Plasticator length

J.S. Stolken, A.G. Evans A microbend test method for measuring the plasticity length scale. Acta Mater. 46, 5109 (1998)... 

A piezo-composite consists of a piezoelectric active phase and a passive plastic phase [2]. In the 1-3-configuration adopted in our case, piezoelectric rods parallely aligned in thickness direction are imbedded in a three-dimensional plastic matrix (Fig. 1). The distance between the rods has to be chosen inferior to the half wave length of the shear wave in the matrix material ensuring that the whole compound is vibrating as a quasi-homogeneous material. 

Spencer, R. D. The Dependence of Strength in Plastics upon Polymer Chain Length and Chain Orientation, /. Chem. Educ. 1984, 61, 555-563. 

Knoop developed an accepted method of measuring abrasive hardness using a diamond indenter of pyramidal shape and forcing it into the material to be evaluated with a fixed, often 100-g, load. The depth of penetration is then determined from the length and width of the indentation produced. Unlike WoodeU s method, Knoop values are static and primarily measure resistance to plastic flow and surface deformation. Variables such as load, temperature, and environment, which affect determination of hardness by the Knoop procedure, have been examined in detail (9). 

Reinforcement. PVA fiber in the form of short cut chips having a length of several millimeters to several tens of millimeters is widely used as raw material for paper and for reinforcing plastics, cement, and the like, and has been acquiring more and more significance. 

Film and sheet are defined as flat unsupported sections of a plastic resia whose thickness is very thin ia relation to its width and length. Films are generally regarded as being 0.25 mm or less, whereas sheet may range from this thickness to several centimeters thick. Film and sheet may be used alone ia their unsupported state or may be combined through lamination, coextmsion, or coating. They may also be used in combination with other materials such as paper, foil, or fabrics. 

One simple rheological model that is often used to describe the behavior of foams is that of a Bingham plastic. This appHes for flows over length scales sufficiently large that the foam can be reasonably considered as a continuous medium. The Bingham plastic model combines the properties of a yield stress like that of a soHd with the viscous flow of a Hquid. In simple Newtonian fluids, the shear stress T is proportional to the strain rate y, with the constant of proportionaHty being the fluid viscosity. In Bingham plastics, by contrast, the relation between stress and strain rate is r = where is... 

Typically, soHd stabilizers utilize natural saturated fatty acid ligands with chain lengths of Cg—C g. Ziac stearate [557-05-1/, ziac neodecanoate [27253-29-8] calcium stearate [1592-23-0] barium stearate [6865-35-6] and cadmium laurate [2605-44-9] are some examples. To complete the package, the soHd products also contain other soHd additives such as polyols, antioxidants, and lubricants. Liquid stabilizers can make use of metal soaps of oleic acid, tall oil acids, 2-ethyl-hexanoic acid, octylphenol, and nonylphenol. Barium bis(nonylphenate) [41157-58-8] ziac 2-ethyIhexanoate [136-53-8], cadmium 2-ethyIhexanoate [2420-98-6], and overbased barium tallate [68855-79-8] are normally used ia the Hquid formulations along with solubilizers such as plasticizers, phosphites, and/or epoxidized oils. The majority of the Hquid barium—cadmium formulations rely on barium nonylphenate as the source of that metal. There are even some mixed metal stabilizers suppHed as pastes. The U.S. FDA approved calcium—zinc stabilizers are good examples because they contain a mixture of calcium stearate and ziac stearate suspended ia epoxidized soya oil. Table 4 shows examples of typical mixed metal stabilizers. 

Other important operating parameters include plasticizer changes, gas type and pressure, gap length between spinneret and quench bath, line speed, and rope tension. All variables must be carefully controlled to obtain a hoUow fiber of desired characteristics. 

Copper wines are used primarily because of thein economy and resistance to sweep, ie, tendency of the wine to move in a plane perpendicular to its length, during plastic encapsulation (11—16). Because copper is harder than gold, more attention is needed during the bonding operation to prevent the chip from cratering. Table 6 fists the various properties for wine materials. 

DiisononylPhthalate andDiisodeeylPhthalate. These primary plasticizers are produced by esterification of 0x0 alcohols of carbon chain length nine and ten. The 0x0 alcohols are produced through the carbonylation of alkenes (olefins). The carbonylation process (eq. 3) adds a carbon unit to an alkene chain by reaction with carbon monoxide and hydrogen with heat, pressure, and catalyst. In this way a Cg alkene is carbonylated to yield a alcohol a alkene is carbonylated to produce a C q alcohol. Due to the distribution of the C=C double bond ia the alkene and the varyiag effectiveness of certain catalysts, the position of the added carbon atom can vary and an isomer distribution is generally created ia such a reaction the nature of this distribution depends on the reaction conditions. Consequendy these alcohols are termed iso-alcohols and the subsequent phthalates iso-phthalates, an unfortunate designation ia view of possible confusion with esters of isophthaUc acid. 

---