Mossbauer spectroscopy technique

Figure 2 Iron and cobalt phases detected by XRD, XPS and Mossbauer spectroscopy techniques as a function of the Co/Co+Fe atomic ratio in supported and unsupported catalysts.

VARIOUS MOSSBAUER SPECTROSCOPY TECHNIQUES IN STUDY OF APPLICATIONS RELATED TO NANOCRYSTALLINE IRON OXIDES... 

Fe Mossbauer spectroscopy technique has been widely applied to study the compounds of iron in high oxidation states. Various reviews have been written to utilize this technique [19,21,23,24,93,94]. Herein, we describe mostly the work... 

New experiments on Fe in Si with the in-beam Mossbauer spectroscopy technique were performed at the Hahn-Meitner institute in Berlin. The technique is outlined in Sect. 6.3. The results of these Coulomb excitation recoil implantation studies [26] confirmed this picture and led to an unambiguous identification of... 

To overcome the above mentioned difficulties in the studies of the fast diffusion in metals, several research projects were designed and performed in 1980s for about 10 years using the in-beam Mossbauer spectroscopy technique combining... 

The spectroscopic techniques that have been most frequently used to investigate biomolecular dynamics are those that are commonly available in laboratories, such as nuclear magnetic resonance (NMR), fluorescence, and Mossbauer spectroscopy. In a later chapter the use of NMR, a powerful probe of local motions in macromolecules, is described. Here we examine scattering of X-ray and neutron radiation. Neutrons and X-rays share the property of being found in expensive sources not commonly available in the laboratory. Neutrons are produced by a nuclear reactor or spallation source. X-ray experiments are routinely performed using intense synclirotron radiation, although in favorable cases laboratory sources may also be used. 

Electrobalances suitable for thermogravimetry are readily adapted for measurements of magnetic susceptibility [333—336] by the Faraday method, with or without variable temperature [337] and data processing facilities [338]. This approach has been particularly valuable in determinations of the changes in oxidation states which occur during the decompositions of iron, cobalt and chromium oxides and hydroxides [339] and during the formation of ferrites [340]. The method requires higher concentrations of ions than those needed in Mossbauer spectroscopy, but the apparatus, techniques and interpretation of observations are often simpler. 

The great advantage of Mossbauer spectroscopy is that it can be applied in situ. The major limitation of the technique is that it can only be applied to a couple of elements, among which iron and tin are the easiest to study. 

The second approach is to study real catalysts with in situ techniques such as infrared and Mossbauer spectroscopy, EXAFS and XRD, under reaction conditions, or, as is more often done, under a controlled environment after quenching of the reaction. The in situ techniques, however, are not sufficiently surface specific to yield the desired atom-by-atom characterization of the surface. At best they determine the composition of the particles. 

Of special Interest as O2 reduction electrocatalysts are the transition metal macrocycles In the form of layers adsorptlvely attached, chemically bonded or simply physically deposited on an electrode substrate Some of these complexes catalyze the 4-electron reduction of O2 to H2O or 0H while others catalyze principally the 2-electron reduction to the peroxide and/or the peroxide elimination reactions. Various situ spectroscopic techniques have been used to examine the state of these transition metal macrocycle layers on carbon, graphite and metal substrates under various electrochemical conditions. These techniques have Included (a) visible reflectance spectroscopy (b) laser Raman spectroscopy, utilizing surface enhanced Raman scattering and resonant Raman and (c) Mossbauer spectroscopy. This paper will focus on principally the cobalt and Iron phthalocyanlnes and porphyrins. 

In studies of superparamagnetic relaxation the blocking temperature is defined as the temperature at which the relaxation time equals the time scale of the experimental technique. Thus, the blocking temperature is not uniquely defined, but depends on the experimental technique that is used for the study of superparamagnetic relaxation. In Mossbauer spectroscopy studies of samples with a broad distribution of relaxation times, the average blocking temperature is commonly defined as the temperature where half of the spectral area is in a sextet and half of it is in a singlet or a doublet form. 

Conversion electron Mossbauer spectroscopy (CEMS) measurements with back scattering geometry have the merit that spectra can be obtained from a sample with much less isotope content compared with transmission measurements. Another merit is that a sample, deposited on a thick substrate, could be measured, and that because of the limited escape depth of the conversion electrons, depth-selective surface studies are possible. The CEMS technique was found to be best applicable to specimens of 10-100 pg Au cm, i.e., about two orders of magnitudes thinner than required for measurements in transmission mode [443]. This way (1) very thin films of gold alloys, as well as laser- and in beam-modified surfaces in the submicrometers range of depth [443], and (2) metallic gold precipitates in implanted MgO crystals [444] were investigated. 

Mossbauer spectroscopy is particularly suitable to study ST since (1) the spectral parameters associated with the HS and LS states of iron(II) clearly differ and (2) the time-scale of the technique ( 10 s) allows the detection of the separate spin states in the course of the transition. Typically, Mossbauer spectra of HS iron(II) show relatively high quadrupole splitting (AEq 2-3 mm s ) and isomer shift (3 1 mm s ), while for LS iron(II), these parameters are generally smaller (AEq < 1 mm s 3 < 0.5 mm s ). Among the early applications of Mossbauer spectroscopy to study ST phenomena in iron(II) complexes is the work of Dezsi et al. [7] on [Fe (phen)2(NCS)2] (phen = 1,10-phenanthroline) as a function of temperature (Fig. 8.2). The transition from the HS ( 12) state (quadrupole doublet of outer two lines with AEq 3 mm s ) to the LS CAi) state (quadrupole... 

Coordination compounds of dianionic dithiolene (S2C2 R2) and benzene-1,2-dithiolene (bdt = (S2C6H4) and their derivatives have been studied since the 1960s by Mossbauer spectroscopy [87] and other techniques. Nevertheless, many aspects of their electronic structure remained uncertain for a long time. The five-coordinate ferric complexes with two equatorial dithiolene ligands exhibit intermediate spin and show the Mossbauer parameters = 0.25-0.38 mm s and A q = 1.6-3.2 mm s For example, [Fe° mnt)2/ y] with two mnt ligands (=S2C2(CN)2) and an... 

Mossbauer spectroscopy is an analytical technique that, in archaeological ceramic studies, provides information on the condition and characteristics of the compounds of iron in pottery. Using the technique makes it possible to determine the relative amounts of the different (ferrous and ferric) ions of iron and hence to ascertain the firing conditions of the pottery at the time it was made. The technique involves irradiating a sample of pottery with gamma rays and then assessing the amount of radiation absorbed by the nuclei of the ions of iron within the pottery (Feathers et al. 1998 Bearat and Pradell 1997). 

Introduce instrumental techniques used in analysis of the bioinorganic systems I will lecture on (Chapter 3 Instrumental and Computer-Based Methods). Typically, these would be electron paramagnetic resonance (EPR) and Mossbauer spectroscopies not often covered in undergraduate instrumental analysis courses plus X-ray diffraction and NMR techniques used for structural analyses of metalloproteins and their small molecule model compounds. 

---