Knife, knives

The surface layer on lumps of sodium is removed with a large knife, the clean sodium is rapidly weighed out on a few large Alter papers and immediately trans. ferred to a beaker containing sodium-dried ether. The sodium may then be removed at leisure, cut into small pieces and transferred to the flask. 

If it is desired to employ fluoboric acid HBF4, it can be prepared by adding 100 g. of A.R. boric acid in small proportions to 325 g. of A.R. hydrofluoric acid (40 p>er cent. HF) cooled in ice the hydrofluoric acid is contained in a Bakelite beaker, a beaker coated with wax or in a lead vessel. A simple container may also be prepared by cutting of the neck of the wax bottle (in which the hydrofluoric acid is supplied) with a large e.g., a butcher s ) knife which has been slightly warmed. One-third of the above solution should be employed in the preparation. Handle unth great care. 

It is one of the most reactive and electropositive of metals. Except for lithium, it is the lightest known metal. It is soft, easily cut with a knife, and is silvery in appearance immediately after a fresh surface is exposed. It rapidly oxidizes in air and must be preserved in a mineral oil such as kerosene. 

Lanthanum is silvery white, malleable, ductile, and soft enough to be cut with a knife. It is one of the most reactive of the rare-earth metals. It oxidizes rapidly when exposed to air. Cold water attacks lanthanum slowly, while hot water attacks it much more rapidly. 

When freshly exposed to air, thallium exhibits a metallic luster, but soon develops a bluish-gray tinge, resembling lead in appearance. A heavy oxide builds up on thallium if left in air, and in the presence of water the hydride is formed. The metal is very soft and malleable. It can be cut with a knife. Twenty five isotopic forms of thallium, with atomic masses ranging from 184 to 210 are recognized. Natural thallium is a mixture of two isotopes. A mercury-thallium alloy, which forms a eutectic at 8.5% thallium, is reported to freeze at -60C, some 20 degrees below the freezing point of mercury. 

Alkali solutions and dilute and concentrated acids attack the metal rapidly. The pure metal is likely to ignite if scratched with a knife. 

The element has a metallic, bright silver luster. It is relatively stable in air at room temperature, and is readily attacked and dissolved, with the evolution of hydrogen, but dilute and concentrated mineral acids. The metal is soft enough to be cut with a knife and can be machined without sparking if overheating is avoided. Small amounts of impurities can greatly affect its physical properties. 

This method is by far the easiest of the two methods I descnbe, but because it uses bromine liquid as a precursor to the dibromodioxane crystals a fume cupboard (or a fucking good method of fume extraction) is absolutely essential. Surgically removing ones gonads with a blunt knife would be a much less painful way of harming yourself than messing with this stuff in the kitchen. 

Kneaders Kneading Kneading mixers Knecht compound Knecht method Knife mills Knight and Allen Knives Knize Ten Knockdown Knockdown resistance... 

Other veneers for backs and cores, or in the case of the tropical luauns, are almost always peeled on a rotary lathe. In this process, the log is rotated against along, stationary knife and the log is essentially "unroUed" in along, thin sheet. These sheets are called rotary-cut veneers. 

After the block is chucked in the lathe, the lathe turns the block against the knife and peels the veneer in a continuous sheet as the knife moves toward the center of the block. When the knife cannot advance further without moving into the metal chucks, the lathe is stopped, the core of the block is dropped, the lathe is recharged, and the cycle repeated. 

The film is fibrillated mechanically by mbbing or bmshing. Immiscible polymers, such as polyethylene or polystyrene (PS), may be added to polypropylene to promote fibrillation. Many common fiber-texturing techniques such as stuffer-box, false-twist, or knife-edge treatments improve the textile characteristics of slit-film fibers. 

In the Philippines, the principal suppHer of abaca fiber, the fibrous layer ia the sheath is separated with a knife between the layers, and the strips of fiber-containing layers, called tuxies, are pulled off and cleaned by hand to remove the pulp. In Indonesia and Central America these operations are performed mechanically. Hand- and spiadle-stripped fiber is graded for braids, fine textiles, and cordage decorticated fiber is another class. A cross-sectional view is shown ia Figure 4a. The abaca fiber has a large lumen and the presence of siUcified plates is not unusual. 

In the precoat mode, filter aids allow filtration of very fine or compressible soHds from suspensions of 5% or lower soHds concentration on a rotary dmm precoat filter. This modification of the rotary dmm vacuum filter uses an advancing knife continuously to skim off the separated soHds and the... 

---