Reference electrodes performance

Reference electrode performance also includes the response kinetics. For example,... 

There are two good methods for testing the reference electrode performance. One test is based on comparing the questionable reference to the other reference known to have good performance. Since one reference electrode potential is offset by the other dectrode potential, the test is often referred to as bucking. This... 

Other problems occur in the measurement of pH in unbuffered, low ionic strength media such as wet deposition (acid rain) and natural freshwaters (see Airpollution Groundwatermonitoring) (13). In these cases, studies have demonstrated that the principal sources of the measurement errors are associated with the performance of the reference electrode Hquid junction, changes in the sample pH during storage, and the nature of the standards used in caHbration. Considerable care must be exercised in all aspects of the measurement process to assure the quaHty of the pH values on these types of samples. 

The titrations so far discussed in this chapter have been concerned with the use of a reference electrode (usually S.C.E.), in conjunction with a polarised electrode (dropping mercury electrode or rotating platinum micro-electrode). Titrations may also be performed in a uniformly stirred solution by using two small but similar platinum electrodes to which a small e.m.f. (1-100 millivolts) is applied the end point is usually shown by either the disappearance or the appearance of a current flowing between the two electrodes. For the method to be applicable the only requirement is that a reversible oxidation-reduction system be present either before or after the end point. 

While in previous ab initio smdies the reconstructed surface was mostly simulated as Au(lll), Feng et al. [2005] have recently performed periodic density functional theory (DFT) calculations on a realistic system in which they used a (5 x 1) unit cell and added an additional atom to the first surface layer. In their calculations, the electrode potential was included by charging the slab and placing a reference electrode (with the counter charge) in the middle of the vacuum region. From the surface free energy curves, which were evaluated on the basis of experimentally measured capacities, they concluded that there is no necessity for specific ion adsorption [Bohnen and Kolb, 1998] and that the positive surface charge alone would be sufficient to lift the reconstmction. 

Cyclic voltammetry was performed on precursor polymer thin films cast on platinum electrodes in order to assess the possibility of electrochemical redox elimination and consequently as an alternative means of monitoring the process. All electrochemical experiments were performed in a three-electrode, single-compartment cell using a double junction Ag/Ag+(AgN03) reference electrode in 0.1M... 

Rabenstein and Yamashita [52] determined penicillamine and its symmetrical and mixed disulfides by HPLC in biological fluids. Plasma and urine were deproteinized with trichloroacetic acid, and HPLC was performed on a column (25 cm x 4.6 mm) or Biophase ODS (5 pm) with a mobile phase comprising 0.1 M phosphate buffer (pH 3) and 0.34 mM Na octylsulfate at 1 mL/min. Detection was with a dual Hg-Au amalgam electrode versus a Ag-AgCl reference electrode. (z>)-penicillamine and homocysteine were determined at the downstream electrode at +0.15 V, and homocystine, penicillamine-homocysteine, and penicillamine disulfides were first reduced... 

The first STM experiments were performed under UHV conditions, and so the bias potential was simply applied as a difference across the tip and sample. However, introducing an electrolyte above the sample brought with it some particular problems. It is no longer sufficient simply to apply a bias voltage equal to the potential difference between tip and sample as this means that the potentials of the tip and sample are undefined with respect to any fixed reference, a wholly undesirable situation. Consequently, modern electrochemical STM systems operate under bipotentiostatic control with the tip and sample controlled and monitored independently with respect to the reference electrode. The bias potential is then still given by (Fs — FT), but VT and Fs are now potentials with respect to the reference electrode. 

An inner filling solution and internal reference electrode are used in macro ISEs due to a very good stability of the potential at the inner membrane-solution interface in such a setup (see Fig. 4.4). However, the presence of a solution inside a sensor could be a serious limitation for development of microelectrodes and may be undesired for a variety of other reasons, including ionic fluxes in the membrane and limited temperature range of sensor operation. There are several requirements for such an inner contact. First of all, a reversible change of electricity carriers ions-electrons must take place at the membrane-substrate interface. The potential of the electrochemical reaction, ensuring this transfer, has to be constant, stable, and must not depend on the sample composition. At last, the substrate must not influence the membrane analytical performance. 

Fig. 3. Diagrams of electrochemical cells used in flow systems for thin film deposition by EC-ALE. A) First small thin layer flow cell (modeled after electrochemical liquid chromatography detectors). A gasket defined the area where the deposition was performed, and solutions were pumped in and out though the top plate. Reproduced by permission from ref. [ 110]. B) H-cell design where the samples were suspended in the solutions, and solutions were filled and drained from below. Reproduced by permission from ref. [111]. C) Larger thin layer flow cell. This is very similar to that shown in 3A, except that the deposition area is larger and laminar flow is easier to develop because of the solution inlet and outlet designs. In addition, the opposite wall of the cell is a piece of ITO, used as the auxiliary electrode. It is transparent so the deposit can be monitored visually, and it provides an excellent current distribution. The reference electrode is incorporated right in the cell, as well. Adapted from ref. [113],...

The cyclic voltammograms of these systems display quasi-reversible behavior, with AEv/v being increased because of slow electrochemical kinetics. Standard electrochemical rate constants, ( s,h)obs> were obtained from the cyclic voltammograms by matching them with digital simulations. This approach enabled the effects of IR drop (the spatial dependence of potential due to current flow through a resistive solution) to be included in the digital simulation by use of measured solution resistances. These experiments were performed with a non-isothermal cell, in which the reference electrode is maintained at a constant temperature... 

Electrochemical Equipment. Electrochemical experiments were performed using either a PAR Model 175 universal programmer and a PAR Model 363 potentiostat/galvanostat, or a Pine Instruments RDE-4 bipotentiostat, coupled with a Kipp and Zonen BD 91 X-y-y recorder. The current-time response for the chronoamperometry experiments was recorded with a Nicolet 4094 digital oscilloscope. All potentials were measured vs. a Ag/10"2 M Ag+ reference electrode. 

In Nebraska, state regulations require that the chemical makeup of animal feed sold in the state be accurately reflected on the labels found on the feed bags. The Nebraska State Agriculture Laboratory is charged with the task of performing the analytical laboratory work required. An example is salt (sodium chloride) content. The method used to analyze the feed for sodium chloride involves a potentio-metric titration. A chloride ion-selective electrode in combination with a saturated calomel reference electrode is used. After dissolving the feed sample, the chloride is titrated with a silver nitrate standard solution. The reaction involves the formation of the insoluble precipitate silver chloride. The electrode monitors the decrease in the chloride concentration as the titration proceeds, ultimately detecting the end point (when the chloride ion concentration is zero). 

For cases directly comparable to the cyclization originating from (27) above, the yields of the product were not as high. However, a related reaction used in the synthesis of an 11-substituted dibenzo[a,d]-cycloheptenimine derivative was very successful as shown in Scheme 11 (Eq. 2) [32]. In this reaction, a controlled potential electrolysis of (33) led to the formation of the tetracyclic (34) in an 85% isolated yield. The reaction was performed on a 1 g scale using an undivided cell, a graphite felt anode, a stainless steel cathode, a saturated calomel reference electrode, and a 1% NaBF4 in 70 30 THF/water electrolyte solution. The electrolysis was scaled up further with the use of a flow cell. In this experiment, 200 g of (33) were oxidized in order to afford a 75% isolated yield of (34). 

In this present book, we will look at the analytical use of two fundamentally different types of electrochemical technique, namely potentiometry and amper-ometry. The distinctions between the two are outlined in some detail in Chapter 2. For now, we will anticipate and say that a potentiometric technique determines the potential of electrochemical cells - usually at zero current. The potential of the electrode of interest responds (with respect to a standard reference electrode) to changes in the concentration of the species under study. The most common potentiometric methods used by the analyst employ voltmeters, potentiometers or pH meters. Such measurements are generally relatively cheap to perform, but can be slow and tedious unless automated. 

We will now look at the effects of Ej on thermodynamic calculations, and then decide on the various methods that can be used to minimize them. One of the most common reasons for performing a calculation with an electrochemical cell is to determine the concentration or activity of an ion. In order to carry out such a calculation, we would first construct a cell, and then, knowing the potential of the reference electrode, we would determine the half-cell potential, i.e. the electrode potential E of interest, and then apply the Nemst equation. 

---