.5% were developed, making seawater desalination possible (29,30) a number of large plants are in operation worldwide. 

Some data iEustrating the effect of pressure on the water and salt fluxes and the salt rejection of a good quaUty reverse osmosis membrane are shown ia Figure 34 (76). 

Memhra.nes. Liquid separation via membranes, ie, reverse osmosis (qv), is used in production of pure water from seawater. The chief limit to broader use of reverse osmosis is the high pressure required as the concentration of reject rises. 

The pressure difference between the high and low pressure sides of the membrane is denoted as AP the osmotic pressure difference across the membrane is defined as Att the net driving force for water transport across the membrane is AP — (tAtt, where O is the Staverman reflection coefficient and a = 1 means 100% solute rejection. The standardized terminology recommended for use to describe pressure-driven membrane processes, including that for reverse osmosis, has been reviewed (24). 

The individual membrane filtration processes are defined chiefly by pore size although there is some overlap. The smallest membrane pore size is used in reverse osmosis (0.0005—0.002 microns), followed by nanofiltration (0.001—0.01 microns), ultrafHtration (0.002—0.1 microns), and microfiltration (0.1—1.0 microns). Electro dialysis uses electric current to transport ionic species across a membrane. Micro- and ultrafHtration rely on pore size for material separation, reverse osmosis on pore size and diffusion, and electro dialysis on diffusion. Separation efficiency does not reach 100% for any of these membrane processes. For example, when used to desalinate—soften water for industrial processes, the concentrated salt stream (reject) from reverse osmosis can be 20% of the total flow. These concentrated, yet stiH dilute streams, may require additional treatment or special disposal methods. 

The pressure to be used for reverse osmosis depends on the salinity of the feedwater, the type of membrane, and the desired product purity. It ranges from about 1.5 MPa for low feed concentrations or high flux membranes, through 2.5—4 MPa for brackish waters, and to 6—8.4 MPa for seawater desalination. In desalination of brackish or sea water, typical product water fluxes through spiral-wound membranes are about 600—800 kg/m /d at a recovery ratio RR of 15% and an average salt rejection of 99.5%, where... 

Common membrane processes include ultrafiltration (UF), reverse osmosis (RO), electro dialysis (ED), and electro dialysis reversal (EDR). These processes (with the exception of UF) remove most ions RO and UF systems also provide efficient removal of nonionized organics and particulates. Because UF membrane porosity is too large for ion rejection, the UF process is used to remove contaminants, such as oil and grease, and suspended soHds. 

Retention Rejection and Reflection Retention and rejection are used almost interchangeably. A third term, reflection, includes a measure of solute-solvent coupling, and is the term used in irreversible thermodynamic descriptions of membrane separations. It is important in only a few practical cases. Rejection is the term of trade in reverse osmosis (RO) and NF, and retention is usually used in UF and MF. 

---