Render Once

The Suntmary View at the hottom of the Explorer window displays the relevant video properties. 

From the Save as type list, select Video for Windows (. avi). 

Video that is destined for playback on your computer is much more complex to render. This is because this type of video needs to be compressed, reducing the file size and making video download times more realistic. Compression occurs in a number of different ways and always 

The other way video is compressed is interframe or between fiames. In this case, there can be a similar process of comparing blocks of color in a number of different frames and saving this information to a single piece of information, instead of many pieces for each frame. This is why video with little motion (little change between frames) compresses much better. Of course, this is a great simplification to this decidedly high-tech process, but even a basic understanding will help you to make better choices about video for the Internet. 

ACID can save video in four basic formats . avi,. mov,. rm, and. wmv. These formats do not define individual codecs and should not be confused with the actual codecs that are used for compression. In other words, it is not possible to say that. mov files are better than. wmv files, since each may use different underlying codecs or possibly even very similar codecs. There are situations where you might want to use one or the other, and the following sections should guide you a bit in making a decision. 

---

Drop 1 g. of sodium into 10 ml. of ethyl alcohol in a small flask provided with a small water condenser heat the mixture until all the sodium has dissolved. Cool, and add 1 g. of the ester and 0-5 ml. of water. Frequently the sodium salt of the acid will be deposited either at once or after boiling for a few minutes. If this occurs, filter oflF the solid at once, wash it with a little absolute ethyl alcohol (or absolute methylated spirit), and convert it into the p-bromophenacyl ester, p-nitro-benzyl ester or S-benzyl-tso-thiuronium salt (for experimental details, see Section 111,85). If no solid separates, continue the boiling for 30-60 minutes, boil oflF the alcohol, allow to cool, render the product just neutral to phenolphthalein with dilute sulphuric or hydrochloric acid, convert the sodium salt present in solution into a crystalline derivative (Section 111,85), and determine its melting point. 

Prepare a solution of 41 g. of anhydrous palladium chloride (1) in 10 ml. of concentrated hydrochloric acid and 25 ml. of water (as in A). Add all at once 60 ml. of 6iV-sulphuric acid to a rapidly stirred, hot (80°) solution of 63 1 g. of A.R. crystallised barium hydroxide in 600 ml. of water contained in a 2-htre beaker. Add more 6iV-sulphuric acid to render the suspension just acid to htmus (5). Introduce the palladium chloride solution and 4 ml. of 37 per cent, formaldehyde solution into the hot mechanically stirred suspension of barium sulphate. Render the suspension slightly alkaline with 30 per cent, sodium hydroxide solution, continue the stirring for 5 minutes longer, and allow the catalyst to settle. Decant the clear supernatant hquid, replace it by water and resuspend the catalyst. Wash the catalyst by decantation 8-10 times and then collect it on a medium - porosity sintered glass funnel, wash it with five 25 ml. portions of water and suck as dry as possible. Dry the funnel and contents at 80°, powder the catalyst (48 g.), and store it in a tightly stoppered bottle. 

Once the job is completed, the UniChem GUI can be used to visualize results. It can be used to visualize common three-dimensional properties, such as electron density, orbital densities, electrostatic potentials, and spin density. It supports both the visualization of three-dimensional surfaces and colorized or contoured two-dimensional planes. There is a lot of control over colors, rendering quality, and the like. The final image can be printed or saved in several file formats. 

Unlike products, nonconforming services are usually rendered unavailable for use by notices such as Out of Order or by announcements such as Normal service will be resumed as soon as possible . Products are often capable of operation with nonconformities whereas services tend to be withdrawn once the nonconformity has been detected, however trivial the fault. 

For the identification of limonene, one of the most useful compounds is the crystalline tetrabromide, Cj(,HjgBr. This body is best prepared as follows the fraction of the oil containing much limonene is mixed with four times its volume of glacial acetic acid, and the mixture cooled in ice. Bromine is then added, drop by drop, so long as it becomes decolorised at once. The mixture is then allowed to stand until crystals separate. These are filtered off, pressed between porous paper, and recrystallised from acetic ether. Limonene tetrabromide melts at 104 5° and is optically active, its specific rotation being + 73 3°. The inactive, or dipeutene, tetrabromide melts at 124° to 125°. In the preparation of the tetrabromide traces of moisture are advisable, as the use of absolutely anhydrous material renders the compound very diflftcult to crystallise. 

The mixture is taken up with water and the base is extracted from the toluene with dilute hydrochloric acid. The hydrochloric solution is rendered alkaline with caustic soda, the base is separated with ether, dried, and after distillation of the ether fractionated in vacuo, BP at 0.05 mm Hg, 150° to 153°C. The basic ether is then dissolved in dry ether, and ether saturated with dry hydrogen chloride is added dropwise with stirring. An excess of hydrogen chloride must be avoided as it may produce decomposition to the corresponding diphenyl ethylene. The ether-moist hydrochloride is preferably dried at once in vacuo and subsequently reprecipitated from acetone-ether and then again dried in vacuo over phosphorus pentoxide. Hydrochloride, MP 12B°C. 

The proof of protection is more difficult to establish in this case for two reasons. First, the object is to restore passivity to the rebar and not to render it virtually immune to corrosion. Second, it is difficult to measure the true electrode potential of rebars under these conditions. This is because the cathodic-protection current flowing through the concrete produces a voltage error in the measurements made (see below). For this reason it has been found convenient to use a potential decay technique to assess protection rather than a direct potential measurement. Thus a 100 mV decay of polarisation in 4 h once current has been interrupted has been adopted as the criterion for adequate protection. It will be seen that this proposal does not differ substantially from the decay criterion included in Table 10.3 and recommended by NACE for assessing the full protection of steel in other environments. Of course, in this case the cathodic polarisation is intended to inhibit pit growth and restore passivity, not to establish effective immunity. 

---