Reactor feed

Table 2.2 gives the compositions of the reactor feed and effluent streams. Calculate the conversion, selectivity, and reactor yield with respect to (a) the toluene feed and (b) the hydrogen feed. 

TABLE 2.2 Reactor Feed and Effluent streams in Example 2.3... 

Adiabatic operation. If adiabatic operation leads to an acceptable temperature rise for exothermic reactors or an acceptable fall for endothermic reactors, then this is the option normally chosen. If this is the case, then the feed stream to the reactor requires heating and the efiluent stream requires cooling. The heat integration characteristics are thus a cold stream (the reactor feed) and a hot stream (the reactor efiluent). The heat of reaction appears as elevated temperature of the efiluent stream in the case of exothermic reaction or reduced temperature in the case of endothermic reaction. 

Heat carriers. If adiabatic operation produces an unacceptable rise or fall in temperature, then the option discussed in Chap. 2 is to introduce a heat carrier. The operation is still adiabatic, but an inert material is introduced with the reactor feed as a heat carrier. The heat integration characteristics are as before. The reactor feed is a cold stream and the reactor efiluent a hot stream. The heat carrier serves to increase the heat capacity fiow rate of both streams. 

In addition to the indirect cooling/heating within the reactor, the reactor feed is an additional cold stream and the reactor product an additional hot stream. 

The appropriate placement of reactors, as far as heat integration is concerned, is that exothermic reactors should be integrated above the pinch and endothermic reactors below the pinch. Care should be taken when reactor feeds are preheated by heat of reaction within the reactor for exothermic reactions. This can constitute cross-pinch heat transfer. The feeds should be preheated to pinch temperature by heat recovery before being fed to the reactor. 

Most of the world s commercial formaldehyde is manufactured from methanol and air either by a process using a silver catalyst or one using a metal oxide catalyst. Reactor feed to the former is on the methanol-rich side of a flammable mixture and virtually complete reaction of oxygen is obtained conversely, feed to the metal oxide catalyst is lean in methanol and almost complete conversion of methanol is achieved. 

LDPE, also known as high pressure polyethylene, is produced at pressures ranging from 82—276 MPa (800—2725 atm). Operating at 132—332°C, it may be produced by either a tubular or a stirred autoclave reactor. Reaction is sustained by continuously injecting free-radical initiators, such as peroxides, oxygen, or a combination of both, to the reactor feed. 

Many units have waste heat recovery systems that generate low pressure steam from reaction heat. Such steam is often employed to drive adsorption refrigeration units to cool the reactor feed stream and to increase polymer conversion per pass, an energy-saving process that reduces the demand for electrical power. 

The conversion of fatty alcohols is approximately 99%. The reaction product is then condensed and sent to a distillation column to remove water and high boilers. Typically, a-olefin carbon-number distribution is controlled by the alcohol composition of the reactor feed. The process is currentiy used to produce a-olefins from fatty alcohols. A typical product composition is at <5%, at 50—70%, C g at 30—50%, C2Q at <2%,... 

A process for the production of DPA from phenol and ammonia has been reported (25). Typically, the reaction is carried out continuously ia a fixed-bed reactor usiag an acidic alumiaa catalyst at 300°C—420°C. The first product formed is aniline which is subsequently converted to DPA. Consequently, the reaction can be carried out to simultaneously produce DPA and aniline, ia any desired ratio, simply by varyiag the molar ratios of phenol (and aniline) ia the reactor feed stream. 

Oxychlorination reactor feed purity can also contribute to by-product formation, although the problem usually is only with low levels of acetylene which are normally present in HCl from the EDC cracking process. Since any acetylene fed to the oxychlorination reactor will be converted to highly chlorinated C2 by-products, selective hydrogenation of this acetylene to ethylene and ethane is widely used as a preventive measure (78,98—102). 

By-products from EDC pyrolysis typically include acetjiene, ethylene, methyl chloride, ethyl chloride, 1,3-butadiene, vinylacetylene, benzene, chloroprene, vinyUdene chloride, 1,1-dichloroethane, chloroform, carbon tetrachloride, 1,1,1-trichloroethane [71-55-6] and other chlorinated hydrocarbons (78). Most of these impurities remain with the unconverted EDC, and are subsequendy removed in EDC purification as light and heavy ends. The lightest compounds, ethylene and acetylene, are taken off with the HCl and end up in the oxychlorination reactor feed. The acetylene can be selectively hydrogenated to ethylene. The compounds that have boiling points near that of vinyl chloride, ie, methyl chloride and 1,3-butadiene, will codistiU with the vinyl chloride product. Chlorine or carbon tetrachloride addition to the pyrolysis reactor feed has been used to suppress methyl chloride formation, whereas 1,3-butadiene, which interferes with PVC polymerization, can be removed by treatment with chlorine or HCl, or by selective hydrogenation. 

The hydrocarbon feed rate to the reactor also affects the burning kinetics in the regenerator. Increasing the reactor feed rate increases the coke production rate, which in turn requires that the air rate to the regenerator increase. Because the regenerator bed level is generally held constant, the air residence time in the dense phase decreases. This decrease increases the O2 content in the dilute phase and increases afterbum (Fig. 5). 

Increasing the nitrogen content in the reactor feed generally increases NO emissions in the regenerator. Increasing feed nitrogen content from 200—300 ppm to >100 ppm has been reported to increase NO emissions from 50 ppm to >450 ppm (46). 

Two variables of primary importance, which are interdependent, are reaction temperature and ch1orine propy1ene ratio. Propylene is typically used ia excess to act as a diluent and heat sink, thus minimising by-products (eqs.2 and 3). Since higher temperatures favor the desired reaction, standard practice generally involves preheat of the reactor feeds to at least 200°C prior to combination. The heat of reaction is then responsible for further increases in the reaction temperature toward 510°C. The chlorine propylene ratio is adjusted so that, for given preheat temperatures, the desired ultimate reaction temperature is maintained. For example, at a chlorine propylene molar ratio of 0.315, feed temperatures of 200°C (propylene) and 50°C (chlorine) produce an ultimate reaction temperature of approximately 500°C (10). Increases in preheat temperature toward the ultimate reactor temperature, eg, in attempts to decrease yield of equation 1, must be compensated for in reduced chlorine propylene ratio, which reduces the fraction of propylene converted and, thus aHyl chloride quantity produced. A suitable economic optimum combination of preheat temperature and chlorine propylene ratio can be readily deterrnined for individual cases. 

EPM and EPDM mbbers are produced in continuous processes. Most widely used are solution processes, in which the polymer produced is in the dissolved state in a hydrocarbon solvent (eg, hexane). These processes can be grouped into those in which the reactor is completely filled with the Hquid phase, and those in which the reactor contents consist pardy of gas and pardy of a Hquid phase. In the first case the heat of reaction, ca 2500 kJ (598 kcal)/kg EPDM, is removed by means of cooling systems, either external cooling of the reactor wall or deep-cooling of the reactor feed. In the second case the evaporation heat from unreacted monomers also removes most of the heat of reaction. In other processes using Hquid propylene as a dispersing agent, the polymer is present in the reactor as a suspension. In this case the heat of polymerisation is removed mainly by monomer evaporation. 

The per pass ethylene conversion in the primary reactors is maintained at 20—30% in order to ensure catalyst selectivities of 70—80%. Vapor-phase oxidation inhibitors such as ethylene dichloride or vinyl chloride or other halogenated compounds are added to the inlet of the reactors in ppm concentrations to retard carbon dioxide formation (107,120,121). The process stream exiting the reactor may contain 1—3 mol % ethylene oxide. This hot effluent gas is then cooled ia a shell-and-tube heat exchanger to around 35—40°C by usiag the cold recycle reactor feed stream gas from the primary absorber. The cooled cmde product gas is then compressed ia a centrifugal blower before entering the primary absorber. 

Relationships Between Objects, Processes, and Events. Relationships can be causal, eg, if there is water in the reactor feed, then an explosion can take place. Relationships can also be stmctural, eg, a distiUation tower is a vessel containing trays that have sieves in them or relationships can be taxonomic, eg, a boiler is a type of heat exchanger. Knowledge in the form of relationships connects facts and descriptions that are already represented in some way in a system. Relational knowledge is also subject to uncertainty, especiaUy in the case of causal relationships. The representation scheme has to be able to express this uncertainty in some way. 

When the solid is one of the reactants, such as in ore roasting, the flow must be continuous and precise in order to maintain constant conditions in the reactor. Feeding of free-flowing granular solids into a fluidized bed is not difficult. Standard commercially available sohds-weighiug and -conveying equipment can be used to control the rate and dehver the solids to the feeder. Screw conveyors, dip pipes, seal legs, and injectors are used to introduce the solids into the reactor... 

REACTL Totalizer for reactor feed PBF Product B to fractionation section... 

In the feed preparation section, those materials are removed from the reactor feed which would either poison the catalyst or which would give rise to compounds detrimental to product quality. Hydrogen sulfide is removed in the DBA tower, and mercaptans are taken out in the caustic wash. The water wash removes traces of caustic and DBA, both of which are serious catalyst poisons. Also, the water wash is used to control the water content of the reactor feed (which has to be kept at a predetermined level to keep the polymerization catalyst properly hydrated) and remove NH3, which would poison the catalyst. Diolefins and oxygen should also be kept out of poly feed for good operation. 

The common practice in semi-regenerative Powerformers is to desulfurize the reactor feed. This reduces the deactivation rate of the Powerforming catalyst,... 

The reactor feed may be preheated and the feed pressure may alter. The volumetric flowrate of gases depends on the reactor temperature and pressure at fixed mass flowrate. In many cases, the feed is liquid at room temperature, while the reaction mixture is a gas at the higher temperature in the reactor. In these instances, the performance of the reactor is represented as conversion and selectivity against the liquid hourly space velocity (LHSV). This is defined as... 

---