Reflectance Raman spectroscopy

Leverette, C.L. and Dluhy, R.A. (2000) A novel fiber-optic interface for unenhanced external reflection Raman spectroscopy of supported monolayers. Langmuir, 16, 3977-3983. 

Ionic liquids at the gas-liquid and solid-liquid interface have been extensively studied by a variety of surface analytical techniques. The most prominent technique for surface orientational analysis proves to be SFG. Other vibrational spectroscopic and surface-sensitive techniques such as surface-enhanced Raman spectroscopy (SERS) and total internal reflection Raman spectroscopy (TIR Raman) have been employed for studying surface processes these techniques, however, have not been applied yet specifically for the study of ionic hquids. 

Iwamoto R., Miya M., Ohta K., Mima S. Total internal reflection Raman spectroscopy, J. Chem. Phys. 1981,74,4780-4790. 

Vibrational Spectroscopy. Infrared absorption spectra may be obtained using convention IR or FTIR instrumentation the catalyst may be present as a compressed disk, allowing transmission spectroscopy. If the surface area is high, there can be enough chemisorbed species for their spectra to be recorded. This approach is widely used to follow actual catalyzed reactions see, for example. Refs. 26 (metal oxide catalysts) and 27 (zeolitic catalysts). Diffuse reflectance infrared reflection spectroscopy (DRIFT S) may be used on films [e.g.. Ref. 28—Si02 films on Mo(llO)]. Laser Raman spectroscopy (e.g.. Refs. 29, 30) and infrared emission spectroscopy may give greater detail [31]. 

The deterrnination of surface temperature and temperature patterns can be made noninvasively using infrared pyrometers (91) or infrared cameras (92) (see Infrared technology and raman spectroscopy). Such cameras have been bulky and expensive. A practical portable camera has become available for monitoring surface temperatures (93). An appropriately designed window, transparent to infrared radiation but reflecting microwaves, as well as appropriate optics, is needed for this measurement to be carried out during heating (see Temperature measurement). 

Several properties of the filler are important to the compounder (279). Properties that are frequentiy reported by fumed sihca manufacturers include the acidity of the filler, nitrogen adsorption, oil absorption, and particle size distribution (280,281). The adsorption techniques provide a measure of the surface area of the filler, whereas oil absorption is an indication of the stmcture of the filler (282). Measurement of the sdanol concentration is critical, and some techniques that are commonly used in the industry to estimate this parameter are the methyl red absorption and methanol wettabihty (273,274,277) tests. Other techniques include various spectroscopies, such as diffuse reflectance infrared spectroscopy (drift), inverse gas chromatography (igc), photoacoustic ir, nmr, Raman, and surface forces apparatus (277,283—290). 

Laser stimulation of a silver surface results in a reflected signal over a million times stronger than that of other metals. Called laser-enhanced Raman spectroscopy, this procedure is useful in catalysis. The large neutron cross section of silver (see Fig. 2), makes this element useful as a thermal neutron flux monitor for reactor surveillance programs (see Nuclearreactors). 

Raman spectroscopy has provided information on catalytically active transition metal oxide species (e. g. V, Nb, Cr, Mo, W, and Re) present on the surface of different oxide supports (e.g. alumina, titania, zirconia, niobia, and silica). The structures of the surface metal oxide species were reflected in the terminal M=0 and bridging M-O-M vibrations. The location of the surface metal oxide species on the oxide supports was determined by monitoring the specific surface hydroxyls of the support that were being titrated. The surface coverage of the metal oxide species on the oxide supports could be quantitatively obtained, because at monolayer coverage all the reactive surface hydroxyls were titrated and additional metal oxide resulted in the formation of crystalline metal oxide particles. The nature of surface Lewis and Bronsted acid sites in supported metal oxide catalysts has been determined by adsorbing probe mole-... 

The species S3 (absorbing at 420 nm) and S4 (absorbing at 530 nm) have been detected by reflection spectra in the condensate but the formation of S4 is unexplained [16]. S3 and SO2 have also been observed by Raman spectroscopy in such samples [15] (the expected S4 Raman line at 678 cm was probably obscured by the SS stretching mode of S2O at 673 cm but a shoulder at the high-frequency side of the S2O line indicates that some S4 may have been present). While the reddish colors turn yellow on warming at about -120 °C, the sulfur radicals could be observed by ESR spectroscopy up to 0 °C [10]. If the condensation of S2O gas is performed very slowly at -196 °C the condensate is almost colorless and turns red only if the temperature is allowed to increase slowly. Hence, it has been suspected that S2O is actually colorless like SO2. 

Of special Interest as O2 reduction electrocatalysts are the transition metal macrocycles In the form of layers adsorptlvely attached, chemically bonded or simply physically deposited on an electrode substrate Some of these complexes catalyze the 4-electron reduction of O2 to H2O or 0H while others catalyze principally the 2-electron reduction to the peroxide and/or the peroxide elimination reactions. Various situ spectroscopic techniques have been used to examine the state of these transition metal macrocycle layers on carbon, graphite and metal substrates under various electrochemical conditions. These techniques have Included (a) visible reflectance spectroscopy (b) laser Raman spectroscopy, utilizing surface enhanced Raman scattering and resonant Raman and (c) Mossbauer spectroscopy. This paper will focus on principally the cobalt and Iron phthalocyanlnes and porphyrins. 

With recent developments in analytical instrumentation these criteria are being increasingly fulfilled by physicochemical spectroscopic approaches, often referred to as whole-organism fingerprinting methods.910 Such methods involve the concurrent measurement of large numbers of spectral characters that together reflect the overall cell composition. Examples of the most popular methods used in the 20th century include pyrolysis mass spectrometry (PyMS),11,12 Fourier transform-infrared spectrometry (FT-IR), and UV resonance Raman spectroscopy.16,17 The PyMS technique... 

In recent years,3 4 however, there has been renewed interest in the study of the electrode/solution interface due in part to the development of new spectroscopic techniques such as surface-enhanced Raman spectroscopy,5-7 electrochemically modulated infrared reflectance spectroscopy and related techniques,8,9 second-harmonic generation,10-12 and others which give information about the identity and orientation of molecular species in the interfacial... 

---