Polyether agents

See Antibiotics, polyethers Antibiotics, peptides Chelating agents. 

Polyethers. Antibiotics within this family contain a number of cycHc ether and ketal units and have a carboxyHc acid group. They form complexes with mono- and divalent cations that ate soluble ia aoapolar organic solvents. They iateract with bacterial cell membranes and allow cations to pass through the membranes causiag cell death. Because of this property they have been classified as ionophores. Monensia, lasalocid, and maduramicia are examples of polyethers that are used commercially as anticoccidial agents ia poultry and as growth promotants ia mmiaants. 

Coccidiosis is a proto2oal disease of the intestinal tract of animals that leads to severe loss of productivity and death. The development and widespread use of anticoccidials has revolutionized the poultry industry. The estimated world market for anticoccidial agents in 1989 was 425 million and this was dominated by the polyether ionophore antibiotics monensin, salinomycin [53003-10-4], n imsm [55134-13-9], la.s9locid, and maduramicin [84878-61-5] (26). 

Heat-SensitiZingProcess. Another process used to make latex mbber articles of thicker section involves sensitizing the compound so that it coagulates when heated to a given temperature, then using heated molds to build the article to the desired thickness. Ammonia-preserved latex is used in this process, and polyether, polythioether, or poly(vinyl methyl ether) (PVME) can be used as heat-sensitizing agents. 

Treponema hjoepsenteriae a causative agent of swine dysentery, is sensitive to polyether antibiotics at low concentrations in vitro. In pigs, lasalocid was effective in controlling dysentery at levels of 0.005—0.05% in feeds (167). Several species of Mycoplasma are inhibited in vitro at a MIC range of 2.0—25 p./mL of polyethers including narasin, cartiomycin, and K41 (164). 

See Antibiotics, polyethers Catalysis, phase-transfer Chelating agents. 

AH of the polyether elastomers, like other vulcanizable elastomers, can be compounded with processing aids, fillers, plasticizers, stabilizers, and vulcanizing agents to make useful mbber products. A typical compounding recipe for epichlorohydrin elastomer is as follows ... 

Curing Systems. The most commonly used vulcanizing agent for the polyethers not containing AGE, that is, ECH and ECH—EO, is 2-mercaptoimidazoline, also called ethylenethiourea [96-45-7]. Other commercially appHed curing agents include derivatives of 2,5-dimercapto-l,3,4-thiadiazole, trithiocyanuric acid and derivatives, bisphenols, diamines, and other substituted thioureas. 

The first type includes vulcanising agents, such as sulphur, selenium and sulphur monochloride, for diene rubbers formaldehyde for phenolics diisocyanates for reaction with hydrogen atoms in polyesters and polyethers and polyamines in fluoroelastomers and epoxide resins. Perhaps the most well-known cross-linking initiators are peroxides, which initiate a double-bond... 

Surface active agents are important components of foam formulations. They decrease the surface tension of the system and facilitate the dispersion of water in the hydrophobic resin. In addition they can aid nucleation, stabilise the foam and control cell structure. A wide range of such agents, both ionic and non-ionic, has been used at various times but the success of the one-shot process has been due in no small measure to the development of the water-soluble polyether siloxanes. These are either block or graft copolymers of a polydimethylsiloxane with a polyalkylene oxide (the latter usually an ethylene oxide-propylene oxide copolymer). Since these materials are susceptible to hydrolysis they should be used within a few days of mixing with water. 

Formulations for one-shot polyether systems are similar to those used for flexible foams and contain polyether, isocyanate, catalyst, surfactant and water. Trichloroethyl phosphate is also often used as a flame retardant. As with polyesters, diphenylmethane di-isocyanate is usually preferred to TDI because of its lower volatility. Tertiary amines and organo-tin catalysts are used as with the flexible foams but not necessarily in combination. Silicone oil surfactants are again found to be good foam stabilisers. Volatile liquids such as trichlorofluoro-methane have been widely used as supplementary blowing agents and give products of low density and of very low thermal conductivity. 

Saturated hydrocarbons such as neopentane, notbomane, and cyclooctane have been converted to the corresponding perfluoro derivatives in 10-20% yield by gas-phase reaction with fluorine gas diluted with helium at —78°C. Simple ethers can be completely fluorinated under similar conditions. Crown polyethers can be fluorinated by passing an Fa/He stream over a solid mixture of sodium fluoride and the crown ether. Liquid-phase fluorination of hydrocarbons has also been observed, but the reaction is believed to be ionic, rather than radical, in character. A variety of milder fluorination agents have been developed for synthetic purposes and will be discussed in Chapter 6 of Part B. 

Venustatriol, a marine-derived antiviral agent, as with many polyether structures, is a straightforward problem for retrosynthetic analysis. The major issues, clearance of stereocenters and topologically strategic disconnection, were readily resolved to generate the pathway of synthesis described below. 

In a similar way, polyester block copolymers were obtained by reacting acid chloride-terminated polyesters with hydroxy-terminated polyethers,401 or by reacting polyester-containing polymer mixtures with coupling agents such as diisocyanates.402... 

Anti-protozoa agents are utilized to treat diseases such as coccidiosis, which affects many farm animals, particularly poultry. Coccidiostats include polyether monocar-boxylic acid ionophores and other types of compounds. Polyether monocarboxylic acid ionophores include monesin, narasin, lasalocid, and salinomycin. The most common of these is salinomycin. Nonionophore coccidiostats include dimetridazole and halofunginone. Stanker et al. reviewed immunoassays available for coccidio-static agents. 

Polyether-based foams account for more than 90% of all flexible polyurethane foams. The properties of foams are controlled by the molecular structure of the precursors and the reaction conditions. In general, density decreases as the amount of water increases, which increases the evolution of carbon dioxide. However, the level of water that can be used is limited by the highly exothermic nature of its reaction with isocyanate, which carries with it the risk of self-ignition of the foamed product. If very low density foams are desired, additional blowing agents, such as butane, are incorporated within the mixing head. 

---