Natural reformation

Simple conventional refining is based essentially on atmospheric distillation. The residue from the distillation constitutes heavy fuel, the quantity and qualities of which are mainly determined by the crude feedstock available without many ways to improve it. Manufacture of products like asphalt and lubricant bases requires supplementary operations, in particular separation operations and is possible only with a relatively narrow selection of crudes (crudes for lube oils, crudes for asphalts). The distillates are not normally directly usable processing must be done to improve them, either mild treatment such as hydrodesulfurization of middle distillates at low pressure, or deep treatment usually with partial conversion such as catalytic reforming. The conventional refinery thereby has rather limited flexibility and makes products the quality of which is closely linked to the nature of the crude oil used. 

Natural gas is by far the preferred source of hydrogen. It has been cheap, and its use is more energy efficient than that of other hydrocarbons. The reforming process that is used to produce hydrogen from natural gas is highly developed, environmental controls are simple, and the capital investment is lower than that for any other method. Comparisons of the total energy consumption (fuel and synthesis gas), based on advanced technologies, have been discussed elsewhere (102). 

Separation, combustion, pyrolysis, hydrogena-tion, anaerobic fermen-tation, aerobic fermen-tation, biophotolysis, partial oxidation, steam reforming, chemical hy-drolysis, enzyme hydrol-ysis, other chemical conversions, natural processes... 

In general, the proven technology to upgrade methane is via steam reforming to produce synthesis gas, CO + Such a gas mixture is clean and when converted to Hquids produces fuels substantially free of heteroatoms such as sulfur and nitrogen. Two commercial units utilizing the synthesis gas from natural gas technology in combination with novel downstream conversion processes have been commercialized. 

Coal gasification technology dates to the early nineteenth century but has been largely replaced by natural gas and oil. A more hydrogen-rich synthesis gas is produced at a lower capital investment. Steam reforming of natural gas is appHed widely on an iadustrial scale (9,10) and ia particular for the production of hydrogen (qv). 

Synthesis Gas Chemicals. Hydrocarbons are used to generate synthesis gas, a mixture of carbon monoxide and hydrogen, for conversion to other chemicals. The primary chemical made from synthesis gas is methanol, though acetic acid and acetic anhydride are also made by this route. Carbon monoxide (qv) is produced by partial oxidation of hydrocarbons or by the catalytic steam reforming of natural gas. About 96% of synthesis gas is made by steam reforming, followed by the water gas shift reaction to give the desired H2 /CO ratio. 

Cyclic Hydrocarbons. The cyclic hydrocarbon intermediates are derived principally from petroleum and natural gas, though small amounts are derived from coal. Most cycHc intermediates are used in the manufacture of more advanced synthetic organic chemicals and finished products such as dyes, medicinal chemicals, elastomers, pesticides, and plastics and resins. Table 6 details the production and sales of cycHc intermediates in 1991. Benzene (qv) is the largest volume aromatic compound used in the chemical industry. It is extracted from catalytic reformates in refineries, and is produced by the dealkylation of toluene (qv) (see also BTX Processing). 

Butanes are naturally occurring alkane hydrocarbons that are produced primarily in association with natural gas processing and certain refinery operations such as catalytic cracking and catalytic reforming. The term butanes includes the two stmctural isomers, / -butane [106-97-8] CH2CH2CH2CH2, and isobutane [79-28-9], (CH2)2CHCH2 (2-methylpropane). 

Butanes are recovered from raw natural gas and from petroleum refinery streams that result from catalytic cracking, catalytic reforming, and other refinery operations. The most common separation techniques are based on a vapor—Hquid, two-phase system by which Hquid butane is recovered from the feed gas. 

Steam Reforming. In steam reforming, light hydrocarbon feeds ranging from natural gas to straight mn naphthas are converted to synthesis gas (H2, CO, CO2) by reaction with steam (qv) over a catalyst in a primary reformer furnace. This process is usually operated at 800—870°C and 2.17—2.86... 

Naphtha at one time was a more popular feed, and alkah-promoted catalysts were developed specifically for use with it. As of 1994 the price of naphtha in most Western countries is too high for a reformer feed, and natural gas represents the best economical feedstock. However, where natural gas is not available, propane, butane, or naphtha is preferentially selected over fuel oil or coal. 

Naphtha desulfurization is conducted in the vapor phase as described for natural gas. Raw naphtha is preheated and vaporized in a separate furnace. If the sulfur content of the naphtha is very high, after Co—Mo hydrotreating, the naphtha is condensed, H2S is stripped out, and the residual H2S is adsorbed on ZnO. The primary reformer operates at conditions similar to those used with natural gas feed. The nickel catalyst, however, requires a promoter such as potassium in order to avoid carbon deposition at the practical levels of steam-to-carbon ratios of 3.5—5.0. Deposition of carbon from hydrocarbons cracking on the particles of the catalyst reduces the activity of the catalyst for the reforming and results in local uneven heating of the reformer tubes because the firing heat is not removed by the reforming reaction. 

Pkctro-Keforming The concept of using electricity to provide the endothermic heat of reforming has been proposed. Nuclear waste heat can be contained in high temperature helium gas which is brought into heat exchange with a natural gas feedstock (142). 

Higher range based on a 2.8 X 10 m /d steam reformer of natural gas at 1.90/kJ. Cost varies based on volume deflvered. 

High temperature steam reforming of natural gas accounts for 97% of the hydrogen used for ammonia synthesis in the United States. Hydrogen requirement for ammonia synthesis is about 336 m /t of ammonia produced for a typical 1000 t/d ammonia plant. The near-term demand for ammonia remains stagnant. Methanol production requires 560 m of hydrogen for each ton produced, based on a 2500-t/d methanol plant. Methanol demand is expected to increase in response to an increased use of the fuel—oxygenate methyl /-butyl ether (MTBE). 

Na.tura.1 Ga.s Reforma.tion. In the United States, most hydrogen is presently produced by natural gas reformation or methane—steam reforming. In this process, methane mixed with steam is typically passed over a nickel oxide catalyst at an elevated temperature. The reforming reaction is... 

---