Reducing conditions

Depending on catalysts and conditions, products of hydrogenation can include furfuryl alcohol [98-00-0] tetrahdrofurfuryl alcohol [97-99-4] 2-meth5ifuran [534-22-5] and even 2-methyltetrahydrofuran [96-47-9]. Under strongly reducing conditions, the ring is opened. 

Activated carbons contain chemisorbed oxygen in varying amounts unless special cate is taken to eliminate it. Desired adsorption properties often depend upon the amount and type of chemisorbed oxygen species on the surface. Therefore, the adsorption properties of an activated carbon adsorbent depend on its prior temperature and oxygen-exposure history. In contrast, molecular sieve 2eohtes and other oxide adsorbents are not affected by oxidi2ing or reducing conditions. 

Heat treatment of related glasses melted under reducing conditions can yield a unique microfoamed material, or "gas-ceramic" (29). These materials consist of a matrix of BPO glass-ceramic filled with uniformly dispersed 1—10 p.m hydrogen-filled bubbles. The hydrogen evolves on ceranarning, most likely due to a redox reaction involving phosphite and hydroxyl ions. These materials can have densities as low as 0.5 g/cm and dielectric constants as low as 2. 

Unha.iring, Unhairing can be done either by a hair save or a hair pulp system. The hair pulp system is preferred by most tanners for its speed and labor efficiency. In the hair pulp system the hides are treated with sodium sulfide (sulfhydrate) and lime (calcium hydroxide). The hair is quickly destroyed by the strong alkaline reducing conditions. 

Cathode and insulator walls are less subject to severe electrochemical attack. In the case of the cathode wall, this is because of the reducing conditions which prevail, and in the case of the insulator wall, because the wall nominally carries no current. However, certain surfaces of cathode and insulator walls are anodic with respect to other surfaces, because of the axial electric field present in the generator, and these surfaces do require protection against electrochemical attack. 

Manganese Hydroxide. Manganese hydroxide [18933-05-6] is a weaMy amphoteric base having low solubihty in water. Mn(OH)2 crystals are reported to be almost pure white and darken on exposure to air. Manganese dihydroxide occurs in nature as the mineral pyrochroite and can also be prepared synthetically by reaction of manganese chloride and potassium hydroxide that is scmpulously free of oxygen. The entire reaction is conducted under reducing conditions (36). 

Another set of nickel aHoys, which have a high chromium content, a moderate molybdenum content, and some copper, are the ILLIUM aHoys. These cast aHoys are wear and erosion resistant and highly resistant to corrosion by acids and alkaHes under both oxidizing and reducing conditions. 

Method 2. Alcohol amination—metal cataly2ed amination of an alcohol over a metal catalyst under reducing conditions. 

Carbon, Carbides, and Nitrides. Carbon (graphite) is a good thermal and electrical conductor. It is not easily wetted by chemical action, which is an important consideration for corrosion resistance. As an important stmctural material at high temperature, pyrolytic graphite has shown a strength of 280 MPa (40,600 psi). It tends to oxidize at high temperatures, but can be used up to 2760°C for short periods in neutral or reducing conditions. The use of new composite materials made of carbon fibers is expected, especially in the field of aerospace stmcture. When heated under... 

Silicon carbide has very high thermal conductivity and can withstand thermal shock cycling without damage. It also is an electrical conductor and is used for electrical heating elements. Other carbides have relatively poor oxidation resistance. Under neutral or reducing conditions, several carbides have potential usehilness as technical ceramics in aerospace appHcation, eg, the carbides (qv) of B, Nb, Hf, Ta, Zr, Ti, V, Mo, and Cr. Ba, Be, Ca, and Sr carbides are hydrolyzed by water vapor. 

The loss of material at elevated temperatures is accelerated in vacuum and under reducing conditions. In the presence of carbon, for example, the following reaction may occur ... 

The ultraviolet cutoff or the absorption edge for pure vitreous siUca is 8.1 eV or 153 nm (171). This uv cutoff is influenced by the impurity level and stoichiometry of the material. Several impurities, such as the transition metals (Fe, Cu, Ti, etc) and alkaU metal ions (Na, Li, K), degrade the ultraviolet performance, shifting the uv cutoff to longer wavelengths. Ferric ions (Fe " ) cause absorption or result in network defects under reducing conditions. This contaminant at only a few ppm can be detected as an absorption at 230 nm and below (176). 

As the temperature rises, siUca (which is present in nearly all concentrates) also reacts with cassiterite under reducing conditions to give staimous siUcate ... 

Dyes in general and triaryknethane dyes in particular are rarely subjected to chemical processing once they have been formed. The introduction of substituents is usually carried out during the manufacture of the intermediates where the position and number of the groups introduced may be more precisely controlled. Dyes are sometimes exposed to oxidising and reducing conditions during appHcation and afterward. 

Hydroxides. The hydrolysis of uranium has been recendy reviewed (154,165,166), yet as noted in these compilations, studies are ongoing to continue identifying all of the numerous solution species and soHd phases. The very hard uranium(IV) ion hydrolyzes even in fairly strong acid (- 0.1 Af) and the hydrolysis is compHcated by the precipitation of insoluble hydroxides or oxides. There is reasonably good experimental evidence for the formation of the initial hydrolysis product, U(OH) " however, there is no direct evidence for other hydrolysis products such as U(OH) " 2> U(OH)" 2> U(OH)4 (or UO2 2H20). There are substantial amounts of data, particulady from solubiUty experiments, which are consistent with the neutral species U(OH)4 (154,167). It is unknown whether this species is monomeric or polymeric. A new study under reducing conditions in NaCl solution confirms its importance and reports that it is monomeric (168). 8olubihty studies indicate that the anionic species U(OH) , if it exists, is only of minor importance (169). There is limited evidence for polymeric species such as Ug(OH) " 25 (1 4). 

Coupling of butadiene with CO2 under electrochemically reducing conditions produces decadienedioic acid, and pentenoic acid, as weU as hexenedioic acid (192). A review article on diene telomerization reactions catalyzed by transition metal catalysts has been pubUshed (193). 

Because of the high temperatures and strong reducing conditions in the furnace a number of energy-consuming reactions take place. SiHca, the main impurity in the raw materials, may be partly volatilized as siHcon and later reoxidized in the cooler parts of the furnace. Some is reduced and combines with... 

Trace elements such as sulfur and nitrogen are also involved in the gasification reactions. Sulfur in coal is converted primarily to H2S under the reducing conditions of gasification. Approximately 5 to 15% of the sulfur is converted to COS, whereas the coal nitrogen is converted primarily to N, trace amounts of NH and HCN ate also formed. 

Cobalt(Il) dicobalt(Ill) tetroxide [1308-06-17, Co O, is a black cubic crystalline material containing about 72% cobalt. It is prepared by oxidation of cobalt metal at temperatures below 900°C or by pyrolysis in air of cobalt salts, usually the nitrate or chloride. The mixed valence oxide is insoluble in water and organic solvents and only partially soluble in mineral acids. Complete solubiUty can be effected by dissolution in acids under reducing conditions. It is used in enamels, semiconductors, and grinding wheels. Both oxides adsorb molecular oxygen at room temperatures. 

Most striking colors are obtained in glasses containing 10—20 wt % K2O, 10—22 wt % ZnO, and 50—60 wt % silica. CaO and 2 3 present (6). To this batch is added 1—3 wt % CdS, CdSe, and/or CdTe. Melting must be under neutral or mildly reducing conditions. Otherwise, S, Se, and Te will be oxidized to SO2, Se02, or Te02, which are colorless. 

Platinum and Platinum Alloys. Platinum has excellent resistance to strong acids and, at elevated temperatures, to oxidation. Under reducing conditions at high temperatures it must be protected from low-fusing elements or their oxides. Easily reduced metals at high temperatures may form low-fusing alloys with platinum. 

Reduced conditions are corrected, or normalised, conditions of temperature T, pressureand specific volume and are expressed mathematically as... 

Isoxazoles are readily cleaved under reducing conditions, and many examples have been reported (79AHC(25)147,63AHC(2)365). In the last three decades the potential of these reactions in synthesis has finally been realized, and the isoxazole ring has become a major tool as a masked enaminone (137) or 1,3-diketone, particularly for the synthesis of heterocycles. 

Halogen atoms in the 6-position of penicillanic acid are readily removed under reducing conditions (Scheme 33). Methyl 6,6-dibromopenicillanate is converted first to the 6a-bromo... 

---