Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Ion selective electrodes, determination

T. P. Kinetic Studies with Ion-Selective Electrodes Determination of Greatinine in Urine with a Picrate Ion-Selective Electrode, /. Chem. Educ. 1983, 60, 74-76. [Pg.659]

J. F. Liebman, M. Ponikvar, Ion selective electrode determination of free versus total fluoride ion in simple and fluoroligand coordinated hexafluoropnictate (PnF6-, Pn = P, As, Sb, Bi) salts. Struct. Chem. 16 (2005) 521-528. [Pg.542]

Ion-selective electrode -determination of silver [SILVER COMPOUNDS] (Vol 22) -for fluoride analysis pLUORINE COMPOUNDS, INORGANIC - INTRODUCTION] (Vol 11) -for fluoroborates pLUORINE COMPOUNDS, INORGANIC - BORON - FLUQROBORIC ACID] (Vol 11) -for hydrogen ion activity [HYDROGEN-LON ACTIVITY] (Vol 13)... [Pg.521]

Livanos, G., Milbam, P.J. (1984). Fluoride ion-selective electrode determination of sodium monofluoroacetate in meat baits and formulations. J. Assoc. Anal. Chem. 67 10-12. [Pg.195]

A measurement method based on an ion-selective electrode determination of chloride is suggested. This method is reasonably simple, rugged, and can be run for long times without attention. Several variations of this technique are considered. One variation is a conventional electrode measurement except that the flowing-junction reference electrode can be replaced by a fluoride ion selective electrode as a nonflowing reference. Another method was developed and evaluated for the measurement of very small aerosol samples the measurement of chloride ion concentration is made on 50-/>tL samples. When the major-constituent composition of sea salt is known, the total aerosol weight can be calculated. The small volume allows measurable concentrations to be attained with short sample collection times. This technique is described in detail later. [Pg.63]

Lewis, S.C. and Miller, K.W. (1981). Performance evaluation of the Kodak Ektachem 400 analyzer Potentiometric (ion selective electrode) determinations. Clin. Chem. 27, III, Abstr. 448. [Pg.274]

E643 Kubasik, N.P., Cordy, P.A., Mayer, T.K. and D Souza, J.P. (1990). Potassium by ion selective electrode determined with Abbott s Vision System . Clin. Chem. 36, 1071, Abstr. 556. [Pg.307]

Convention Reporting Results of Ion-Selective Electrode Determinations of Sodium and Potassium... [Pg.312]

Results of ion-selective electrode determinations of sodium and potassium in whole blood and undiluted plasma should be reported in terms of concentration (mmol/1). [Pg.312]

When first developed, potentiometry was restricted to redox equilibria at metallic electrodes, limiting its application to a few ions. In 1906, Cremer discovered that a potential difference exists between the two sides of a thin glass membrane when opposite sides of the membrane are in contact with solutions containing different concentrations of H3O+. This discovery led to the development of the glass pH electrode in 1909. Other types of membranes also yield useful potentials. Kolthoff and Sanders, for example, showed in 1937 that pellets made from AgCl could be used to determine the concentration of Ag+. Electrodes based on membrane potentials are called ion-selective electrodes, and their continued development has extended potentiometry to a diverse array of analytes. [Pg.465]

The concentration of Ca + in a sample of sea water is determined using a Ca ion-selective electrode and a one-point standard addition. A 10.00-mL sample is transferred to a 100-mL volumetric flask and diluted to volume. A 50.00-mL aliquot of sample is placed in a beaker with the Ca ion-selective electrode and a reference electrode, and the potential is measured as -0.05290 V. A 1.00-mL aliquot of a 5.00 X 10 M standard solution of Ca + is added, and a potential of -0.04417 V is measured. What is the concentration of Ca + in the sample of sea water ... [Pg.488]

Potcntiomctric Titrations In Chapter 9 we noted that one method for determining the equivalence point of an acid-base titration is to follow the change in pH with a pH electrode. The potentiometric determination of equivalence points is feasible for acid-base, complexation, redox, and precipitation titrations, as well as for titrations in aqueous and nonaqueous solvents. Acid-base, complexation, and precipitation potentiometric titrations are usually monitored with an ion-selective electrode that is selective for the analyte, although an electrode that is selective for the titrant or a reaction product also can be used. A redox electrode, such as a Pt wire, and a reference electrode are used for potentiometric redox titrations. More details about potentiometric titrations are found in Chapter 9. [Pg.494]

Selectivity As described earlier, most ion-selective electrodes respond to more than one analyte. For many ion-selective electrodes, however, the selectivity for the analyte is significantly greater than for most interfering ions. Published selectivity coefficients for ion-selective electrodes (representative values are found in Tables 11.1 through 11.3) provide a useful guide in helping the analyst determine whether a potentiometric analysis is feasible for a given sample. [Pg.496]

Potentiometric electrodes also can be designed to respond to molecules by incorporating a reaction producing an ion whose concentration can be determined using a traditional ion-selective electrode. Gas-sensing electrodes, for example, include a gas-permeable membrane that isolates the ion-selective electrode from the solution containing the analyte. Diffusion of a dissolved gas across the membrane alters the composition of the inner solution in a manner that can be followed with an ion-selective electrode. Enzyme electrodes operate in the same way. [Pg.532]

The preparation of an ion-selective electrode for salicylate is described. The electrode incorporates an ion-pair of crystal violet and salicylate in a PVC matrix as the ion-selective membrane. Its use for the determination of acetylsalicylic acid in aspirin tablets is described. A similar experiment is described by Creager, S. E. Lawrence, K. D. Tibbets, C. R. in An Easily Constructed Salicylate-Ion-Selective Electrode for Use in the Instructional Laboratory, /. Chem. Educ. 1995, 72, 274-276. [Pg.533]

Directions are provided for constructing and characterizing an ammonium ion-selective electrode. The electrode is then modified to respond to urea by adding a few milligrams of urease and covering with a section of dialysis membrane. Directions for determining urea in serum also are provided. [Pg.533]

The titration of AF+ with E in a water-acetonitrile mixture is followed potentiometrically using a fluoride ion-selective electrode. The cumulative formation constant for AlEs is determined from the titration curve. [Pg.534]

Creager and colleagues designed a salicylate ion-selective electrode using a PVC membrane impregnated with tetraalkylammonium salicylate. To determine the ion-selective electrode s selectivity coefficient for benzoate,... [Pg.535]

Ion-selective electrodes can be incorporated in flow cells to monitor the concentration of an analyte in standards and samples that are pumped through the flow cell. As the analyte passes through the cell, a potential spike is recorded instead of a steady-state potential. The concentration of K+ in serum has been determined in this fashion, using standards prepared in a matrix of 0.014 M NaCl. ... [Pg.536]

The concentration of NO3 in a water sample is determined by a one-point standard addition using an N03 ion-selective electrode. A 25.00-mL sample is placed in a beaker, and a potential of -t0.102 V is measured. A 1.00-mL aliquot of a 200.0 ppm standard solution of N03 is added, after which the potential is found to be -t0.089 V. Report the concentration of N03 in parts per million. [Pg.537]

Determine the parts per million of F in the tap water, (b) For the analysis of toothpaste a 0.3619-g sample was transferred to a 100-mL volumetric flask along with 50.0 mL of TISAB and diluted to volume with distilled water. Three 20.0-mL aliquots were removed, and the potential was measured with an L ion-selective electrode using a saturated calomel electrode as a reference. Live separate 1.00-mL additions of a 100.0-ppm solution of L were added to each, measuring the potential following each addition. [Pg.537]

You are responsible for determining the amount of KI in iodized salt and decide to use an D ion-selective electrode. Describe how you would perform this analysis using... [Pg.537]

This experiment includes instructions for preparing a picrate ion-selective electrode. The application of the electrode in determining the concentration of creatinine in urine (which is further described in Method 13.1) also is outlined. [Pg.659]

National Institute of Standards and Technology (NIST). The NIST is the source of many of the standards used in chemical and physical analyses in the United States and throughout the world. The standards prepared and distributed by the NIST are used to caUbrate measurement systems and to provide a central basis for uniformity and accuracy of measurement. At present, over 1200 Standard Reference Materials (SRMs) are available and are described by the NIST (15). Included are many steels, nonferrous alloys, high purity metals, primary standards for use in volumetric analysis, microchemical standards, clinical laboratory standards, biological material certified for trace elements, environmental standards, trace element standards, ion-activity standards (for pH and ion-selective electrodes), freezing and melting point standards, colorimetry standards, optical standards, radioactivity standards, particle-size standards, and density standards. Certificates are issued with the standard reference materials showing values for the parameters that have been determined. [Pg.447]

Eluorspar assay may be completed by fluoride determination alone, because the mineralogical grouping rarely iacludes fluorine minerals other than fluorite. Calcium can be determined as oxalate or by ion-selective electrodes (67). SiUca can be determined ia the residue from solution ia perchloric acid—boric acid mixture by measuriag the loss ia weight on Aiming off with hydrofluoric acid. Another method for determining siUca ia fluorspar is the ASTM Standard Test Method E463-72. [Pg.175]

Methods for iodine deterrnination in foods using colorimetry (95,96), ion-selective electrodes (94,97), micro acid digestion methods (98), and gas chromatography (99) suffer some limitations such as potential interferences, possibHity of contamination, and loss during analysis. More recendy neutron activation analysis, which is probably the most sensitive analytical technique for determining iodine, has also been used (100—102). [Pg.364]

The sodium hydroxide is titrated with HCl. In a thermometric titration (92), the sibcate solution is treated first with hydrochloric acid to measure Na20 and then with hydrofluoric acid to determine precipitated Si02. Lower sibca concentrations are measured with the sibcomolybdate colorimetric method or instmmental techniques. X-ray fluorescence, atomic absorption and plasma emission spectroscopies, ion-selective electrodes, and ion chromatography are utilized to detect principal components as weU as trace cationic and anionic impurities. Eourier transform infrared, ft-nmr, laser Raman, and x-ray... [Pg.11]

Instmmental methods are useful for the determination of the total silver ia a sample, but such methods do not differentiate the various species of silver that may be present. A silver ion-selective electrode measures the activity of the silver ions present ia a solution. These activity values can be related to the concentration of the free silver ion ia the solution. Commercially available silver ion-selective electrodes measure Ag+ down to 10 flg/L, and special silver ion electrodes can measure free silver ion at 1 ng/L (27) (see Electro analytical techniques). [Pg.91]

Nitrate can also be measured potentiometrically with an ion-selective electrode at 10 10 M (24,25). This method is suggested as a screening method for determining the approximate nitrate concentration (20). Ion chromatography can be used for nitrate concentrations of 2 to 10 ppb (23). [Pg.231]

Cyanide compounds are classified as either simple or complex. It is usually necessary to decompose complex cyanides by an acid reflux. The cyanide is then distilled into sodium hydroxide to remove compounds that would interfere in analysis. Extreme care should be taken during the distillation as toxic hydrogen cyanide is generated. The cyanide in the alkaline distillate can then be measured potentiometricaHy with an ion-selective electrode. Alternatively, the cyanide can be determined colorimetricaHy. It is converted to cyanogen chloride by reaction with chloramine-T at pH <8. The CNCl then reacts with a pyridine barbituric acid reagent to form a red-blue dye. [Pg.232]

Both of these haUdes can also be determined potentiometricaHy with an appropriate ion-selective electrode. Sulfide and cyanide both interfere with the electrode response. [Pg.232]

Ammonia.. The most rehable results for ammonia are obtained from fresh samples. Storage of acidified samples at 4°C is the best way to minimi2e losses if prompt analysis is impossible. The sample acidity is neutrali2ed prior to analysis. Ammonia concentrations of 10 -0.5 M can be determined potentiometricaHy with the gas-sensing, ion-selective electrode. Volatile amines are the only known interferents. [Pg.232]

Chlorine and fluorine in beryUium metal are isolated by pyrohydrolysis or by distUlation (21). Fluoride and chloride in the condensate are determined by ion-selective electrode or colorimetricaUy. [Pg.69]

The potentiometry sensor (ion-selective electrode) controls application for determination of polymeric surface-active substances now gets the increasing value. Potentiometry sensor controls are actively used due to simple instmment registration, a wide range of determined concentrations, and opportunity of continuous substances contents definition. That less, the ionometry application for the cation polymeric SAS analysis in a solution is limited by complexity of polycation charge determination and ion-exchanger synthesis. [Pg.108]

USING OF ION SELECTIVE ELECTRODES FOR THE DETERMINATION OF THE IONIC LIQUIDS SOLUBILITY... [Pg.153]

Many double-charged anions, such as sulfate, hydrophosphate, oxalate etc., are highly widespread in natural sources and at the same time lack any convenient technique for their determination. Therefore, development of ion-selective electrodes (ISEs), responsive to these anions, is of great practical importance. However, for a long time all attempts directed toward creation of such electrodes were unsuccessful (except for carbonate ISEs based on trifluoroacetylbenzene derivatives), and only in recent years this field has shown significant progress. [Pg.302]

The sufficient selectivity to a principal component is the most important condition determining the possibility of ion-selective electrodes (ISEs) practical appliances. In this work, the relationship between the potentiometric selectivity of alkylammonium-selective electrodes and factors such as the nature of plasticizer, ion-exchanger and substitution degree of cationic nitrogen atoms of the principal and foreign ions, is discussed. [Pg.314]


See other pages where Ion selective electrodes, determination is mentioned: [Pg.190]    [Pg.36]    [Pg.477]    [Pg.480]    [Pg.489]    [Pg.652]    [Pg.103]    [Pg.141]    [Pg.421]    [Pg.55]    [Pg.153]   


SEARCH



Ion determinations

Ion electrodes

Ion-selective electrode selectivity

Ion-selective electrodes

The Selectivity of Ion-selective Electrodes and Its Determination

© 2024 chempedia.info