Light stabilisation

Phosphites Tris-(p-nonylphenyl) phosphite (X) No Widely used in conjunction with conventional stabilisers (q.v.) in PVC. Some types appear to be useful heat and light stabilisers in polyolefins. Function primarily as peroxide decomposers rather than chain-breaking antioxidants. 

Fillers are often employed to reduce the surface tack of the final product. Examples are talc and china clay. If powdered materials are added directly to a latex they compete for the emulsion stabiliser present and tend to coagulate the latex. They are therefore added as an aqueous dispersion prepared by ball milling the filler with water and a dispersing agent, for example a naphthalene formaldehyde sulphonate at a concentration of about 1% of the water content. Heat and light stabilisers which are solids must be added in the same way. 

Amongst heat stabilisers are copper salts, phosphoric acid esters,phenyl-3-naphthylamine, mercaptobenzothiazole and mercaptobenzimidazole. Of these, copper salts in conjunction with halides have been found particularly effective, and some automotive specifications require the use of copper for heat stabilisation. Light stabilisers include carbon black and various phenolic materials. 

Hexa is used almost universally as the hardener. It is made by passing a slight excess of ammonia through a lightly stabilised aqueous solution of formaldehyde, concentrating the liquor formed and crystallising out the hexa (Figure 23.17). 

Heat stabilisers 12 release agents Light stabilisers 3... 

Obviously, use of such databases often fails in case of interaction between additives. As an example we mention additive/antistat interaction in PP, as observed by Dieckmann et al. [166], In this case analysis and performance data demonstrate chemical interaction between glycerol esters and acid neutralisers. This phenomenon is pronounced when the additive is a strong base, like synthetic hydrotalcite, or a metal carboxylate. Similar problems may arise after ageing of a polymer. A common request in a technical support analytical laboratory is to analyse the additives in a sample that has prematurely failed in an exposure test, when at best an unexposed control sample is available. Under some circumstances, heat or light exposure may have transformed the additive into other products. Reaction product identification then usually requires a general library of their spectroscopic or mass spectrometric profiles. For example, Bell et al. [167] have focused attention on the degradation of light stabilisers and antioxidants... 

Oligomeric hindered amine light stabilisers, such as Tinuvin 622 and Chimassorb 944, resist satisfactory analysis by conventional HPLC and have required direct UV spectroscopic analysis of a polyolefin extract [596], PyGC of an extract [618,648], or SEC of an extract [649]. Freitag et al. [616] determined Tinuvin 622 in LDPE, HDPE and PP by saponification of the polymer dissolution in hot toluene via addition of an... 

David et al. [184] have shown that cool on-column injection and the use of deactivated thermally stable columns in CGC-FID and CGC-F1D-MS for quantitative determination of additives (antistatics, antifogging agents, UV and light stabilisers, antioxidants, etc.) in mixtures prevents thermal degradation of high-MW compounds. Perkins et al. [101] have reported development of an analysis method for 100 ppm polymer additives in a 500 p,L SEC fraction in DCM by means of at-column GC (total elution time 27 min repeatability 3-7 %). Requirements for the method were (i) on-line (ii) use of whole fraction (LVI) and (iii) determination of high-MW compounds (1200 Da) at low concentrations. Difficult matrix introduction (DMI) and selective extraction can be used for GC analysis of silicone oil contamination in paints and other complex analytical problems. 

Oligomeric additives with broad MWD tend to be a problem in conventional HPLC conditions. In cases where no interest exists in the oligomer distribution it is common practice to solve the problem by creating a uniform structural unit useful for analysis. For example, isocratic (or gradient) LC-UV was used for the determination of the polymeric light stabiliser Tinuvin 622 in polyolefins using dissolution (toluene)/derivatisation (TBAH)-precipitation (alcohol) the diol formed was quantitatively determined by NPLC [653]. 

An excellent and comprehensive review has covered HPLC analysis of AOs and light stabilisers up to 1990 [576]. Normal vs. reversed-phase and isocratic vs. gradient-elution HPLC separation of synthetic mixtures of additives and of solvent extracts from polymers were discussed. 

---