Monomers, polymerized

This monomer polymerizes faster ia 50% water than it does ia bulk (35), an abnormaHty iaconsistent with general polymerization kinetics. This may be due to a complex with water that activates the monomer it may also be related to the impurities ia the monomer (eg, acetaldehyde, 1-methyl pyrroHdone, and 2-pyrroHdone) that are difficult to remove and that would be diluted and partitioned ia a 50% aqueous media (see Vinyl polymers, A/-VINYLAMIDE POLYPffiRS). 

Wheieas the BPO—DMA ledox system works well for curing of unsaturated polyester blends, it is not a very effective system for initiating vinyl monomer polymerizations, and therefore it generally is not used in such appHcations (34). However, combinations of amines (eg, DMA) and acyl sulfonyl peroxides (eg, ACSP) are very effective initiator systems at 0°C for high conversion suspension polymerizations of vinyl chloride (35). BPO has also been used in combination with ferrous ammonium sulfate to initiate emulsion polymerizations of vinyl monomers via a redox reaction (36). 

Because high temperatures are required to decompose diaLkyl peroxides at useful rates, P-scission of the resulting alkoxy radicals is more rapid and more extensive than for most other peroxide types. When methyl radicals are produced from alkoxy radicals, the diaLkyl peroxide precursors are very good initiators for cross-linking, grafting, and degradation reactions. When higher alkyl radicals such as ethyl radicals are produced, the diaLkyl peroxides are useful in vinyl monomer polymerizations. 

Peioxydicaibonates are efficient polymerization initiators for most vinyl monomer polymerizations, especially for monomers such as acrylates, ethylene, and vinyl chloride. They are particularly good initiators for less reactive monomers such as those containing aHyl groups. They are also effective for curing of unsaturated polyester mol ding resins. 

The Smith-Ewart kinetics described assume homogeneous conditions within the particle. An alternative view, where monomer polymerizes only on the surface of the particle, has been put forth (35) and supported (36). The nature of the intraparticle reaction environment remains an important question. 

Without other alternatives, the carboxyalkyl radicals couple to form dibasic acids HOOC(CH)2 COOH. In addition, the carboxyalkyl radical can be used for other desired radical reactions, eg, hydrogen abstraction, vinyl monomer polymerization, addition of carbon monoxide, etc. The reactions of this radical with chloride and cyanide ions are used to produce amino acids and lactams employed in the manufacture of polyamides, eg, nylon. 

The first-order decomposition rates of alkyl peroxycarbamates are strongly influenced by stmcture, eg, electron-donating substituents on nitrogen increase the rate of decomposition, and some substituents increase sensitivity to induced decomposition (20). Alkyl peroxycarbamates have been used to initiate vinyl monomer polymerizations and to cure mbbers (244). They Hberate iodine quantitatively from hydriodic acid solutions. Decomposition products include carbon dioxide, hydrazo and azo compounds, amines, imines, and O-alkyUiydroxylarnines. Many peroxycarbamates are stable at ca 20°C but decompose rapidly and sometimes violently above 80°C (20,44). 

The main industrial use of alkyl peroxyesters is in the initiation of free-radical chain reactions, primarily for vinyl monomer polymerizations. Decomposition of unsymmetrical diperoxyesters, in which the two peroxyester functions decompose at different rates, results in the formation of polymers of enhanced molecular weights, presumably due to chain extension by sequential initiation (204). 

Etee-tadical reactions ate accompHshed using a variety of processes with different temperature requirements, eg, vinyl monomer polymerization and polymer modifications such as curing, cross-linking, and vis-breaking. Thus, the polymer industries ate offered many different, commercial, organic peroxides representing a broad range of decomposition temperatures, as shown in Table 17 (19,22,31). 

Photopolymerization reactions are widely used for printing and photoresist appHcations (55). Spectral sensitization of cationic polymerization has utilized electron transfer from heteroaromatics, ketones, or dyes to initiators like iodonium or sulfonium salts (60). However, sensitized free-radical polymerization has been the main technology of choice (55). Spectral sensitizers over the wavelength region 300—700 nm are effective. AcryUc monomer polymerization, for example, is sensitized by xanthene, thiazine, acridine, cyanine, and merocyanine dyes. The required free-radical formation via these dyes may be achieved by hydrogen atom-transfer, electron-transfer, or exciplex formation with other initiator components of the photopolymer system. 

Determine the worst-case gas mixture combustion charac teris-tics, system pressure, and permissible pressure drop across the arrester, to help select the most appropriate element design. Not only does element design impac t pressure drop, but the rate of blockage due to particle impact, liquid condensation, and chemical reaction (such as monomer polymerization) can make some designs impractical even if in-service and out-of-seivdce arresters are provided in parallel. 

Figure 14.13 Stmcture of G-actin. Two a/P-domains, (red and green) bind an ATP molecuie between them. Tbis ATP is hydrolyzed when the actin monomer polymerizes to F-actin.

The free radical initiators are more suitable for the monomers having electron-withdrawing substituents directed to the ethylene nucleus. The monomers having electron-supplying groups can be polymerized better with the ionic initiators. The water solubility of the monomer is another important consideration. Highly water-soluble (relatively polar) monomers are not suitable for the emulsion polymerization process since most of the monomer polymerizes within the continuous medium, The detailed emulsion polymerization procedures for various monomers, including styrene [59-64], butadiene [61,63,64], vinyl acetate [62,64], vinyl chloride [62,64,65], alkyl acrylates [61-63,65], alkyl methacrylates [62,64], chloroprene [63], and isoprene [61,63] are available in the literature. 

The departure of dependence of Rp on the concentration of CHP from 0.5 order might be ascribed to induction decomposition of ROOH type to form ROO- radical, which has very low activity to initiate monomer polymerization [40], but can combine with the propagation chain radical to form the primary radical termination. For the same reason, the order of concentration of TBH was also lower than 0.5 when the TBH-DMT system was used as the initiator in MMA bulk polymerization. But in the BPO-DMT initiation system as shown in Table... 

The azo initiator initially present therefore has to be classified as a transfer agent—it is able to combine monomers polymerized by different polymerization modes with each other. Three different modes of block copolymer synthesis via azo transfer agents can be distinguished ... 

Parent polyfthicnylene vinylene) has also been synthesized by an aldol precursor route [122]. In this method, 5-methyl-2-thiophenecarbaldehyde 76 is treated with a base and the monomer polymerizes yielding a precursor 77 which is soluble in water. Thermal treatment in an acidic solution at 80 nC yields the fully conjugated material. Alternatively, the solid polymer may be healed to 280 C to effect elimination of water. Fully conjugated material exhibits low conductivity (10 8 S cm"1) in its pristine stale. 

Vinyl monomers, polymerization of, 154 Vinyl polymerization, 172 Vinylidine, monomer polymerization of, 164... 

Quite naturally, novel techniques for manufacturing composite materials are in principal rare. The polymerization filling worked out at the Chemical Physics Institute of the USSR Academy of Sciences is an example of such techniques [49-51], The essence of the technique lies in that monomer polymerization takes place directly on the filler surface, i.e. a composite material is formed in the polymer forming stage which excludes the necessity of mixing constituents of a composite material. Practically, any material may be used as a filler the use of conducting fillers makes it possible to obtain a composite material having electrical conductance. The material thus obtained in the form of a powder can be processed by traditional methods, with polymers of many types (polyolefins, polyvinyl chloride, elastomers, etc.) used as a matrix. 

Stages Basic Chemical Monomers Polymerization Compounding Processing Fabricating Finishing... 

A number of recent papers have explored enzyme-mediated polymerization. Monomers polymerized include MMA, S, AM and derivatives. The area has been reviewed by Singh and Kaplan222 and Gross et al. n... 

The outcome of the polymerization depends strongly on the particular monomer. Polymerizations of S, MMA, MA, VAc and some derivatives have been reported. Studies on model compounds indicate that the primary or secondary dithiocarbamatc end groups arc much less susceptible to photodissociation than benzyl or tertiary derivatives. 

Uses. There are about forty to fifty organic peroxides commercially available in more than seventy formulations designed for specific applications which include (1) initiators for vinyl monomer polymerizations, and copolymerizations of monomers such as vinyl chloride, ethylene, styrene, vinyl acetate, acrylics, fluoroolefms and buta-dienestyrene (2) curing agents for thermoset polyesters, styrenated alkyds and oils, silicone rubbers and poly allyl diglycol carbonates ... 

Polymerization,- Violent. Violent monomer polymerization has caused a number of serious explns. Present in Table 1 below is a summary of data pertinent to the causation of these explns, extracted from the ref. The monomers listed may be found under appropriate entry titles thruout the Encycl Ref M. Harmon J. King, A Review of Violent Monomer Polymerization A Selected literature Survey , Report No USCG-D-159-75, Contract DOT-CG-51, 765-A, Operations Research, Inc, Silver Spring (1974)... 

Assuming that no intramolecular or side reactions take place and that all groups are equireactive, the polydispersity index, 7P, of hyperbranched polymers obtained by step-growth polymerization of ABX monomers is given by Eq. (2.2), where pA is die conversion in A groups.196 Note that the classical Flory relationship DPn = 1/(1 — pa) holds for ABX monomer polymerizations ... 

Biomedical applications, 27 Bionolle, 28, 42, 43 Biopol polyesters, 28, 41 Bioresorbable polyesters, 27 synthesis of, 99-101 Biphenol-based copolymers, 356 Bis(aryloxy) monomers, polymerization of, 347... 

Cyclic voltammetry is most commonly used to investigate the polymerization of a new monomer. Polymerization and film deposition are characterized by increasing peak currents for oxidation of the monomer on successive cycles, and the development of redox waves for the polymer at potentials below the onset of monomer oxidation. A nucleation loop, in which the current on the reverse scan is higher than on the corresponding forward scan, is commonly observed during the first cycle.56,57 These features are all illustrated in Fig. 3 for the polymerization of a substituted pyrrole.58... 

Hall and his co-workers43 synthesized several 2-oxabicyclo[2.1.1 ]hexan-3-ones from the corresponding 3-chlorocyclobutanecarboxylic acids. These monomers polymerized readily when heated with a variety of basic or acidic initiators. Some of the results of the polymerization are listed in Table 2. 

Example 4.3 Suppose a pure monomer polymerizes in a CSTR with pseudo-first-order kinetics. The monomer and pol5Tner have different... 

Vinyl copolymers contain mers from two or more vinyl monomers. Most common are random copolymers that are formed when the monomers polymerize simultaneously. They can be made by most polymerization mechanisms. Block copolymers are formed by reacting one monomer to completion and then replacing it with a different monomer that continues to add to the same polymer chain. The polymerization of a diblock copolymer stops at this point. Triblock and multiblock polymers continue the polymerization with additional monomer depletion and replenishment steps. The polymer chain must retain its ability to grow throughout the process. This is possible for a few polymerization mechanisms that give living polymers. 

---