Poly factors

Kleijnen J.P.C. (1975). Screening designs for poly-factor experimentation. Tet lwo-metrics, 18.487-493. 

If tlie level(s) associated witli tlie defect are deep, tliey become electron-hole recombination centres. The result is a (sometimes dramatic) reduction in carrier lifetimes. Such an effect is often associated witli tlie presence of transition metal impurities or certain extended defects in tlie material. For example, substitutional Au is used to make fast switches in Si. Many point defects have deep levels in tlie gap, such as vacancies or transition metals. In addition, complexes, precipitates and extended defects are often associated witli recombination centres. The presence of grain boundaries, dislocation tangles and metallic precipitates in poly-Si photovoltaic devices are major factors which reduce tlieir efficiency. 

The time-temperature superpositioning principle was applied f to the maximum in dielectric loss factors measured on poly(vinyl acetate). Data collected at different temperatures were shifted to match at Tg = 28 C. The shift factors for the frequency (in hertz) at the maximum were found to obey the WLF equation in the following form log co + 6.9 = [ 19.6(T -28)]/[42 (T - 28)]. Estimate the fractional free volume at Tg and a. for the free volume from these data. Recalling from Chap. 3 that the loss factor for the mechanical properties occurs at cor = 1, estimate the relaxation time for poly(vinyl acetate) at 40 and 28.5 C. 

Williams and Ferryf measured the dynamic compliance of poly(methyl acrylate) at a number of temperatures. Curves measured at various temperatures were shifted to construct a master curve at 25°C, and the following shift factors were obtained ... 

The solute molecular weight enters the van t Hoff equation as the factor of proportionality between the number of solute particles that the osmotic pressure counts and the mass of solute which is known from the preparation of the solution. The molecular weight that is obtained from measurements on poly disperse systems is a number average quantity. 

Chain transfer to solvent is an important factor in controlling the molecular weight of polymers prepared by this method. The chain-transfer constants for poly(methyl methacrylate) in various common solvents (C) and for various chain-transfer agents are Hsted in Table 10. 

Electrical Properties. AH polyolefins have low dielectric constants and can be used as insulators in particular, PMP has the lowest dielectric constant among all synthetic resins. As a result, PMP has excellent dielectric properties and alow dielectric loss factor, surpassing those of other polyolefin resins and polytetrafluoroethylene (Teflon). These properties remain nearly constant over a wide temperature range. The dielectric characteristics of poly(vinylcyclohexane) are especially attractive its dielectric loss remains constant between —180 and 160°C, which makes it a prospective high frequency dielectric material of high thermal stabiUty. 

The seam closure on a folding carton is typicahy made using a latex, poly(vinyl acetate), vinyl acetate copolymer, or hot-melt adhesive (27). The choice of adhesive depends on a number of factors, including the nature of any coating used on the package and the production speeds required. 

Often poly(ethylene glycol)s or derivatives thereof can be used instead of crowns or onium salts advantageously, although their catalytic activity frequently tends to be somewhat lower. The possible toxicity of crowns and cryptands and the price difference between these compounds and onium salts (100 1 to 10 1) are other important factors to be considered. Thus (1) [17455-13-9] (2) [14187-32-7] and (3) [16069-36-6] and cryptands are used more often in laboratory work, whereas onium salts are more important for industrial processes. 

Dichlorobenzene. T -Dichlorobenzene s largest and growing oudet is in the manufacture of poly(phenylene sulfide) resin (PPS). Other apphcations include room deodorant blocks and moth control, a market which is static and likely to remain unchanged but combined is currently a larger outlet than PPS. Small amounts ofT -dichlorobenzene are used in the production of 1,2,4-trichlorobenzene, dyes, and insecticide intermediates. Exports have been a principal factor in U.S. production with about 25% exported in 1988. 

In the case of polymer molecules where the dipoles are not directly attached to the main chain, segmental movement of the chain is not essential for dipole polarisation and dipole movement is possible at temperatures below the glass transition temperature. Such materials are less effective as electrical insulators at temperatures in the glassy range. With many of these polymers, e.g., poly(methyl methacrylate), there are two or more maxima in the power factor-temperature curve for a given frequency. The presence of two such maxima is due to the different orientation times of the dipoles with and without associated segmental motion of the main chain. 

It is obvious that the range of possible formulations based on poly(vinyl chloride) and related copolymers is very wide indeed. For each end-use the requirements must be carefully considered and a formulation devised that will give a compound of adequate properties at the lowest cost. In assessing cost it is not only important to consider the cost of the compound but also comparative processing costs, the possible cost of storing additional materials and many other cost factors. 

Polyesters are eneountered in many forms. They are important as laminating resins, moulding compositions, fibres, films, surface coating resins, rubbers and plasticisers. The common factor in these widely different materials is that they all contain a number of ester linkages in the main chain. (There are also a number of polymers such as poly(vinyl acetate) which contain a number of ester groups in side chains but these are not generally considered within the term polyester resins.)... 

---