Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Polymer film, electrical insulator

The principal uses of biaxially oriented PET film are in capacitors, in slot liners for motors, and for magnetic tape. Although a polar polymer, its electrical insulation properties at room temperature are good (even at high frequencies) because at room temperature, which is well below Tg (69°C), dipole orientation is severely restricted. [Pg.436]

Most pure polymers are electrical insulators. However, polymers take up electrical charges and such static charge causes problems such as dust attraction, adhering of fibers or films to surfaces during processing, and spark discharge in electronic devices and flammable gases. [Pg.144]

Mouldings or film. High-temperature polymer. Excellent electrical insulator. Low coefficient of sliding friction. Expensive, e.g. Teflon , Fluon . [Pg.332]

Poly(phenylquinoxaline—arnide—imides) are thermally stable up to 430°C and are soluble in polar organic solvents (17). Transparent films of these materials exhibit electrical insulating properties. Quinoxaline—imide copolymer films prepared by polycondensation of 6,6 -meth5lene bis(2-methyl-3,l-benzoxazine-4-one) and 3,3, 4,4 -benzophenone tetracarboxyUc dianhydride and 4,4 -oxydianiline exhibit good chemical etching properties (18). The polymers are soluble, but stable only up to 200—300°C. [Pg.532]

The commercial polymers are mechanically similar to PTFE but with a somewhat greater impact strength. They also have the same excellent electrical insulation properties and chemical inertness. Weathering tests in Florida showed no change in properties after four years. The material also shows exceptional non-adhesiveness. The coefficient of friction of the resin is low but somewhat higher than that of PTFE. Films up to 0.010 in thick show good transparency. [Pg.373]

Most polymers are very good electrical insulating materials because of their chemical composition, i.e., their electrical conductivity is exceptionally low. Because of this important property, many plastics are used to produce electrically nonconductive parts. However, the high surface resistance leads to an unwanted property the material is prone to electrostatic charge accumulation. To facilitate dissipation of the charge, antistatic agents are incorporated, which combine with atmospheric moisture on the plastic surface to form a conductive film. [Pg.208]

Polymers are widely used as electrical insulators in applications such as wire and cable insulation, electrical appliance housings and capacitor films. Polymers used in these applications include polyvinyl chloride, polyethylene, and isotactic polypropylene. [Pg.37]

They produced high performance electrets from thin polymer films metallized so as to yield high capacitance. Both electrical and mechanical properties of these transducers have been remarkable examples of how applications of science of solids, including knowledge of electron traps, conduction processes in insulators and the viscoelastic phenomena of semicrystalline polymers, can be combined.(6) Incidentally, similar ideas have been applied to optimization of the properties of particle microphones, through assemblies of perfectly microspherical polymer carbon systems. These have shown what limits of performance... [Pg.167]

Polyethylene. The most straightforward process for the production of polymers from ethylene is that of the direct polymerization of the olefin. The polymerization process usually requires pressures and temperatures of 15,000 to 30,000 pounds per square inch and 200° to 300° C., and may be effected in either gas or liquid phase reactions (9). The polymer of molecular weight above 20,000 is the white, translucent plastic, polyethylene, widely used in electrical insulation, packaging material for foods, cosmetics and pharmaceuticals, liners for paper bags, etc. Articles molded from polyethylene are semirigid or rigid, depending on their thickness, but in thin films the material has excellent flexibility, even at relatively low temperatures. [Pg.313]

As described in the introduction, submicrometer disk electrodes are extremely useful to probe local chemical events at the surface of a variety of substrates. However, when an electrode is placed close to a surface, the diffusion layer may extend from the microelectrode to the surface. Under these conditions, the equations developed for semi-infinite linear diffusion are no longer appropriate because the boundary conditions are no longer correct [97]. If the substrate is an insulator, the measured current will be lower than under conditions of semi-infinite linear diffusion, because the microelectrode and substrate both block free diffusion to the electrode. This phenomena is referred to as shielding. On the other hand, if the substrate is a conductor, the current will be enhanced if the couple examined is chemically stable. For example, a species that is reduced at the microelectrode can be oxidized at the conductor and then return to the microelectrode, a process referred to as feedback. This will occur even if the conductor is not electrically connected to a potentiostat, because the potential of the conductor will be the same as that of the solution. Both shielding and feedback are sensitive to the diameter of the insulating material surrounding the microelectrode surface, because this will affect the size and shape of the diffusion layer. When these concepts are taken into account, the use of scanning electrochemical microscopy can provide quantitative results. For example, with the use of a 30-nm conical electrode, diffusion coefficients have been measured inside a polymer film that is itself only 200 nm thick [98]. [Pg.398]

The polyethene produced in this way has from 100 to 1000 ethene units in the hydrocarbon chain. The polymer possesses a number of desirable properties as a plastic and is used widely for electrical insulation, packaging films, piping, and a variety of molded articles. Propene and 2-methylpropene do not polymerize satisfactorily by radical mechanisms. [Pg.396]

Because the oxidation potential of the polymer is lower than that of the monomer, the polymer is electrochemically oxidized into a conducting state, kept electrically neutral by incorporation of the electrolyte anion as a counter-ion. This is an essential since precipitation of the unoxidized, insulating polymer would stop the reaction. Both coulometric measurements and elemental analysis show approximately one counter-ion per four repeat units. An important feature is the fact that the polymerization is not reversible whereas the oxidation of the polymer is. If the polymer film is driven cathodic then it is reduced towards the undoped state. At the same time neutrality is maintained by diffusion of the counter-ions out of the film and into the electrolyte. This process is reversible over many cycles provided that the film is not undoped to the point where it becomes too insulating. It is possible to use it to put new counter-ions into the film, allowing the introduction of ions which are too nucleophilic to be used in the synthesis. The conductivity of the film for a given degree of oxidation depends markedly on the counter-ion, varying by a factor of up to 105. [Pg.19]


See other pages where Polymer film, electrical insulator is mentioned: [Pg.163]    [Pg.378]    [Pg.407]    [Pg.449]    [Pg.45]    [Pg.205]    [Pg.472]    [Pg.576]    [Pg.261]    [Pg.183]    [Pg.24]    [Pg.905]    [Pg.121]    [Pg.645]    [Pg.458]    [Pg.472]    [Pg.301]    [Pg.236]    [Pg.196]    [Pg.7]    [Pg.77]    [Pg.539]    [Pg.449]    [Pg.3]    [Pg.170]    [Pg.150]    [Pg.543]    [Pg.799]    [Pg.653]    [Pg.253]    [Pg.181]    [Pg.24]    [Pg.100]    [Pg.255]   
See also in sourсe #XX -- [ Pg.646 ]




SEARCH



Electric insulation

Electric polymers

Electrical insulation

Electricity insulators

Insulating films

Insulator, polymer film

Insulators, electric

Polymers electrical

Polymers insulators

© 2024 chempedia.info