Pipes/piping pipe manufacturing

Tables 4—6 Ust ASTM methods used for the characterization of PB and PMP. A number of specialized methods were developed for testing particular articles manufactured from polyolefins several of these determine the performance of PB and PMP film, including the measurement of the film s dart impact strength and tear strength. Dart impact strength is measured by dropping a heavy dart with a round tip on a stretched film. Tear resistance, which reflects the film s resistance to tear propagation, is measured with the Ehnendorf tear tester. Two values for the tear strength are usually reported, one in the machine dkection of the film and the other in the transverse dkection. Pipes manufactured from PB are tested by pressurizing them internally with water the time-to-burst failure is determined at various temperatures (46). The standard test method for haze and luminous transmittance (ASTM D1003) is used for the measurement of PMP optical characteristics.

Shipments of concrete pipe in 1990 had a value of > 1.6 billion dollars. Much of this piping was for storm and sanitary sewers, culverts, and irrigation piping. Pressure piping sales were close to 300 million. There are a large number of manufacturers of concrete pipe since much of the pipe is produced reasonably close to the point of use. 

As with pipe, siding manufacturing is highly optimized for efficient production at high rates and minimal costs. Siding uses powder compounds, twin-screw extmders, and vacuum sizing/cooling. 

NOTE Consult pipe manufacturer for recommended hanger spacing for the specific RTR pipe being used. Tabulated values are based on a specific gravity of 1.25 for the contents of the pipe. To convert feet to meters, multiply by 0.3048. 

Examination and Inspection The code differentiates between examination and inspection. Examination applies to quality-control functions performed by personnel of the piping manufacturer, fabricator, or erector. Inspection applies to fiinctions performed for the owner by the authorized inspector. 

The C values for different types of resistances are available in hydraulics textbooks and also from the literature of pipe and valve manufacturers. 

Do not grossly oversize compressor piping. Compressor manufacturers generally recommend gas velocities in the... 

The major portion of drill string is composed of drill pipe. The drill pipe is manufactured by the seamless process. According to API Specification 5A (Thirty-fifth Edition, March 1981), seamless pipe is defined as a wrought steel tabular product made without a welded seam. It is manufactured by hot working steel or, if necessary, by subsequently cold finishing the hot worked tabular product to produce the desired shape, dimensions and properties. 

Geometrical and mechanical properties of heavy-weight drill pipe (Hevi-Wate ) manufactured by Drilco are given in Table 4-90. 

The resistance of titanium in nitric acid is good at most concentrations and at temperatures up to boiling . Thus tubular heat exchangers are used in ammonium nitrate production for preheating the acid prior to its introduction into the reactor via titanium sparge pipes. In explosives manufacture, concentrated nitric acid is cooled in titanium coils and titanium tanks are... 

Equipment manufacturers also work to standards to produce standardised designs and size ranges for commonly used items such as electric motors, pumps, pipes and pipe fittings. They will conform to national standards, where they exist, or to those issued by trade associations. It is clearly more economic to produce a limited range of standard sizes than to have to treat each order as a special job. 

Metal industries use substantial quantities of water in processes such as metal finishing and galvanized pipe manufacturing in order to produce corrosion-resistant products. Effluent wastewaters... 

TREATMENT OF WASTEWATER FROM ACID PICKLING TANKS IN A GALVANIZED PIPE MANUFACTURING FACTORY USING SULFURIC ACID... 

This stainless steel pipes and fittings manufacturing plant is located in the United States and produces stainless steel pipes of various diameters and lengths and custom-made pipe fittings.13 It operates over 6240 h/yr to produce nearly 30 million pounds of pipe annually. 

The initial evaluation showed that utilizing fiber-reinforced polymer (FRP) for pipelines is a feasible alternative to steel pipelines with regard to performance and cost [35]. From the cost analysis, an FRP pipe is quite attractive, especially in the regional or distributed service. Currently, spoolable piping manufacturers could install a composite pipeline for serving a 100,000 population for a cost of 250,000-500,000/mi. (does not include the cost for right-of-way), which is well below the DOE s capital cost target in 2017 of 800,000/mi. [35]. From this estimate and cost analyses, it is seen that FRP pipe economics is very attractive, especially for the distribution service. 

Pipe Products Manufactured with Fluorination Technology... 

---