Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Properties species

Approximately three hundred dimensionless groups [6.23] are used to describe the most important problems that characterize chemical engineering processes. Out of these, only a limited number is frequently used and can be classified according to the flow involved in the investigated process, the transport and interface transfer of one property (species, enthalpy, pressure) and the interactions of the transport mechanisms of the properties. In order to be considered in this anal-... [Pg.493]

Molar or specific value, extensive tlrenrrodyiramic property Partial property, species i in solution Excess property == M — M "... [Pg.759]

Formulas for safety factors are calculated according to cumulative properties, species sensitivity coefficient, and occurrence of delayed adverse effects (Sidorov 1980). It should be noted that the safety factor is designed mainly to allow for the potentially higher sensitivity of humans to specific pesticides than laboratory animals. This factor should also ensure the safety of a selected dose or concentration if new, unexpected adverse properties are identified for the substance in question. The final adjustment of health standards is based on clinical and epidemiological examinations of people exposed to that substance. [Pg.109]

Aluminosilicates are important as both inorganic compounds and as minerals and mineral glasses. Quantum mechanical calculations on cluster models for aluminosilicates can now accurately reproduce their energetic, structural and spectral properties. Species in glasses can be identified by matching their calculated spectral properties with experiment. More important, such calculations provide a framework for relating the structures and properties of inorganic aluminosilicates and their mineral coimterparts. [Pg.165]

Near-infrared (NIR) spectroscopy has been found to be a useful technique to characterize raw materials and finished textile products, and NIR methods and techniques continue to find increasingly diverse and wide-ranging quantitative and qualitative applications in the textile industry. Quantitative analyses determine the amount (or quantity) of the property/species of interest in a substance or material. Qualitative analyses can be used to either identify a specific species or subsfance present in a material (i.e., coating on a fiber), the type of material itself (i.e., cotton, nylon, or polyester), or the quality of the material. NIR quantitative and qualitative methods allow the user to rapidly, accurately, and precisely monitor key chemical, physical, and morphological properties of textile fibers, yarns, fabrics, and chemical textile auxiliaries. Chemical properties are specific chemical species or groups present in the material (i.e., CH, OH, NH) that result in NIR spectral absorbencies at distinctive... [Pg.485]

Factors a, b, and c are important for production, and for the application properties. Species from Eq. (1), of course, do not exist in solution. For the crystallization mechanism, reaction with real species should be presented. In an ideal case, when waterglass consists of monomeric species only, the reaction is given by NaH3Si04 (aq.) + [Al(OH)4] Na (aq.)... [Pg.23]

When used to separate solid-solid mixtures, the material is ground to a particle size small enough to liberate particles of the chemical species to be recovered. The mixture of solid particles is then dispersed in the flotation medium, which is usually water. Gas bubbles become attached to the solid particles, thereby allowing them to float to the surface of the liquid. The solid partices are collected from the surface by an overflow weir or mechanical scraper. The separation of the solid particles depends on the different species having different surface properties such that one species is preferentially attached to the bubbles. A number of chemicals are added to the flotation medium to meet the various requirements of the flotation process ... [Pg.70]

There is a large volume of contemporary literature dealing with the structure and chemical properties of species adsorbed at the solid-solution interface, making use of various spectroscopic and laser excitation techniques. Much of it is phenomenologically oriented and does not contribute in any clear way to the surface chemistry of the system included are many studies aimed at the eventual achievement of solar energy conversion. What follows here is a summary of a small fraction of this literature, consisting of references which are representative and which also yield some specific information about the adsorbed state. [Pg.418]

Other properties of association colloids that have been studied include calorimetric measurements of the heat of micelle formation (about 6 kcal/mol for a nonionic species, see Ref. 188) and the effect of high pressure (which decreases the aggregation number [189], but may raise the CMC [190]). Fast relaxation methods (rapid flow mixing, pressure-jump, temperature-jump) tend to reveal two relaxation times t and f2, the interpretation of which has been subject to much disagreement—see Ref. 191. A fast process of fi - 1 msec may represent the rate of addition to or dissociation from a micelle of individual monomer units, and a slow process of ti < 100 msec may represent the rate of total dissociation of a micelle (192 see also Refs. 193-195). [Pg.483]

Of course, condensed phases also exliibit interesting physical properties such as electronic, magnetic, and mechanical phenomena that are not observed in the gas or liquid phase. Conductivity issues are generally not studied in isolated molecular species, but are actively examined in solids. Recent work in solids has focused on dramatic conductivity changes in superconducting solids. Superconducting solids have resistivities that are identically zero below some transition temperature [1, 9, 10]. These systems caimot be characterized by interactions over a few atomic species. Rather, the phenomenon involves a collective mode characterized by a phase representative of the entire solid. [Pg.87]

Equation (A2.1.23) can be mtegrated by the following trick One keeps T, p, and all the chemical potentials p. constant and increases the number of moles n. of each species by an amount n. d where d is the same fractional increment for each. Obviously one is increasing the size of the system by a factor (1 + dQ, increasing all the extensive properties U, S, V, nl) by this factor and leaving the relative compositions (as measured by the mole fractions) and all other intensive properties unchanged. Therefore, d.S =. S d, V=V d, dn. = n. d, etc, and... [Pg.344]

At low currents, the rate of change of die electrode potential with current is associated with the limiting rate of electron transfer across the phase boundary between the electronically conducting electrode and the ionically conducting solution, and is temied the electron transfer overpotential. The electron transfer rate at a given overpotential has been found to depend on the nature of the species participating in the reaction, and the properties of the electrolyte and the electrode itself (such as, for example, the chemical nature of the metal). [Pg.603]

Atmospheric ions are important in controlling atmospheric electrical properties and conmumications and, in certain circumstances, aerosol fomiation [128. 130. 131. 138. 139, 140. 141. 142, 143, 144 and 145]. In addition, ion composition measurements can be used to derive trace neutral concentrations of the species involved in the chemistry. Figure A3.5.11 shows the total-charged-particle concentration as a frmction of... [Pg.817]

Adsorptive stripping analysis involves pre-concentration of the analyte, or a derivative of it, by adsorption onto the working electrode, followed by voltanmietric iiieasurement of the surface species. Many species with surface-active properties are measurable at Hg electrodes down to nanoniolar levels and below, with detection limits comparable to those for trace metal detemiination with ASV. [Pg.1932]

The combination of electrochemistry and photochemistry is a fonn of dual-activation process. Evidence for a photochemical effect in addition to an electrochemical one is nonnally seen m the fonn of photocurrent, which is extra current that flows in the presence of light [, 89 and 90]. In photoelectrochemistry, light is absorbed into the electrode (typically a semiconductor) and this can induce changes in the electrode s conduction properties, thus altering its electrochemical activity. Alternatively, the light is absorbed in solution by electroactive molecules or their reduced/oxidized products inducing photochemical reactions or modifications of the electrode reaction. In the latter case electrochemical cells (RDE or chaimel-flow cells) are constmcted to allow irradiation of the electrode area with UV/VIS light to excite species involved in electrochemical processes and thus promote fiirther reactions. [Pg.1945]

The species at the centre of tire rings is usually Si or Ge and tire bridging atom is oxygen. In one study tire peripheral hydrogens on tire phtlialocyanine molecules were replaced by alkyl groups and tire resulting polymers could be rendered soluble in ordinary organic solvents [108, 109 and 110]. Successful deposition of several of tliese materials has been achieved and different techniques were employed to study tlieir stmctural properties [109, ill, ill, ill and 1141. [Pg.2620]


See other pages where Properties species is mentioned: [Pg.204]    [Pg.229]    [Pg.234]    [Pg.1390]    [Pg.486]    [Pg.252]    [Pg.204]    [Pg.229]    [Pg.234]    [Pg.1390]    [Pg.486]    [Pg.252]    [Pg.224]    [Pg.293]    [Pg.398]    [Pg.418]    [Pg.480]    [Pg.519]    [Pg.588]    [Pg.34]    [Pg.192]    [Pg.815]    [Pg.870]    [Pg.1119]    [Pg.1438]    [Pg.1714]    [Pg.1781]    [Pg.1889]    [Pg.1947]    [Pg.2361]    [Pg.2391]    [Pg.2400]    [Pg.2413]    [Pg.2422]    [Pg.2422]    [Pg.2439]    [Pg.2489]    [Pg.2577]    [Pg.2743]    [Pg.2808]   
See also in sourсe #XX -- [ Pg.245 , Pg.246 ]




SEARCH



Antioxidant properties reactive oxygen species

Aqueous species, thermodynamic properties

Biochemical reactions species reactants, transformed properties

Calculations of species properties

Chemical species thermodynamical properties

Determining species thermochemical properties

Fiber properties of different wood species

Formation of Surface Alkoxy Species with Carbenium-Ion-Like Properties

K.A. Gingerich, Thermodynamic properties of gaseous species

Linear species symmetry properties

Myoglobin properties,species differences

Non-Linear Optical Properties of Supramolecular Species

Property types pure species

Reactive oxygen species , basic properties

Species and Properties of Interest

Surface alkoxy species, with carbenium-ion-like properties

Thermodynamic properties biochemical species

Thermodynamics species/reactants, transformed properties

© 2024 chempedia.info