Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Properties, temperature dependency

Solubility in mole fractions. AG in kJ mol-1 AS in J K l mol-1 rs in °C. The properties of the last three substances in their hypothetical liquid state under standard conditions were estimated by appropriate conversion from gas to dissolved state thermodynamic properties. Temperature dependence of heat capacity change described by exponential scaling (see p. 217). [Pg.215]

There are various methods of the glass transition temperature evaluation based on temperature dependence of polymer physical properties in the interval of glass transition 1) specific volume of polymer at slow cooling (dilatometric method) 2) heat capacity (calorimetric method),3) refraction index (refractometric method) 4) mechanical properties 5) electrical properties (temperature dependence of electric conductivity) or maximum of dielectric loss 6) NMR ° 7) electronic paramagnetic resonance, etc. [Pg.218]

The fact that plastics are good insulators does not mean that plastics are inert in an electrical field. They can in fact, be made to conduct electricity by the addition of fillers such as carbon black and metallic flake. The type and degree of interaction depends on the polarity of the basic resin material and the ability of an electrical field to produce ions that will cause current flows. In most applications for plastics, the intrinsic properties of the polymer are related to the performance under specific test conditions. The properties of interest are the dielectric strength, the dielectric constant at a range of frequencies, the dielectric loss factor at a range of frequencies, the volume resistivity, the surface resistivity, and the arc resistance. The last three are sensitive to moisture content in many materials. These properties are determined by the use of standardized tests described by ASTM (Table 16-1). These properties of the plastics are temperature dependent as are many of their other properties. Temperature dependence must be recognized to avoid problems in electrical products made of plastics. [Pg.302]

Investigation of unique ionic liquid combinations and compositions to optimize physical properties, temperature dependence, and electrode compatibility... [Pg.345]

Find the temperature distribution for a viscous fluid in steady flow between two broad parallel plates both of which are at Tq. Consider viscous dissipation but neglect property temperature dependence. [Pg.121]

Glassy state structural components distinction defines their behavior distinctions in both deformation [46] and relaxation [47] processes. It is known [48, 49], that in its turn polymers glassy state includes a substates number, differing by mechanical properties temperature dependences. A breaking (bend) on the corresponding parameter dependence, for example, of yield stress on temperature, is a typical indication of transition from one substate to another. At present unequivocal structural identification of these states is... [Pg.26]

Thermal and electrochemical coupling emanates from temperature-dependent physicochemical properties. Temperature dependence of physicochemical properties, r, can be described by the Arrhenius expression [33, 51] ... [Pg.856]

The radiation and temperature dependent mechanical properties of viscoelastic materials (modulus and loss) are of great interest throughout the plastics, polymer, and rubber from initial design to routine production. There are a number of laboratory research instruments are available to determine these properties. All these hardness tests conducted on polymeric materials involve the penetration of the sample under consideration by loaded spheres or other geometric shapes [1]. Most of these tests are to some extent arbitrary because the penetration of an indenter into viscoelastic material increases with time. For example, standard durometer test (the "Shore A") is widely used to measure the static "hardness" or resistance to indentation. However, it does not measure basic material properties, and its results depend on the specimen geometry (it is difficult to make available the identity of the initial position of the devices on cylinder or spherical surfaces while measuring) and test conditions, and some arbitrary time must be selected to compare different materials. [Pg.239]

Furthermore, most physicochemical properties are related to interactions between a molecule and its environment. For instance, the partitioning between two phases is a temperature-dependent constant of a substance with respect to the solvent system. Equation (1) therefore has to be rewritten as a function of the molecular structure, C, the solvent, S, the temperature, X etc. (Eq. (2)). [Pg.488]

CHEOPS is based on the method of atomic constants, which uses atom contributions and an anharmonic oscillator model. Unlike other similar programs, this allows the prediction of polymer network and copolymer properties. A list of 39 properties could be computed. These include permeability, solubility, thermodynamic, microscopic, physical and optical properties. It also predicts the temperature dependence of some of the properties. The program supports common organic functionality as well as halides. As, B, P, Pb, S, Si, and Sn. Files can be saved with individual structures or a database of structures. [Pg.353]

Molality is used in thermodynamic calculations where a temperature independent unit of concentration is needed. Molarity, formality and normality are based on the volume of solution in which the solute is dissolved. Since density is a temperature dependent property a solution s volume, and thus its molar, formal and normal concentrations, will change as a function of its temperature. By using the solvent s mass in place of its volume, the resulting concentration becomes independent of temperature. [Pg.18]

Activated carbons contain chemisorbed oxygen in varying amounts unless special cate is taken to eliminate it. Desired adsorption properties often depend upon the amount and type of chemisorbed oxygen species on the surface. Therefore, the adsorption properties of an activated carbon adsorbent depend on its prior temperature and oxygen-exposure history. In contrast, molecular sieve 2eohtes and other oxide adsorbents are not affected by oxidi2ing or reducing conditions. [Pg.277]

Chlorine, a member of the halogen family, is a greenish yellow gas having a pungent odor at ambient temperatures and pressures and a density 2.5 times that of air. In Hquid form it is clear amber SoHd chlorine forms pale yellow crystals. The principal properties of chlorine are presented in Table 15 additional details are available (77—79). The temperature dependence of the density of gaseous (Fig. 31) and Hquid (Fig. 32) chlorine, and vapor pressure (Fig. 33) are illustrated. Enthalpy pressure data can be found in ref. 78. The vapor pressure P can be calculated in the temperature (T) range of 172—417 K from the Martin-Shin-Kapoor equation (80) ... [Pg.505]

Chemical Properties. The hydrolysis of PET is acid- or base-catalyzed and is highly temperature dependent and relatively rapid at polymer melt temperatures. Treatment for several weeks in 70°C water results in no significant fiber strength loss. However, at 100°C, approximately 20% of the PET tenacity is lost in one week and about 60% is lost in three weeks (47). In general, the hydrolysis and chemical resistance of copolyester materials is less than that for PET and depends on both the type and amount of comonomer. [Pg.326]

The properties of butane and isobutane have been summarized ia Table 5 and iaclude physical, chemical, and thermodynamic constants, and temperature-dependent parameters. Graphs of several physical properties as functions of temperature have been pubUshed (17) and thermodynamic properties have been tabulated as functions of temperature (12). [Pg.401]

Anhydrous Hydrogen Chloride. Anhydrous hydrogen chloride is a colorless gas that condenses to a colorless liquid and freezes to a white crystalline solid. The physical and thermodynamic properties of HCl are summarized in Table 2 for selected temperatures and pressures. Figure 1 shows the temperature dependence of some of these properties. [Pg.437]

The physical properties of some common ketones are Hsted in Table 1. Ketones are commonly separated by fractional distillation, and vapor—Hquid equihbria and vapor pressure data are readily available for common ketones. A number of other temperature dependent physical properties for acetone, methyl ethyl ketone, methyl isobutyl ketone, and diethyl ketone have been pubHshed (3). [Pg.485]

Other Properties. The glass-transition temperature for PPO is 190 K and varies htde with molecular weight (182). The temperature dependence of the diffusion coefficient of PPO in the undiluted state has been measured (182). [Pg.355]

The design of shape-memory devices is quite different from that of conventional alloys. These materials are nonlinear, have properties that are very temperature-dependent, including an elastic modulus that not only increases with increasing temperature, but can change by a large factor over a small temperature span. This difficulty in design has been addressed as a result of the demands made in the design of compHcated smart and adaptive stmctures. Informative references on all aspects of SMAs are available (7—9). [Pg.466]


See other pages where Properties, temperature dependency is mentioned: [Pg.378]    [Pg.83]    [Pg.2]    [Pg.1153]    [Pg.79]    [Pg.124]    [Pg.781]    [Pg.582]    [Pg.355]    [Pg.378]    [Pg.83]    [Pg.2]    [Pg.1153]    [Pg.79]    [Pg.124]    [Pg.781]    [Pg.582]    [Pg.355]    [Pg.231]    [Pg.2419]    [Pg.2565]    [Pg.163]    [Pg.90]    [Pg.92]    [Pg.324]    [Pg.192]    [Pg.207]    [Pg.144]    [Pg.146]    [Pg.27]    [Pg.133]    [Pg.376]    [Pg.382]    [Pg.339]    [Pg.343]    [Pg.500]    [Pg.223]    [Pg.498]    [Pg.115]   


SEARCH



© 2024 chempedia.info