Nation, Carry

The national organizations are often relayed into each profession by a body created and financed by this profession and which undertakes all or part of the work in preparing the standards. In the petroleum industry, this role is carried out in France by the BNPet (Bureau de Normalisation du Petrole) and in Germany by the FAM (Fachausschuss Mineralol-und Brennstoffnormung), in the United Kingdom by the IP (Institute of Petroleum), and in the USA by the ASTM (American Society for Testing and Materials). In the first two cases, the standards are published only by the national organizations (AFNOR and DIN respectively), while the IP and the ASTM also publish their own documents, only some of which are adopted by the BSI and ANSI, respectively. 

The research activity here presented has been carried out at the N.D.T. laboratory of l.S.P.E.S.L. (National Institute for Occupational Safety and Prevention) and it is aimed at the set up of the Stress Pattern Analysis by Measuring Thermal Emission technique [I] applied to pressure vessels. Basically, the SPATE system detects the infrared flux emitted from points resulting from the minute temperature changes in a cyclically stressed structure or component. 

Where conformity assessment involves intervention of third party, that task is normally carried out by the notified body. The pressure equipment directive enables in addition the national authorities to authorise in their territory user inspectorates for the carrying out of conformity assessment procedures which relate to product verification. These inspectorates shall act exclusively on behalf of the group of which they are part. The placing on the market and putting into service of equipment which has undergone such assessment is however limited to the territory of the authorising Member State and to those Member States which have also proceeded to such authorisation. The equipment concerned shall therefore not bear the CE-marking. 

The National system of accreditation gives much attention to the training and qualification of NDT personnel. Significant subjective component, such as training and qualification of personnel, is present in NDT implementation and assessment of its results, thus all specialists carrying out NDT must be certified in compliance with CTBEH 473. 

In recent years, the three-level system of NDT experts certification, which corresponds to the EN 473, is being introduced m Ukraine The unified Rules of NDT Experts Certification will be introduced in the near future. This work is headed by the State Committee of Ukraine on Labour Safety), and with the aim of the most expedient transition to EN 473, the National Certification Committee of Ukraine on NDT was established by the initiative of US NDT TD. The Committee has the tasks of preparing the programs, procedures, questionnaires for carrying out the certification. It is a non-profit organisation which is in charge of the methodological issues of certification m the US NDT TD. 

Soil. Composting of soils contaminated by high explosives is being carried out at the Umatilla Army Depot near Hermiston, Oregon (70). Soil from munitions washout lagoons is being treated iadoors ia compost rows of 2,000 m, and the estimated cost is less than one-third the estimated cost of iaciaeration. If this is successful, there are 30 similar sites on the National Priority List that could be treated ia a similar way. 

The OLEFLEX process uses multiple side-by-side, radial flow, moving-bed reactors connected in series. The heat of reaction is suppHed by preheated feed and interstage heaters. The gas-phase reaction is carried out over a catalyst, platinum supported over alumina, under very near isothermal conditions. The first commercial installation of this technology, having an annual capacity of 100,000 t, was made in 1990 by the National Petrochemical Corporation in Thailand. A second unit, at 245,000 t capacity, has been built in South Korea by the ISU Chemical Company (70). 

Research on an hCG vaccine has been conducted over the past 15 years. WHO has conducted a phase I clinical study in AustraUa, using a vaccine based on a synthetic C-terminal peptide (109—141) of P-hCG conjugated to Diptheria Toxoid (CTP-DT), that showed potentially effective contraceptive levels of antibodies were produced in vaccinated women without any adverse side effects. Phase II clinical studies are under consideration to determine if the immune response, raised to its prototype anti-hCG vaccine, is capable of preventing pregnancy in fertile women volunteers (115). While research on the C-terminal peptide from the P-subunit of hCG has been carried out under the auspices of WHO, research supported by the Population Council and the National Institutes of Health has involved two alternative vaccine candidates (109,116,118). 

In 1974, the Harmonized Monitoring Programme was set up by the Department of the Environment (DoE). The objective was to provide a network of sites at the lower end of catchments, where water quality data could be collected and analysed in a nationally consistent manner, allowing the loads of materials carried through river catchments into estuaries to be estimated and long-term trends in river quality to be assessed. The complete list of substances to be monitored is diverse and specifies about 115 substances. The pesticides aldrin, dieldrin, y-HCH, heptachlor, p,p -DDT and p,p -DDE are included. Figures 1 and 2 show the downward trend of y-HCH and dieldrin over the past 20 years at the Harmonized Monitoring Sites. This confirms that reductions in environmental concentrations have been achieved, particularly over the past 10 years. 

The product specification should provide all necessary processing requirements that need to be implemented when carrying out particular processes however, some of the requirements may need to be defined in separate process specifications which are invoked by reference. You may need to develop your own process specifications, but there are many national standards that may suit your needs and they come with the added benefit that they have been proven to work. The quality plan or procedures should not contain any further product requirements but may provide the verification methods to be employed, the precautions to be observed and the recording requirements to be met. You need to identify in your production plans each of these documents at the stage at which they should be applied, otherwise there is the possibility that they may be overlooked. 

---