Naphtha sulfur

Note Accdg to Marshall 1 (Ref 11, p 12), Col Hime in his book listed here as Ref 4, came to the conclusion that, besides naphtha, sulfur and pitch, there must have been quicklime in mixture, which on coming in contact with sea water turned into slaked lime whilst raising the temperature to the point of ignition of sulfur. Greek Fire mixture was discharged from tubes or siphons located in the bows of the ships, against the... 

Benzene [71-43-2] toluene [108-88-3] xylene [1330-20-7] and solvent naphtha are separated from the light oil. Benzene (qv), toluene (qv), and xylene are useful as solvents and chemical intermediates (see Xylenes and ethylbenzene). The cmde light oil is approximately 60—70% ben2ene, 12—16% toluene, 4—8% xylenes, 9—16% other hydrocarbons, and about 1% sulfur compounds (5) (see BTX processing). 

Properties. The properties of naphtha, gas od, and H-od products from an H-coal operation are given in Table 7. These analyses are for Hquids produced from the syncmde operating mode. Whereas these Hquids are very low in sulfur compared with typical petroleum fractions, they are high in oxygen and nitrogen levels. No residual od products (bp > 540° C) are formed. 

Table 8 shows that the naphthas produced by the EDS process have higher concentrations of cycloparaffins and phenols than do petroleum-derived naphthas, whereas the normal paraffins are present in much lower concentrations. The sulfur and nitrogen concentrations in coal naphthas are high compared to those in petroleum naphthas. 

Naphtha desulfurization is conducted in the vapor phase as described for natural gas. Raw naphtha is preheated and vaporized in a separate furnace. If the sulfur content of the naphtha is very high, after Co—Mo hydrotreating, the naphtha is condensed, H2S is stripped out, and the residual H2S is adsorbed on ZnO. The primary reformer operates at conditions similar to those used with natural gas feed. The nickel catalyst, however, requires a promoter such as potassium in order to avoid carbon deposition at the practical levels of steam-to-carbon ratios of 3.5—5.0. Deposition of carbon from hydrocarbons cracking on the particles of the catalyst reduces the activity of the catalyst for the reforming and results in local uneven heating of the reformer tubes because the firing heat is not removed by the reforming reaction. 

The 3 -heterocychcs ia the mid-distiUate range are primarily the thiacyclanes, ben2othiophenes, and diben2othiophenes. There are lesser amounts of dialkyl—, diaryl—, and aryl—alkyl sulfides (29). Alkylthiophenes are scarce or absent, but some evidence exists for ben2thiacyclanes (Fig. 6). As for the naphtha fractions, these sulfur species account for a minimal fraction of the total sulfur ia the cmde. 

Solvent Treatment. Solvent processes can be divided into two main categories, solvent extraction and solvent dewaxing. The solvent used in the extraction processes include propane and cresyHc acid, 2,2 -dichlorodiethyl ether, phenol (qv), furfural, sulfur dioxide, benzene, and nitrobenzene. In the dewaxing process (28), the principal solvents are benzene, methyl ethyl ketone, methyl isobutyl ketone, propane, petroleum naphtha, ethylene dichloride, methylene chloride, sulfur dioxide, and iV-methylpyrroHdinone. 

Solvents used for dewaxing are naphtha, propane, sulfur dioxide, acetone—benzene, trichloroethylene, ethylenedichloride—benzene (Barisol), methyl ethyl ketone—benzene (benzol), methyl -butyl ketone, and methyl / -propyl ketone. Other solvents in commercial use for dewaxing include /V-methylpyrrolidinone, MEK—MIBK (methyl isobutyl ketone), dichloroethane—methylene dichloride, and propfyene—acetone. 

Steam Reforming Processes. In the steam reforming process, light hydrocarbon feedstocks (qv), such as natural gas, Hquefied petroleum gas, and naphtha, or in some cases heavier distillate oils are purified of sulfur compounds (see Sulfurremoval and recovery). These then react with steam in the presence of a nickel-containing catalyst to produce a mixture of hydrogen, methane, and carbon oxides. Essentially total decomposition of compounds containing more than one carbon atom per molecule is obtained (see Ammonia Hydrogen Petroleum). 

First, the tar acids were removed from the naphtha fractions of light oils and, in the case of CVR tars, carboHc oil. The oils were then mixed with 25—35% sulfuric acid. After separation of the sulfates, the aqueous solution was diluted with water and the resinous material skimmed off. The diluted sulfate solution was boiled to expel any neutral oils, dried by the addition of soHd caustic soda or a2eotropically with ben2ene, and fractionated to yield pyridine, 2-methylpyridine (a-picoline), and a fraction referred to as 90/140 bases, which consisted mainly of 3- and 4-methylpyridines and 2,6-dimethylpyridine (2,6-lutidine). Higher boiling fractions were termed 90/160 and 90/180 bases because 90% of the product distilled at 160 and 180°C, respectively. 

Compounds considered carcinogenic that may be present in air emissions include benzene, butadiene, 1,2-dichloroethane, and vinyl chloride. A typical naphtha cracker at a petrochemical complex may release annually about 2,500 metric tons of alkenes, such as propylenes and ethylene, in producing 500,000 metric tons of ethylene. Boilers, process heaters, flares, and other process equipment (which in some cases may include catalyst regenerators) are responsible for the emission of PM (particulate matter), carbon monoxide, nitrogen oxides (200 tpy), based on 500,000 tpy of ethylene capacity, and sulfur oxides (600 tpy). 

Chemical and Other Specialty Manufacture A wide variety of products may be derived from petroleum feed stocks, including such diverse materials as alcohols, butyl rubber, sulfur, additives, and resins. Other specialties such as solvent naphthas, white oils, Isopars, Varsol, may also be produced. As indicated previously the respective chemical affiliate usually has responsibility for products broadly classified as petrochemicals. 

---