Phenol, methylation properties

Phenol methylation to 2,6-xylenol has been widely studied for the past few deeades owing to the room for improvisation from the viewpoint of product selectivity. Generally during phenol methylation to 2,6-xylenol, occurs via sequential methylation of phenol to o-cresol to 2,6-xylenol, various reaction parameters mediate the selectivity between the two. For instance, when the reaetants stoichiometry of methanol to phenol molar ratio > 2, and significant residence time of o-cresol may favor 2,6-xylenol selectivity. However, excess methanol is often used, sinee some amount of methanol tend to undergo oxidation into various reformate produets [71] under vapor phase condition. Similarly, reaction temperature, catalyst acid-base property, and space velocity of the reaetant are the parameters that govern the selectivity to 2,6-xylenol. 

Chem. Descrip. POE nonyl phenol methyl ether Uses Surfactant Properties Wh. to pale yel. solid G-4884 [Croda Inc]... 

Heteroatom functionalized terpene resins are also utilized in hot melt adhesive and ink appHcations. Diels-Alder reaction of terpenic dienes or trienes with acrylates, methacrylates, or other a, P-unsaturated esters of polyhydric alcohols has been shown to yield resins with superior pressure sensitive adhesive properties relative to petroleum and unmodified polyterpene resins (107). Limonene—phenol resins, produced by the BF etherate-catalyzed condensation of 1.4—2.0 moles of limonene with 1.0 mole of phenol have been shown to impart improved tack, elongation, and tensile strength to ethylene—vinyl acetate and ethylene—methyl acrylate-based hot melt adhesive systems (108). Terpene polyol ethers have been shown to be particularly effective tackifiers in pressure sensitive adhesive appHcations (109). 

Nitrile rubber/phenolic resin blends. Blends of equal parts by weight of a nitrile rubber and a phenolic resin in methyl ethyl ketone (at a 20-30 wt% total solids content) is suitable for many adhesive purposes. The more phenolic resin in the formulation, the greater the bond strength and brittleness of the NBR adhesive [67]. Table 10 shows the effect of phenolic resin on nitrile rubber properties. On the other hand, the higher the acrylonitrile content in the rubber. 

Many of the properties oj -hydroxypyridines are typical of phenols. It was long assumed that they existed exclusively in the hydroxy form, and early physical measurements seemed to confirm this. For example, the ultraviolet spectrum of a methanolic solution of 3-hydroxypyridine is very similar to that of the 3-methoxy analog, and the value of the dipole moment of 3-hydroxypyridine obtained in dioxane indicates little, if any, zwitterion formation. However, it has now become clear that the hydroxy form is greatly predominant only in solvents of low dielectric constant. Comparison of the pK values of 3-hydroxypyridine with those of the alternative methylated forms indicated that the two tautomeric forms are of comparable stability in aqueous solution (Table II), and this was confirmed using ultraviolet spectroscopy. The ratios calculated from the ultraviolet spectral data are in good agreement with those de-... 

The purpose of this work was to increase the A3 selectivity at low conversion through a catalyst modification. Previous studies of phenol alkylation with methanol (the analogue reaction) over oxides and zeolites showed that the reaction is sensitive to acidic and basic properties of the catalysts [3-5]. It is the aim of this study to understand the dependence of catalyst structure and acidity on activity and selectivity in gas phase methylation of catechol. Different cations such as Li, K, Mg, Ca, B, incorporated into y-Al203 can markedly modify the polarisation of the lattice and consequently influence the acidic and basic properties of the surface [5-8] which control the mechanism of this reaction. 

Mg/Me (Me=Al, Fe) mixed oxides prepared from hydrotalcite precursors were compared in the gas-phase m-cresol methylation in order to find out a relationship between catalytic activity and physico-chemical properties. It was found that the regio-selectivity in the methylation is considerably affected by the surface acid-basic properties of the catalysts. The co-existence of Lewis acid sites and basic sites leads to an enhancement of the selectivity to the product of ortho-C-alkylation with respect to the sole presence of basic sites. This derives from the combination of two effects, (i) The H+-abstraction properties of the basic site lead to the generation of the phenolate anion, (ii) The coordinative properties of Lewis acid sites, through their interaction with the aromatic ring, make the mesomeric effect less efficient, with predominance of the inductive effect of the -O species in directing the regio-selectivity of the C-methylation into the ortho position. 

The final coal product in the MeOH/KOH experiments was 20%-25% soluble in the methanol. When the methanol was removed, the resultant product was a room temperature liquid with the properties described in Table V. Apparently the polymethylphenol fraction is formed by the cleavage of phenolic ethers and subsequent methyla-tion by the CO that is present in the reaction mixture as a result of methanol decomposition. The methylation reaction has been observed before for similar systems (3). 

The samples investigated initially were commercial high pressure low density, linear low density and high density polyethylenes and had properties given in Table 1. Solutions of these polymers were prepared in concentrations of 0.8 to 3.5 g/1 by dissolving the pol5rmer over a time period of two hours in an oven maintained at 145°C. To avoid degradation 0.05% 4,4 -thiobis(3-methyl-6-tert-butyl phenol) was used as an antioxidant in the solutions. 

There are important modifications of alkyds that help in specific applications. Phenolics can be added to improve film hardness and water resistance, but these confer increased yellowing tendencies on the final coating. Silicones impart heat resistance and exterior durability. Styrene increases the drying speed. Methyl methacrylate when added gives faster drying properties and improves the color and durability of the coating. 

---