Passivators examples

For example,copper has relatively good corrosion resistance under non-oxidizing conditions. It can be alloyed with zinc to yield a stronger material (brass), but with lowered corrosion resistance. Flowever, by alloying copper with a passivating metal such as nickel, both mechanical and corrosion properties are improved. Another important alloy is steel, which is an alloy between iron (>50%) and other alloying elements such as carbon. 

The protective quality of the passive film is detennined by the ion transfer tlirough the film as well as the stability of the film with respect to dissolution. The dissolution of passive oxide films can occur either chemically or electrochemically. The latter case takes place if an oxidized or reduced component of the passive film is more soluble in the electrolyte than the original component. An example of this is the oxidative dissolution of CrjO ... 

This example illustrates that exact infonnation on the chemistry and stmcture of the passive film is necessary to clarify the mechanisms relevant to stability and protectiveness of passive films. 

The passive state of a metal can, under certain circumstances, be prone to localized instabilities. Most investigated is the case of localized dissolution events on oxide-passivated surfaces [51, 106, 107, 108, 109, 110, ill, 112, 113, 114, 115, 116, 117 and 118]. The essence of localized corrosion is that distinct anodic sites on the surface can be identified where the metal oxidation reaction (e.g. Fe —> Fe + 2e ) dominates, surrounded by a cathodic zone where the reduction reaction takes place (e.g. 2Fi + 2e —> Fi2). The result is the fonnation of an active pit in the metal, an example of which is illustrated in figure C2.8.6(a) and (b). 

Strong oxidising acids, for example hot concentrated sulphuric acid and nitric acid, attack finely divided boron to give boric acid H3CO3. The metallic elements behave much as expected, the metal being oxidised whilst the acid is reduced. Bulk aluminium, however, is rendered passive by both dilute and concentrated nitric acid and no action occurs the passivity is due to the formation of an impervious oxide layer. Finely divided aluminium does dissolve slowly when heated in concentrated nitric acid. 

Sometimes the formation of oxide films on the metal surface binders efficient ECM, and leads to poor surface finish. Eor example, the ECM of titanium is rendered difficult in chloride and nitrate electrolytes because the oxide film formed is so passive. Even when higher (eg, ca 50 V) voltage is apphed, to break the oxide film, its dismption is so nonuniform that deep grain boundary attack of the metal surface occurs. 

Precipita.tingInhibitors. As discussed earlier, the localized pH at the cathode of the corrosion cell is elevated due to the generation of hydroxide ions. Precipitating inhibitors form complexes that are insoluble at this high pH (1—2 pH units above bulk water), but whose deposition can be controlled at the bulk water pH (typically 7—9 pH). A good example is zinc, which can precipitate as hydroxide, carbonate, or phosphate. Calcium carbonate and calcium orthophosphate are also precipitating inhibitors. Orthophosphate thus exhibits a dual mechanism, acting as both an anodic passivator and a cathodic precipitator. 

Passive transdermal dehvery systems on the market tend to be either matrix or membrane controUed. In matrix devices, the stmctural and molecular characteristics of the dmg-polymer matrix determine dmg release. Examples of polymer matrix-controUed diffusional systems for angina prophylaxis include Nitro-Dur and Nitrodisc, which provide transdermal dehvery of nitroglycerin [55-63-0], and Erandol, a tape that releases isosorbide dinitrate [87-33-2]. Matrix diffusional systems have been used for dehvering dmgs with a wide therapeutic index. 

The stainless steels contain appreciable amounts of Cr, Ni, or both. The straight chrome steels, types 410, 416, and 430, contain about 12, 13, and 16 wt % Cr respectively. The chrome—nickel steels include type 301 (18 wt % Cr and 9 wt % Ni), type 304 (19 wt % Cr and 10 wt % Ni), and type 316 (19 wt % Cr and 12 wt % Ni). Additionally, type 316 contains 2—3 wt % Mo which gready improves resistance to crevice corrosion in seawater as well as general corrosion resistance. AH of the stainless steels offer exceptional improvement in atmospheric conditions. The corrosion resistance results from the formation of a passive film and, for this reason, these materials are susceptible to pitting corrosion and to crevice corrosion. For example, type 304 stainless has very good resistance to moving seawater but does pit in stagnant seawater. 

Anodic Inhibitors. Passivating or anodic inhibitors produce a large positive shift in the corrosion potential of a metal. There are two classes of anodic inhibitors which are used for metals and alloys where the anodic shift in potential promotes passivation, ie, anodic protection. The fkst class includes oxidking anions that can passivate a metal in the absence of oxygen. Chromate is a classical example of an oxidking anodic inhibitor for the passivation of steels. 

The second class of anodic inhibitors contains ions which need oxygen to passivate a metal. Tungstate and molybdate, for example, requke the presence of oxygen to passivate a steel. The concentration of the anodic inhibitor is critical for corrosion protection. Insufficient concentrations can lead to pitting corrosion or an increase in the corrosion rate. The use of anodic inhibitors is more difficult at higher salt concentrations, higher temperatures, lower pH values, and in some cases, at lower oxygen concentrations (37). 

Electroforrning is the production or reproduction of articles by electro deposition upon a mandrel or mold that is subsequendy separated from the deposit. The separated electro deposit becomes the manufactured article. Of all the metals, copper and nickel are most widely used in electroforming. Mandrels are of two types permanent or expendable. Permanent mandrels are treated in a variety of ways to passivate the surface so that the deposit has very Httie or no adhesion to the mandrel, and separation is easily accompHshed without damaging the mandrel. Expendable mandrels are used where the shape of the electroform would prohibit removal of the mandrel without damage. Low melting alloys, metals that can be chemically dissolved without attack on the electroform, plastics that can be dissolved in solvents, ate typical examples. 

For example, chloride and duoride ions, even in trace amounts (ppm), could cause the dissolution of aluminum metallization of complimentary metal oxide semiconductor (CMOS) devices. CMOS is likely to be the trend of VLSI technology and sodium chloride is a common contaminant. The protection of these devices from the effects of these mobile ions is an absolute requirement. The use of an ultrahigh purity encapsulant to encapsulate the passivated IC is the answer to some mobile ion contaminant problems. 

Films Once corrosion has started, its further progress very often is controlled by the nature of films, such as passive films, that may form or accumulate on the metallic surface. The classical example is the thin oxide tilm that forms on stainless steels. 

Impurities in a corrodent can be good or bad from a corrosion standpoint. An impurity in a stream may act as an inhibitor and actually retard corrosion. However, if this impurity is removed by some process change or improvement, a marked rise in corrosion rates can result. Other impurities, of course, can have very deleterious effec ts on materials. The chloride ion is a good example small amounts of chlorides in a process stream can break down the passive oxide film on stainless steels. The effects of impurities are varied and complex. One must be aware of what they are, how much is present, and where they come from before attempting to recommena a particular material of construction. 

Use and Uimitations of Electrochemical Techniques A major caution must be noted as to the general, indiscriminate use of all electrochemical tests, especially the use of AC and EIS test techniques, for the study of corrosion systems. AC and EIS techniques are apphcable for the evaluation of very thin films or deposits that are uniform, constant, and stable—for example, thin-film protective coatings. Sometimes, researchers do not recognize the dynamic nature of some passive films, corrosion produc ts, or deposits from other sources nor do they even consider the possibility of a change in the surface conditions during the course of their experiment. As an example, it is note-... 

There are no films or protective surface films on active metals, e.g., mild steel in acid or saline solutions. Passive metals are protected by dense, less readily soluble surface films (see Section 2.3.1.2). These include, for example, high-alloy Cr steels and NiCr alloys as well as A1 and Ti in neutral solutions. Selective corrosion of alloys is largely a result of local concentration differences of alloying elements which are important for corrosion resistance e.g., Cr [4],... 

---