Mechanical properties stress corrosion

The Institute has many-year experience of investigations and developments in the field of NDT. These are, mainly, developments which allowed creation of a series of eddy current flaw detectors for various applications. The Institute has traditionally studied the physico-mechanical properties of materials, their stressed-strained state, fracture mechanics and developed on this basis the procedures and instruments which measure the properties and predict the behaviour of materials. Quite important are also developments of technologies and equipment for control of thickness and adhesion of thin protective coatings on various bases, corrosion control of underground pipelines by indirect method, acoustic emission control of hydrogen and corrosion cracking in structural materials, etc. 

Nickel—Copper. In the soHd state, nickel and copper form a continuous soHd solution. The nickel-rich, nickel—copper alloys are characterized by a good compromise of strength and ductihty and are resistant to corrosion and stress corrosion ia many environments, ia particular water and seawater, nonoxidizing acids, neutral and alkaline salts, and alkaUes. These alloys are weldable and are characterized by elevated and high temperature mechanical properties for certain appHcations. The copper content ia these alloys also easure improved thermal coaductivity for heat exchange. MONEL alloy 400 is a typical nickel-rich, nickel—copper alloy ia which the nickel content is ca 66 wt %. MONEL alloy K-500 is essentially alloy 400 with small additions of aluminum and titanium. Aging of alloy K-500 results in very fine y -precipitates and increased strength (see also Copper alloys). 

In concrete, triethanolamine accelerates set time and increases early set strength (41—43). These ate often formulated as admixtures (44), for later addition to the concrete mixtures. Compared to calcium chloride, another common set accelerator, triethanolamine is less corrosive to steel-reinforcing materials, and gives a concrete that is more resistant to creep under stress (45). Triethanolamine can also neutralize any acid in the concrete and forms a salt with chlorides. Improvement of mechanical properties, whiteness, and more even distribution of iron impurities in the mixture of portland cements, can be effected by addition of 2% triethanolamine (46). Triethanolamine bottoms and alkanolamine soaps can also be used in these type appUcations. Waterproofing or sealing concrete can be accompUshed by using formulations containing triethanolamine (47,48). 

Film Adhesion. The adhesion of an inorganic thin film to a surface depends on the deformation and fracture modes associated with the failure (4). The strength of the adhesion depends on the mechanical properties of the substrate surface, fracture toughness of the interfacial material, and the appHed stress. Adhesion failure can occur owiag to mechanical stressing, corrosion, or diffusion of interfacial species away from the interface. The failure can be exacerbated by residual stresses in the film, a low fracture toughness of the interfacial material, or the chemical and thermal environment or species in the substrate, such as gases, that can diffuse to the interface. 

Bronzes are somewhat similar to brasses in mechanical properties and to high-zinc brasses in corrosion resistance (except that bronzes are not affected by stress cracking). Aluminum and silicon bronzes are very popiilar in the process industries because they combine good strength with corrosion resistance. 

Alloy 400 has good mechanical properties and is easy to fabricate in all wrought forms and castings. K-500 is a modified version of this alloy and can be thermally treated and is suitable for items requiring strength, as well as corrosion resistance. Alloy 400 has immunity to stress corrosion cracking and pitting in chlorides and caustic alkali solutions. 

It is notable that while it is possible to produce maraging steels with consistently uniform mechanical properties, the stress corrosion properties are subject to scatter, as indicated in Fig. 3.34. To a large extent this scatter is an indication of the greater sensitivity of s.c.c. resistance to metallurgical variables. Although the variation in cracking resistance is not well understood, and the reaction to certain treatments not always consistent, certain observations may be used to indicate guidelines for improved properties. 

Monel, the classic nickel-copper alloy with the metals in the ratio 2 1, is probably, after the stainless steels, the most commonly used alloy for chemical plant. It is easily worked and has good mechanical properties up to 500°C. It is more expensive than stainless steel but is not susceptible to stress-corrosion cracking in chloride solutions. Monel has good resistance to dilute mineral acids and can be used in reducing conditions, where the stainless steels would be unsuitable. It may be used for equipment handling, alkalies, organic acids and salts, and sea water. 

There are several incidents in the text where glass has been involved as a direct cause, either because of its chemical properties (alkalinity, corrosive attack), or its physical properties (actinic transparency, or mechanical limitations under stress). Some of these incidents may be found under the entries ... 

---